Regin Technology SkyBox S1 Instruction manual

1
SkyBox S1 Quick User Guide
Package Contents
SkyBox S1 Skype phone saving box
Type B (A male to B male) USB cable
Telephone cable
SkyBox S1 Setup CD: SkyBox S1 Setup program, EN, TC and SC user
manual & quick user guide
User can download latest SkyBox S1 related document from Regin Tech
web site: http://www.regintech.com.tw/download.htm
Quick Installation Procedure
1. Make sure your PC with internet access and download latest Skype
version or Skype version 6.14 or later from http://www.skype.com
2. Remove SkyBox S1, USB cable, telephone cable and SkyBox S1 setup
CD from SkyBox S1 package
3. Connect SkyBox S1 USB port with your computer USB port
4. Connect SkyBox S1 Phone port to one PBX trunk line or a regular analog
phone RJ-11 port through telephone cable and make sure phone is
on-hook properly
5. Connect SkyBox S1 Line port to your landline(or via RJ11 jack on the wall)
through the existing telephone cable

2
6. Put SkyBox S1 setup wizard CD into your computer CD disk and
double-click setup.exe.
7. In Windows 2000, user might get below “Digital Signature Not Found”
window. Click Yes to continue installation.

3
8. The “Select Setup Language”window pops up. Choose a preferred
language by scrolling down the selection bar. After choosing the language,
click OK.
9. The “Welcome to the SkyBox S1 Setup Wizard” appears. Read the
on-screen instructions and click Next.
10. Following the on screen instructions step by step to complete SkyBox S1
installation. After launching SkyBox S1, Skype will pop out one warning
window as below figure. SkyBox S1 software usually will automatically
click “Allow access”option, but user can manually click “Allow access”in
case SkyBox S1 doesn’t make it. User can refer SkyBox S1 user manual
chapter 5 FAQ Q6 for more information.
11. Set up one to five digits Skype speed dial numbers for your Skype contact
list from SkyBox S1 system tray icon as below figure after SkyBox S1
software is running. The speed dial contact list can be exported for back
up and imported for use in the future. Whenever there is the problem to
import speed dial list or speed dial list is missing, please try “Restore the
latest setting” button to restore the last speed dial setting saved on the

4
GUI.
12. If the Default operation mode in General tab is VoIP( check from Option
dialogue of SkyBox S1 system tray icon in the right-bottom corner of
Windows), user will hear a different Skype dial tone and notice blue LED is
solid-on when the phone receiver is picked up. User can follow below
steps 13~15 to make Skype/SkypeOut calls. Or user can press “# “key to
switch to the Landline mode( Green LED is solid on when the phone is
hook off) and hear a familiar landline dial tone, then make a landline call
as you did in the past. If user changes default operation mode as Landline
mode, user will hear a familiar landline dial tone and notice green LED is
solid-on when the phone receiver is picked up. Then make a landline call
as you did in the past. User can press “# “key to switch to the VoIP mode
and hear a different Skype dial tone and notice blue LED is solid-on when
the phone receiver is picked up. User can follow below steps 13~15 to
make Skype/SkypeOut calls.
13. When SkyBox S1 is in the VoIP mode, pick up your phone receiver or

5
handset( blue LED is solid-on) and dial Skype contact’s speed dial
number + “#” key through the phone keypad after hearing a Skype dial
tone and then enjoy a Skype call. Add “# “key will accelerate the Skype
call to be calling out, but it is not necessary.
14. For a SkypeOut™call, dial “00” (or “+” key) + country code +
phone number + “#”key through the phone keypad or setup a
SkypeOut contact list and call out by Skype speed dial number.
Add “# “key will accelerate the SkypeOut call to be calling out, but
it is not necessary. For example, user can make a call to one U.S.A.
number by pressing 00-1-408-888-8888. If SkypeOut country code
and area code are set as below figure, user can omit 00 + country
code or even area code when making a SkypeOut call.
15. When there is a phone ring for an incoming call, pick up your phone
receiver or handset to answer the call and hang up phone or click End call
from Skype GUI to finish the call.
Note:

6
1. SkyBox S1 setup installation needs to be under user with administrator
privilege.
2. SkyBox S1 is quite different with general USB devices like USB
keyboard or USB mouse. It needs 5V, 500mA power from the USB port.
If SkyBox S1 can't work properly after this device is successfully installed,
please unplug this device and plug into another PC USB port, or replace
the USB cable with a new good quality one between this device and PC
USB port or use USB hub with power adapter to connect this device and
PC USB port.
We found some PC USB port at the front panel is extended from
motherboard through extension connector/cable and sometimes the
connector/cable is at bad quality. It might cause SkyBox S1 malfunction.
For this case, we recommend you to plug SkyBox S1 into USB ports at PC
rear panel or use one USB hub with power adapter to connect PC USB port
and SkyBox S1.
3. After SkyBox S1 software is running, user can click SkyBox S1 tray icon
with right mouse from right-bottom of PC desktop for “check for latest
update” and “about”. About will tell you what’s the SkyBox S1 software
version you installed. If the result for check latest update has newer version
than your current installation, you can download for use.
Customer support service
Regin Technology Corp. LTD.
TEL: [phone]
FAX: [phone]
Mobile: [phone]
E-mail: henr[email protected].tw
Skype: regin.skype
http://www.regintech.com.tw
Service hours: 0900~1800 (GMT+08:00 Taipei) office hour