Reina ARNAGE DE-ARG0805 User manual

ARNAGE TOWEL RAIL
INSTALLATION GUIDE
Please read these instructions carefully before instalation and operation
1.This Towel Rail is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning
use of the Towel Rail by a person responsible for their safety.
2.In order to avoid a hazard, this Towel Rail must be installed so that the bottom
rail is at least 600mm above the floor.
3.This Towel Rail is intended to warm and dry towels and therefore is hot to the
touch.
4.The towel rail is to be installed so that switches and other controls cannot be
touched by a person in the bath or shower.
5.To avoid a hazard this towel rail must not be used to hold towels or any other
articles that have been in contact with oil, petroleum based products or dry
cleaning fluids.
6.Use this Towel Rail only with the voltage specified on the rating label.
7.Do not immerse in liquid or allow liquid to run into the interior of the Towel
Rail. Indoor use only.
8.Do not operate this towel rail if damaged or after the Towel Rail malfunctions
or has been dropped or damaged in any manner. Return to a qualified electrical
person for examination, electrical service or repair.
9.Use this Towel Rail only as described in this manual. Any other use is not
recommended by the manufacturer and may cause fire, electrical shock or
injury.
10. Do not use this Towel Rail in a window as rain may cause electric shock.

TOOLS REQUIED Step 1
Step 2
Step 3
Pencil
Hammer
Measuring Tape
Spirit level
Electric drill
Screw driver
Hex key
Wall anchors x8 Applided models
Screws M6*45
x8
DE-ARG0805 DE-ARG1205
Screw M6*18 x1
Screw M6*20 x4
Decorative cap x4
Mounting seat x4
Mounting leg single
hole x3
Mounting leg two holes
x1
Code Size Power Voltage
DE-ARG0805 800*500MM 90W 220-240VAC,50HZ
DE-ARG1205 1200*500CM 130W 220-240VAC,50HZ
ACCESSORIES
Please follow the below installation steps to complete the towel rail installation
Step 4
Fix 3 mounting single hole tubes to the
threaded holes on the vertical bar,
Screw down the mounting screw with a
screwdriver.
Guide the electrical cord through the
electrical connection two holes mount-
ing tube and use the short mounting
screw to tighten theelectrical connec-
tion mounting tube to the vertical bar.
Use a measuring tape to measure the
distance between the center points of
each wall bracket tube,and mark the
installation holes by pencil.
Make the holes with an electric driller

Step 7
Step 8
Step 9
Step 5
Step 6
Be sure to drill a hole for the core cable
going from the leg to the wall on the
right lower mounting leg.
Use a hammer to knock plastic wall
anchor into wall completely
Insert long screw through mounting
seat , then screw into the plastic wall
anthor with a screw driver. And put the
decorative cap against the mounting
seat
Connect the core wire from the leg to the
power wire inside the wall
Lie the towel warmer against the mounting
seat fixed on the wall.
Install the hex screws into the hole of all
the tubes using the allen wrench and fix
the towel warmer tube onto the mounting
bracket.

How to use the TIMER on the towel rail?
1)Consistant 24 hours ON
2)2H: 2 hours ON,stop working automatically after 2 hours
3)4H: 4 hours ON,stop working automatically after 2 hours
4)A2( Automatic working mode),2 hours ON,2 hours OFF,then 2 hours ON and
2 hours OFF automatically working as circulation way.
5)A4( Automatic working mode),4 hours ON,4 hours OFF,then 4 hours ON and
4 hours OFF automatically working as circulation way.
Only Pressing the right button on the display,now it is power on and simul-
taneously it will be working for consistant 24 hours ,no matter what number
showing on the ditigal screen.
If you want to use the boost TIMER working by hours,then press the left
button ,you can select 2H- 4H- A2- A4 (as above description), a blue
cursor between two words on the display will flash to indicate the rail is
beginning to work under current selected TIMING mode.
TIMER working mode :