Remington F3700AU User manual
3. Gently tap the shaver head on a flat surface to remove any
loose hair particles, and rinse the shaver head under warm
water (Diagram J). Never submerge your
shaver under water.
4. Thoroughly clean the cutter and trimmer
with a brush (Diagram J).
5. Never use the cleaning brush on the foils,
as damage may occur.
6. Shake off any excess water.
7. Leave the shave unit open to allow the
shaver to
dry completely.
8. Lubricate the shaver with a spray of
Remington® Shaver Saver (SP4) on the
foil and cutters.
9. Replace the head assembly, simply by
pushing it on the shaver.
Cover shaver head with the protective head guard between
uses. When removing the head guard or placing it back onto
the shaver, do not apply pressure to the floating cutter
surfaces, as you may damage them.
Lubricate
Remington® Shaver Saver (SP-4) lubricates, cleans and
protects your shaver’s foil and cutter assembly. The lubricant
helps remove hair clippings while reducing wear. Spray on the
foil and cutters after each shave to keep your shaver operating
at peak performance.
Cleaning Cautions
•Never submerge the shaver completely into water.
•Never clean the shaver or replace the cutters while it is
plugged into an electrical outlet.
•Do not use any aggressive cleaning agents, as this may
damage the shaver.
Replacing Your Heads & Cutters
It is very important to replace your foils and cutters when
necessary to ensure a close, comfortable shave without
I
J
irritation. We recommend they be replaced every 6 months for
optimal performance. Here are some signs of head and cutter
wear, indicating that replacement is needed.
Signs that your foils and cutters need replacing:
• Irritation:Asfoilsgetworn,youmayexperienceskinirritation.
Asthefoilsbecomeexcessivelywornyoumayexperience
some skin irritation or redness.
• Pulling:Asthecutterswear,yourshavemaynotfeelasclose
and you may feel your cutter pulling your hair.
• Wearthrough:Youmaynoticethatthecuttershaveworn
through the foils.
TO REPLACE THE FOIL
• Pullthefoilassemblyuptoremovefromthehairpocket.
• Insertnewfoilassemblyinhairpocketuntilitsnapsinplace.
TO REPLACE THE CUTTERS
• Graspcutterbetweenthumbandforefingerandpullupward.
• Snapbothnewcutterassembliesintotopofoscillatortips.
STORAGE
When not in use, always unplug the power adaptor from the
power outlet. Never wrap the cord of the power adaptor
around the unit as this will cause the cord to wear prematurely
and break. Handle the cord carefully for long life and avoid
jerking, twisting or straining especially at the power plug. If the
cord becomes twisted in use, periodically straighten it.
2 YEAR WARRANTY F3700AU
MONEY BACK OFFER - Australia/New Zealand Only
If within 30 days you are not fully satisfied with your
Remington® shaver, just return the shaver with this completed
couponandacopyofyourAustralian/NewZealandpurchase
receipt to Remington®. In return, we will send you a cheque for
the full purchase price of the shaver. Please allow 6-8 weeks
for your cheque to arrive.
Name:
Address:
City:
State: Postcode:
1211 13 14
Spectrum Brands Australia Pty Ltd and Spectrum Brands New Zealand Limited
WARRANTY AGAINST DEFECTS
In this warranty:
Australian Consumer Law means the Australian consumer law set out in Schedule 2
to the Competition and Consumer Act 2010;
CGA means the New Zealand Consumer Guarantees Act 1993;
Goods means the product or equipment which was accompanied by this warranty and
purchased in Australia or New Zealand, as the case may be;
Manufacturer, We or us means:
1. for Goods purchased in Australia, Spectrum Brands Australia Pty Ltd
ACN, 007 070 573; or
2. for Goods purchased in New Zealand, Spectrum Brands New Zealand Limited,
as the case may be, contact details as set out at the end of this warranty;
Supplier means the authorised distributor or retailer of the Goods that sold you the Goods
in Australia or in New Zealand; and
You means you, the original end-user purchaser of the Goods.
1. Our goods come with guarantees that cannot be excluded under the Australian
Consumer Law, or the CGA. You are entitled to a replacement or refund for a major failure
and compensation for any other reasonably foreseeable loss or damage. You are also
entitled to have the goods repaired or replaced if the goods fail to be of acceptable
quality and the failure does not amount to a major failure.
2. The benefits provided by this Warranty are in addition to all other rights and remedies in
respect of the Goods which the consumer has under either the Australian Consumer Law
or the CGA. The original purchaser of the Goods is provided with the following Warranty
subject to the Warranty Conditions:
3. We warrant the Goods for all parts defective in workmanship or materials for the period
of two (2) years from the date of purchase (Warranty Period). If the Goods prove
defective within the Warranty Period by reason of improper workmanship or material,
we may, at our own discretion, repair or replace the Goods without charge.
Warranty Conditions
4. The Goods must be used in accordance with the manufacturer’s instructions. This
Warranty does not apply should the defect in or failure of the Goods be attributable to
misuse, abuse, accident or non-observance of manufacturer’s instructions on the part of
the user. As far as the law permits, the manufacturer does not accept liability for any
direct or consequential loss, damage or other expense caused by or arising out of any
failure to use the Goods in accordance with the manufacturer’s instructions.
5. Exhaustible components (such as shaver heads, cutters and foils) of the Goods
are included under this Warranty only where there is a defect in workmanship or
materials used.
6. The warranty granted under clause 3 is limited to repair or replacement only.
7. Any parts of the Goods replaced during repairs or any product replaced remain the
property of the manufacturer. In the event of the Goods being replaced during the
Warranty Period, the warranty on the replacement Goods will expire on the same date
as for the Warranty Period on the original Goods which are replaced.
8. In order to claim under the warranty granted under clause 3 you must:
(a) Retain this warranty with your receipt/proof of purchase; and
(b) Return the Goods to us at the relevant address below or to the Supplier by prepaid
freight within the Warranty Period accompanied with (i) the legible and unmodified
original proof of purchase, which clearly indicates the name and address of the
Supplier, the date and place of purchase, the product name or other product serial
number and (ii) this warranty.
9. This warranty is immediately void if:
(a) Any serial number or appliance plate is removed or defaced;
(b) The Goods have been serviced or otherwise repaired by a person not authorised to
do so by us or where non approved replaced parts are used.
10. The Goods are designed for domestic use only. A limited 90-day Warranty applies to any
industrial or commercial use of the Goods. The Goods must be connected to the electrical
voltage requirements as specified in the ratings label located on the Goods.
11. This warranty does not cover the cost of claiming under the warranty or transport of the
Goods to and from the Supplier or us.
12. This warranty is only valid and enforceable in Australia against Spectrum Brands
Australia Pty Ltd and in New Zealand against Spectrum Brands New Zealand Limited.
Contact us or the Supplier for further details.
Spectrum Brands Australia Pty Ltd
Chifley Business Park
1 Chifley Drive
Mentone, VIC 3194 Australia
Customer service in Australia: 1800 623 118
Website: www.remington-products.com.au
Spectrum Brands New Zealand Limited
Building C, Ground Floor
600 Great South Road,
Greenlane, Auckland 1051 New Zealand
Customer service in New Zealand: 0800 736 776
Website: www.remington-products.com.au
REMINGTON SERVICE HOTLINE
Australia 1800 623 118 (toll free)
New Zealand 0800 736 776 (toll free)
AUTHORISED REPAIR CENTRES
Visit www.remington-products.com.au for Authorised repair centre details.
® Registered Trademark of Spectrum Brands, Inc. (SBI), or one of its subsidiaries
Manufactured to Spectrum Brands specifications in the PRC
© 2012 SBI
Rev.05/12
Part No. T22-0000311
USE & CARE
MANUAL
PLEASE READ
PRIOR TO USE
TOOLS OF THE TRADE
FOIL SHAVER
This product is not suitable to use in a bath or shower.
The shaver conforms to radio frequency
interference requirements.
Anyproductpurchasedandusedcommercially
carries a limited 90 Day Warranty.
109
F3700AU_IFU_FA_170712.indd 1-7 17/07/12 11:42 AM
Trim
TO TRIM
1.Pull trimmer release button to
engage trimmer. (Diagram F)
2.Hold the trimmer at a right angle
to your skin.
3.Trim long, difficult hairs and side burns.
(Diagram G)
4. Close trimmer by pressing down.
(Diagram H)
MAINTENANCE
Cleaning & Care
NOTE: **When cleaning your shaver, make sure the shaver
is turned off and disconnected from the power cord.**
CAUTION!
Cleaning your shaver
To ensure long lasting performance, it is important to clean
your shaver regularly. We recommend you clean your
shaver after each use. The easiest and most hygienic way to
clean the shaver is by rinsing the shaver head after use with
warm water.
Weekly
Clean under the cutter assembly at least once a week:
1. Turn the shaver off.
2. Remove the head assembly from the shaver body (Diagram I).
4. Use your free hand to stretch your skin
so that the hairs stand upright. This
encourages your facial hair to stand out,
making it easier for them to enter the foil
and engage the intercept trimmer
(Diagram D).
5. Hold the shaver so that the foils touch
your skin simultaneously. The
independently floating screens
automatically adjust to the contours of
your face. Only apply light pressure on
the shaving head while shaving and use
short, circular strokes (Diagram E).
6.Aftershaving,turntheshaveroffby
sliding the power button.
Shaving Tips
For A Better Shave
For a smoother, more comfortable, moisture-free shave, use a
Remington® Pre-Shave Powder Stick (SP5).
**Remingtonrecommendsthatyouuseyournewshaver
dailyforuptothreeweekstoallowtimeforyourhairand
skintobecomeaccustomedtothenewshavingsystem**
• Ensureyourskinisdryandfreeofoils.
• Waitatleast15minutesaftergettingupbeforeshaving,
to ensure your face is free of puffiness that may be
present from sleeping.
• Alwaysholdtheshaveratarightangletotheskinsothat
both heads are touching the skin with equal pressure.
• Stretchskinwiththefreehandsohairsstandupright,
making it easier for them to enter the cutting chamber.
• Shavewithshort,circularstrokes.Theuseofshort,circular
motions in stubborn areas may obtain a closer shave,
especially along the neck and chin line.
• Donotpresshardagainsttheskininordertoavoid
damage to foil heads.
KEY PARTS
SPECIFICATIONS F3700AU
Power System Cordless (Rechargeable)
Initial Charge Time 24 hrs
Full Charge Time 16 hrs
Cordless Shave Time 40 min
Indicators Charging
Voltage Type Single Voltage
Replacement Part No. SP-62A
Power System:
Cordless – shaver can only be used without the power cord.
Indicators:
Charging – green light that glows when the shaver is being
charged.
Voltage Type:
Single Voltage – shaver can only be used with an outlet
voltage of 220-240V.
HOW TO USE
Adjusting To Your Shaver
Aswitheveryshaver,yourshavewillimproveovertime.Allow
up to four weeks of daily shaving to develop an effective
shaving style and for your skin to adjust to the new shaver. The
adaptation period may take a little longer if your skin is
sensitive, if you are switching from a different method of
shaving, or if you alternate between shaving methods.
Removing The Protective Head Guard
Before operating your shaver, remove the protective head
guard, which protects the foils and cutter assembly. It is
important to remove it correctly to avoid damaging the clips
that hold it to the shaver.
1. Press lightly on the top of the protective head guard.
2. Lift the lower rear edge.
F3700AU Tools of the Trade Foil Shaver
USE & CARE INSTRUCTIONMANUAL
Thank you for purchasing your new Remington® Tools of the
Trade Foil Shaver. Inside this manual you will find tips on using
and caring for your shaver.
1. Foils
2. Cutter assembly
3. Head release button
4. Hair pocket
5. Pop up trimmer (rear)
6. On/Off switch
7. Charging indicator
8. Power Port
Also includes:
Cleaning brush
Power adaptor
1
2
8
6
3
7
5
4
2
3456
3. Pull the protective head guard away from the shaver. When the
shaver is not in use, always keep the protective head guard on
the shaver head and keep the trimmer in the OFF position.
Charging
Beforeusing,readtheimportantsafetyinstructionsin
thismanual.
1. Ensure the product is switched off.
Connect the shaver to the adapter
(Diagram A).
2. Connect to the mains (Diagram B) and
charge for at least 24 hours when using
for the first time (Diagram C). This first
charge is important to the shaver’s
battery life.
3. When plugged, the charging indicator will
light up.
4. When empty, the battery should be
charged for 16 hours, and will provide
40 minutes of shaving time.
5. To preserve the life of the batteries, allow
them to fully discharge every six months,
and then recharge them for 24 hours.
CAUTION!
•
Make sure the shaver and your hands are dry when charging
the shaver.
•
Always charge the shaver in a cool, dry place.
SHAVING
To Shave
1.Removepoweradaptorfromtheshaver(DiagramA).
2. Slide the power button to activate the shaver for shaving.
3. Pull the trimmer release button to engage the trimmer, and use
it to remove long hair first. Then push trimmer downward to
lock it in when finished.
IMPORTANT SAFETY INSTRUCTIONS
When using an electric shaver, basic safety precautions should
always be observed, including the following.
Read all instructions before using this shaver.
KEEP POWER ADAPTOR AWAY FROM WATER
WARNING – TO REDUCE THE RISK OF BURNS, FIRE, ELECTRIC
SHOCK OR INJURY TO PERSONS:
• Theshavershouldneverbeleftunattendedwhenplugged
into a power outlet, except when charging the shaver.
• Thisappliancecanbeusedbychildrenagedfrom8years
and above and persons with reduced physical, sensory or
mentalcapabilitiesorlackofexperienceandknowledgeif
they have been given supervision or instruction concerning
use of the appliance in a safe way and understand the
hazards involved. Children shall not play with the appliance.
Cleaningandusermaintenanceshallnotbemadebychildren
without supervision.
• Usethisshaveronlyforitsintendeduseasdescribedinthis
manual.Donotuseattachmentsnotrecommendedby
Remington.
• Neveroperatethisshaverifithasadamagedcordorplug,if
itisnotworkingcorrectly,ifithasbeendroppedordamaged,
or dropped into water. If the supply cord or plug of this shaver
isdamageditmustbereplaced.Itcannotberepaired.
• Keepthecordawayfromheatedsurfaces.
• Charge,useandstoretheproductatatemperaturebetween
0°C and 32°C.
• Neverinsertanyobjectintoanyopeningofthisshaver.
• Donotuseoutdoorsorwhereaerosol(spray)productsare
beingused,orwhereoxygenisbeingadministered.
• Donotusetheshaverwithadamagedorbrokentracksor
cutters,asinjurymayoccur.
• Foruseonfacialhaironly.Notintendedforshavingthehair
on your head.
• Donotplugorunplugtheshaverwithwethands.
• Forhouseholduseonly.
RemingtonstronglyrecommendsthatanapprovedSafetySwitch
(residualcurrentdevice)beinstalledtoprotectallbathroom
poweroutlets.Askanelectricalcontractorforadvice
.
SAVE THESE INSTRUCTIONS
78
F3700AU_IFU_FA_170712.indd 8-14 17/07/12 11:42 AM
Trim
TO TRIM
1.Pull trimmer release button to
engage trimmer. (Diagram F)
2.Hold the trimmer at a right angle
to your skin.
3.Trim long, difficult hairs and side burns.
(Diagram G)
4. Close trimmer by pressing down.
(Diagram H)
MAINTENANCE
Cleaning & Care
NOTE: **When cleaning your shaver, make sure the shaver
is turned off and disconnected from the power cord.**
CAUTION!
Cleaning your shaver
To ensure long lasting performance, it is important to clean
your shaver regularly. We recommend you clean your
shaver after each use. The easiest and most hygienic way to
clean the shaver is by rinsing the shaver head after use with
warm water.
Weekly
Clean under the cutter assembly at least once a week:
1. Turn the shaver off.
2. Remove the head assembly from the shaver body (Diagram I).
4. Use your free hand to stretch your skin
so that the hairs stand upright. This
encourages your facial hair to stand out,
making it easier for them to enter the foil
and engage the intercept trimmer
(Diagram D).
5. Hold the shaver so that the foils touch
your skin simultaneously. The
independently floating screens
automatically adjust to the contours of
your face. Only apply light pressure on
the shaving head while shaving and use
short, circular strokes (Diagram E).
6.Aftershaving,turntheshaveroffby
sliding the power button.
Shaving Tips
For A Better Shave
For a smoother, more comfortable, moisture-free shave, use a
Remington® Pre-Shave Powder Stick (SP5).
**Remingtonrecommendsthatyouuseyournewshaver
dailyforuptothreeweekstoallowtimeforyourhairand
skintobecomeaccustomedtothenewshavingsystem**
• Ensureyourskinisdryandfreeofoils.
• Waitatleast15minutesaftergettingupbeforeshaving,
to ensure your face is free of puffiness that may be
present from sleeping.
• Alwaysholdtheshaveratarightangletotheskinsothat
both heads are touching the skin with equal pressure.
• Stretchskinwiththefreehandsohairsstandupright,
making it easier for them to enter the cutting chamber.
• Shavewithshort,circularstrokes.Theuseofshort,circular
motions in stubborn areas may obtain a closer shave,
especially along the neck and chin line.
• Donotpresshardagainsttheskininordertoavoid
damage to foil heads.
KEY PARTS
SPECIFICATIONS F3700AU
Power System Cordless (Rechargeable)
Initial Charge Time 24 hrs
Full Charge Time 16 hrs
Cordless Shave Time 40 min
Indicators Charging
Voltage Type Single Voltage
Replacement Part No. SP-62A
Power System:
Cordless – shaver can only be used without the power cord.
Indicators:
Charging – green light that glows when the shaver is being
charged.
Voltage Type:
Single Voltage – shaver can only be used with an outlet
voltage of 220-240V.
HOW TO USE
Adjusting To Your Shaver
Aswitheveryshaver,yourshavewillimproveovertime.Allow
up to four weeks of daily shaving to develop an effective
shaving style and for your skin to adjust to the new shaver. The
adaptation period may take a little longer if your skin is
sensitive, if you are switching from a different method of
shaving, or if you alternate between shaving methods.
Removing The Protective Head Guard
Before operating your shaver, remove the protective head
guard, which protects the foils and cutter assembly. It is
important to remove it correctly to avoid damaging the clips
that hold it to the shaver.
1. Press lightly on the top of the protective head guard.
2. Lift the lower rear edge.
F3700AU Tools of the Trade Foil Shaver
USE & CARE INSTRUCTIONMANUAL
Thank you for purchasing your new Remington® Tools of the
Trade Foil Shaver. Inside this manual you will find tips on using
and caring for your shaver.
1. Foils
2. Cutter assembly
3. Head release button
4. Hair pocket
5. Pop up trimmer (rear)
6. On/Off switch
7. Charging indicator
8. Power Port
Also includes:
Cleaning brush
Power adaptor
1
2
8
6
3
7
5
4
2
3
456
3. Pull the protective head guard away from the shaver. When the
shaver is not in use, always keep the protective head guard on
the shaver head and keep the trimmer in the OFF position.
Charging
Beforeusing,readtheimportantsafetyinstructionsin
thismanual.
1. Ensure the product is switched off.
Connect the shaver to the adapter
(Diagram A).
2. Connect to the mains (Diagram B) and
charge for at least 24 hours when using
for the first time (Diagram C). This first
charge is important to the shaver’s
battery life.
3. When plugged, the charging indicator will
light up.
4. When empty, the battery should be
charged for 16 hours, and will provide
40 minutes of shaving time.
5. To preserve the life of the batteries, allow
them to fully discharge every six months,
and then recharge them for 24 hours.
CAUTION!
•
Make sure the shaver and your hands are dry when charging
the shaver.
•
Always charge the shaver in a cool, dry place.
SHAVING
To Shave
1.Removepoweradaptorfromtheshaver(DiagramA).
2. Slide the power button to activate the shaver for shaving.
3. Pull the trimmer release button to engage the trimmer, and use
it to remove long hair first. Then push trimmer downward to
lock it in when finished.
IMPORTANT SAFETY INSTRUCTIONS
When using an electric shaver, basic safety precautions should
always be observed, including the following.
Read all instructions before using this shaver.
KEEP POWER ADAPTOR AWAY FROM WATER
WARNING – TO REDUCE THE RISK OF BURNS, FIRE, ELECTRIC
SHOCK OR INJURY TO PERSONS:
• Theshavershouldneverbeleftunattendedwhenplugged
into a power outlet, except when charging the shaver.
• Thisappliancecanbeusedbychildrenagedfrom8years
and above and persons with reduced physical, sensory or
mentalcapabilitiesorlackofexperienceandknowledgeif
they have been given supervision or instruction concerning
use of the appliance in a safe way and understand the
hazards involved. Children shall not play with the appliance.
Cleaningandusermaintenanceshallnotbemadebychildren
without supervision.
• Usethisshaveronlyforitsintendeduseasdescribedinthis
manual.Donotuseattachmentsnotrecommendedby
Remington.
• Neveroperatethisshaverifithasadamagedcordorplug,if
itisnotworkingcorrectly,ifithasbeendroppedordamaged,
or dropped into water. If the supply cord or plug of this shaver
isdamageditmustbereplaced.Itcannotberepaired.
• Keepthecordawayfromheatedsurfaces.
• Charge,useandstoretheproductatatemperaturebetween
0°C and 32°C.
• Neverinsertanyobjectintoanyopeningofthisshaver.
• Donotuseoutdoorsorwhereaerosol(spray)productsare
beingused,orwhereoxygenisbeingadministered.
• Donotusetheshaverwithadamagedorbrokentracksor
cutters,asinjurymayoccur.
• Foruseonfacialhaironly.Notintendedforshavingthehair
on your head.
• Donotplugorunplugtheshaverwithwethands.
• Forhouseholduseonly.
RemingtonstronglyrecommendsthatanapprovedSafetySwitch
(residualcurrentdevice)beinstalledtoprotectallbathroom
poweroutlets.Askanelectricalcontractorforadvice
.
SAVE THESE INSTRUCTIONS
78
F3700AU_IFU_FA_170712.indd 8-14 17/07/12 11:42 AM
Trim
TO TRIM
1.Pull trimmer release button to
engage trimmer. (Diagram F)
2.Hold the trimmer at a right angle
to your skin.
3.Trim long, difficult hairs and side burns.
(Diagram G)
4. Close trimmer by pressing down.
(Diagram H)
MAINTENANCE
Cleaning & Care
NOTE: **When cleaning your shaver, make sure the shaver
is turned off and disconnected from the power cord.**
CAUTION!
Cleaning your shaver
To ensure long lasting performance, it is important to clean
your shaver regularly. We recommend you clean your
shaver after each use. The easiest and most hygienic way to
clean the shaver is by rinsing the shaver head after use with
warm water.
Weekly
Clean under the cutter assembly at least once a week:
1. Turn the shaver off.
2. Remove the head assembly from the shaver body (Diagram I).
4. Use your free hand to stretch your skin
so that the hairs stand upright. This
encourages your facial hair to stand out,
making it easier for them to enter the foil
and engage the intercept trimmer
(Diagram D).
5. Hold the shaver so that the foils touch
your skin simultaneously. The
independently floating screens
automatically adjust to the contours of
your face. Only apply light pressure on
the shaving head while shaving and use
short, circular strokes (Diagram E).
6.Aftershaving,turntheshaveroffby
sliding the power button.
Shaving Tips
For A Better Shave
For a smoother, more comfortable, moisture-free shave, use a
Remington® Pre-Shave Powder Stick (SP5).
**Remingtonrecommendsthatyouuseyournewshaver
dailyforuptothreeweekstoallowtimeforyourhairand
skintobecomeaccustomedtothenewshavingsystem**
• Ensureyourskinisdryandfreeofoils.
• Waitatleast15minutesaftergettingupbeforeshaving,
to ensure your face is free of puffiness that may be
present from sleeping.
• Alwaysholdtheshaveratarightangletotheskinsothat
both heads are touching the skin with equal pressure.
• Stretchskinwiththefreehandsohairsstandupright,
making it easier for them to enter the cutting chamber.
• Shavewithshort,circularstrokes.Theuseofshort,circular
motions in stubborn areas may obtain a closer shave,
especially along the neck and chin line.
• Donotpresshardagainsttheskininordertoavoid
damage to foil heads.
KEY PARTS
SPECIFICATIONS F3700AU
Power System Cordless (Rechargeable)
Initial Charge Time 24 hrs
Full Charge Time 16 hrs
Cordless Shave Time 40 min
Indicators Charging
Voltage Type Single Voltage
Replacement Part No. SP-62A
Power System:
Cordless – shaver can only be used without the power cord.
Indicators:
Charging – green light that glows when the shaver is being
charged.
Voltage Type:
Single Voltage – shaver can only be used with an outlet
voltage of 220-240V.
HOW TO USE
Adjusting To Your Shaver
Aswitheveryshaver,yourshavewillimproveovertime.Allow
up to four weeks of daily shaving to develop an effective
shaving style and for your skin to adjust to the new shaver. The
adaptation period may take a little longer if your skin is
sensitive, if you are switching from a different method of
shaving, or if you alternate between shaving methods.
Removing The Protective Head Guard
Before operating your shaver, remove the protective head
guard, which protects the foils and cutter assembly. It is
important to remove it correctly to avoid damaging the clips
that hold it to the shaver.
1. Press lightly on the top of the protective head guard.
2. Lift the lower rear edge.
F3700AU Tools of the Trade Foil Shaver
USE & CARE INSTRUCTIONMANUAL
Thank you for purchasing your new Remington® Tools of the
Trade Foil Shaver. Inside this manual you will find tips on using
and caring for your shaver.
1. Foils
2. Cutter assembly
3. Head release button
4. Hair pocket
5. Pop up trimmer (rear)
6. On/Off switch
7. Charging indicator
8. Power Port
Also includes:
Cleaning brush
Power adaptor
1
2
8
6
3
7
5
4
2 3
4
5 6
3. Pull the protective head guard away from the shaver. When the
shaver is not in use, always keep the protective head guard on
the shaver head and keep the trimmer in the OFF position.
Charging
Beforeusing,readtheimportantsafetyinstructionsin
thismanual.
1. Ensure the product is switched off.
Connect the shaver to the adapter
(Diagram A).
2. Connect to the mains (Diagram B) and
charge for at least 24 hours when using
for the first time (Diagram C). This first
charge is important to the shaver’s
battery life.
3. When plugged, the charging indicator will
light up.
4. When empty, the battery should be
charged for 16 hours, and will provide
40 minutes of shaving time.
5. To preserve the life of the batteries, allow
them to fully discharge every six months,
and then recharge them for 24 hours.
CAUTION!
•
Make sure the shaver and your hands are dry when charging
the shaver.
•
Always charge the shaver in a cool, dry place.
SHAVING
To Shave
1.Removepoweradaptorfromtheshaver(DiagramA).
2. Slide the power button to activate the shaver for shaving.
3. Pull the trimmer release button to engage the trimmer, and use
it to remove long hair first. Then push trimmer downward to
lock it in when finished.
IMPORTANT SAFETY INSTRUCTIONS
When using an electric shaver, basic safety precautions should
always be observed, including the following.
Read all instructions before using this shaver.
KEEP POWER ADAPTOR AWAY FROM WATER
WARNING – TO REDUCE THE RISK OF BURNS, FIRE, ELECTRIC
SHOCK OR INJURY TO PERSONS:
• Theshavershouldneverbeleftunattendedwhenplugged
into a power outlet, except when charging the shaver.
• Thisappliancecanbeusedbychildrenagedfrom8years
and above and persons with reduced physical, sensory or
mentalcapabilitiesorlackofexperienceandknowledgeif
they have been given supervision or instruction concerning
use of the appliance in a safe way and understand the
hazards involved. Children shall not play with the appliance.
Cleaningandusermaintenanceshallnotbemadebychildren
without supervision.
• Usethisshaveronlyforitsintendeduseasdescribedinthis
manual.Donotuseattachmentsnotrecommendedby
Remington.
• Neveroperatethisshaverifithasadamagedcordorplug,if
itisnotworkingcorrectly,ifithasbeendroppedordamaged,
or dropped into water. If the supply cord or plug of this shaver
isdamageditmustbereplaced.Itcannotberepaired.
• Keepthecordawayfromheatedsurfaces.
• Charge,useandstoretheproductatatemperaturebetween
0°C and 32°C.
• Neverinsertanyobjectintoanyopeningofthisshaver.
• Donotuseoutdoorsorwhereaerosol(spray)productsare
beingused,orwhereoxygenisbeingadministered.
• Donotusetheshaverwithadamagedorbrokentracksor
cutters,asinjurymayoccur.
• Foruseonfacialhaironly.Notintendedforshavingthehair
on your head.
• Donotplugorunplugtheshaverwithwethands.
• Forhouseholduseonly.
RemingtonstronglyrecommendsthatanapprovedSafetySwitch
(residualcurrentdevice)beinstalledtoprotectallbathroom
poweroutlets.Askanelectricalcontractorforadvice
.
SAVE THESE INSTRUCTIONS
78
F3700AU_IFU_FA_170712.indd 8-14 17/07/12 11:42 AM
Trim
TO TRIM
1.Pull trimmer release button to
engage trimmer. (Diagram F)
2.Hold the trimmer at a right angle
to your skin.
3.Trim long, difficult hairs and side burns.
(Diagram G)
4. Close trimmer by pressing down.
(Diagram H)
MAINTENANCE
Cleaning & Care
NOTE: **When cleaning your shaver, make sure the shaver
is turned off and disconnected from the power cord.**
CAUTION!
Cleaning your shaver
To ensure long lasting performance, it is important to clean
your shaver regularly. We recommend you clean your
shaver after each use. The easiest and most hygienic way to
clean the shaver is by rinsing the shaver head after use with
warm water.
Weekly
Clean under the cutter assembly at least once a week:
1. Turn the shaver off.
2. Remove the head assembly from the shaver body (Diagram I).
4. Use your free hand to stretch your skin
so that the hairs stand upright. This
encourages your facial hair to stand out,
making it easier for them to enter the foil
and engage the intercept trimmer
(Diagram D).
5. Hold the shaver so that the foils touch
your skin simultaneously. The
independently floating screens
automatically adjust to the contours of
your face. Only apply light pressure on
the shaving head while shaving and use
short, circular strokes (Diagram E).
6.Aftershaving,turntheshaveroffby
sliding the power button.
Shaving Tips
For A Better Shave
For a smoother, more comfortable, moisture-free shave, use a
Remington® Pre-Shave Powder Stick (SP5).
**Remingtonrecommendsthatyouuseyournewshaver
dailyforuptothreeweekstoallowtimeforyourhairand
skintobecomeaccustomedtothenewshavingsystem**
• Ensureyourskinisdryandfreeofoils.
• Waitatleast15minutesaftergettingupbeforeshaving,
to ensure your face is free of puffiness that may be
present from sleeping.
• Alwaysholdtheshaveratarightangletotheskinsothat
both heads are touching the skin with equal pressure.
• Stretchskinwiththefreehandsohairsstandupright,
making it easier for them to enter the cutting chamber.
• Shavewithshort,circularstrokes.Theuseofshort,circular
motions in stubborn areas may obtain a closer shave,
especially along the neck and chin line.
• Donotpresshardagainsttheskininordertoavoid
damage to foil heads.
KEY PARTS
SPECIFICATIONS F3700AU
Power System Cordless (Rechargeable)
Initial Charge Time 24 hrs
Full Charge Time 16 hrs
Cordless Shave Time 40 min
Indicators Charging
Voltage Type Single Voltage
Replacement Part No. SP-62A
Power System:
Cordless – shaver can only be used without the power cord.
Indicators:
Charging – green light that glows when the shaver is being
charged.
Voltage Type:
Single Voltage – shaver can only be used with an outlet
voltage of 220-240V.
HOW TO USE
Adjusting To Your Shaver
Aswitheveryshaver,yourshavewillimproveovertime.Allow
up to four weeks of daily shaving to develop an effective
shaving style and for your skin to adjust to the new shaver. The
adaptation period may take a little longer if your skin is
sensitive, if you are switching from a different method of
shaving, or if you alternate between shaving methods.
Removing The Protective Head Guard
Before operating your shaver, remove the protective head
guard, which protects the foils and cutter assembly. It is
important to remove it correctly to avoid damaging the clips
that hold it to the shaver.
1. Press lightly on the top of the protective head guard.
2. Lift the lower rear edge.
F3700AU Tools of the Trade Foil Shaver
USE & CARE INSTRUCTIONMANUAL
Thank you for purchasing your new Remington® Tools of the
Trade Foil Shaver. Inside this manual you will find tips on using
and caring for your shaver.
1. Foils
2. Cutter assembly
3. Head release button
4. Hair pocket
5. Pop up trimmer (rear)
6. On/Off switch
7. Charging indicator
8. Power Port
Also includes:
Cleaning brush
Power adaptor
1
2
8
6
3
7
5
4
234
5
6
3. Pull the protective head guard away from the shaver. When the
shaver is not in use, always keep the protective head guard on
the shaver head and keep the trimmer in the OFF position.
Charging
Beforeusing,readtheimportantsafetyinstructionsin
thismanual.
1. Ensure the product is switched off.
Connect the shaver to the adapter
(Diagram A).
2. Connect to the mains (Diagram B) and
charge for at least 24 hours when using
for the first time (Diagram C). This first
charge is important to the shaver’s
battery life.
3. When plugged, the charging indicator will
light up.
4. When empty, the battery should be
charged for 16 hours, and will provide
40 minutes of shaving time.
5. To preserve the life of the batteries, allow
them to fully discharge every six months,
and then recharge them for 24 hours.
CAUTION!
•
Make sure the shaver and your hands are dry when charging
the shaver.
•
Always charge the shaver in a cool, dry place.
SHAVING
To Shave
1.Removepoweradaptorfromtheshaver(DiagramA).
2. Slide the power button to activate the shaver for shaving.
3. Pull the trimmer release button to engage the trimmer, and use
it to remove long hair first. Then push trimmer downward to
lock it in when finished.
IMPORTANT SAFETY INSTRUCTIONS
When using an electric shaver, basic safety precautions should
always be observed, including the following.
Read all instructions before using this shaver.
KEEP POWER ADAPTOR AWAY FROM WATER
WARNING – TO REDUCE THE RISK OF BURNS, FIRE, ELECTRIC
SHOCK OR INJURY TO PERSONS:
• Theshavershouldneverbeleftunattendedwhenplugged
into a power outlet, except when charging the shaver.
• Thisappliancecanbeusedbychildrenagedfrom8years
and above and persons with reduced physical, sensory or
mentalcapabilitiesorlackofexperienceandknowledgeif
they have been given supervision or instruction concerning
use of the appliance in a safe way and understand the
hazards involved. Children shall not play with the appliance.
Cleaningandusermaintenanceshallnotbemadebychildren
without supervision.
• Usethisshaveronlyforitsintendeduseasdescribedinthis
manual.Donotuseattachmentsnotrecommendedby
Remington.
• Neveroperatethisshaverifithasadamagedcordorplug,if
itisnotworkingcorrectly,ifithasbeendroppedordamaged,
or dropped into water. If the supply cord or plug of this shaver
isdamageditmustbereplaced.Itcannotberepaired.
• Keepthecordawayfromheatedsurfaces.
• Charge,useandstoretheproductatatemperaturebetween
0°C and 32°C.
• Neverinsertanyobjectintoanyopeningofthisshaver.
• Donotuseoutdoorsorwhereaerosol(spray)productsare
beingused,orwhereoxygenisbeingadministered.
• Donotusetheshaverwithadamagedorbrokentracksor
cutters,asinjurymayoccur.
• Foruseonfacialhaironly.Notintendedforshavingthehair
on your head.
• Donotplugorunplugtheshaverwithwethands.
• Forhouseholduseonly.
RemingtonstronglyrecommendsthatanapprovedSafetySwitch
(residualcurrentdevice)beinstalledtoprotectallbathroom
poweroutlets.Askanelectricalcontractorforadvice
.
SAVE THESE INSTRUCTIONS
78
F3700AU_IFU_FA_170712.indd 8-14 17/07/12 11:42 AM
Trim
TO TRIM
1.Pull trimmer release button to
engage trimmer. (Diagram F)
2.Hold the trimmer at a right angle
to your skin.
3.Trim long, difficult hairs and side burns.
(Diagram G)
4. Close trimmer by pressing down.
(Diagram H)
MAINTENANCE
Cleaning & Care
NOTE: **When cleaning your shaver, make sure the shaver
is turned off and disconnected from the power cord.**
CAUTION!
Cleaning your shaver
To ensure long lasting performance, it is important to clean
your shaver regularly. We recommend you clean your
shaver after each use. The easiest and most hygienic way to
clean the shaver is by rinsing the shaver head after use with
warm water.
Weekly
Clean under the cutter assembly at least once a week:
1. Turn the shaver off.
2. Remove the head assembly from the shaver body (Diagram I).
4. Use your free hand to stretch your skin
so that the hairs stand upright. This
encourages your facial hair to stand out,
making it easier for them to enter the foil
and engage the intercept trimmer
(Diagram D).
5. Hold the shaver so that the foils touch
your skin simultaneously. The
independently floating screens
automatically adjust to the contours of
your face. Only apply light pressure on
the shaving head while shaving and use
short, circular strokes (Diagram E).
6.Aftershaving,turntheshaveroffby
sliding the power button.
Shaving Tips
For A Better Shave
For a smoother, more comfortable, moisture-free shave, use a
Remington® Pre-Shave Powder Stick (SP5).
**Remingtonrecommendsthatyouuseyournewshaver
dailyforuptothreeweekstoallowtimeforyourhairand
skintobecomeaccustomedtothenewshavingsystem**
• Ensureyourskinisdryandfreeofoils.
• Waitatleast15minutesaftergettingupbeforeshaving,
to ensure your face is free of puffiness that may be
present from sleeping.
• Alwaysholdtheshaveratarightangletotheskinsothat
both heads are touching the skin with equal pressure.
• Stretchskinwiththefreehandsohairsstandupright,
making it easier for them to enter the cutting chamber.
• Shavewithshort,circularstrokes.Theuseofshort,circular
motions in stubborn areas may obtain a closer shave,
especially along the neck and chin line.
• Donotpresshardagainsttheskininordertoavoid
damage to foil heads.
KEY PARTS
SPECIFICATIONS F3700AU
Power System Cordless (Rechargeable)
Initial Charge Time 24 hrs
Full Charge Time 16 hrs
Cordless Shave Time 40 min
Indicators Charging
Voltage Type Single Voltage
Replacement Part No. SP-62A
Power System:
Cordless – shaver can only be used without the power cord.
Indicators:
Charging – green light that glows when the shaver is being
charged.
Voltage Type:
Single Voltage – shaver can only be used with an outlet
voltage of 220-240V.
HOW TO USE
Adjusting To Your Shaver
Aswitheveryshaver,yourshavewillimproveovertime.Allow
up to four weeks of daily shaving to develop an effective
shaving style and for your skin to adjust to the new shaver. The
adaptation period may take a little longer if your skin is
sensitive, if you are switching from a different method of
shaving, or if you alternate between shaving methods.
Removing The Protective Head Guard
Before operating your shaver, remove the protective head
guard, which protects the foils and cutter assembly. It is
important to remove it correctly to avoid damaging the clips
that hold it to the shaver.
1. Press lightly on the top of the protective head guard.
2. Lift the lower rear edge.
F3700AU Tools of the Trade Foil Shaver
USE & CARE INSTRUCTIONMANUAL
Thank you for purchasing your new Remington® Tools of the
Trade Foil Shaver. Inside this manual you will find tips on using
and caring for your shaver.
1. Foils
2. Cutter assembly
3. Head release button
4. Hair pocket
5. Pop up trimmer (rear)
6. On/Off switch
7. Charging indicator
8. Power Port
Also includes:
Cleaning brush
Power adaptor
1
2
8
6
3
7
5
4
2345
6
3. Pull the protective head guard away from the shaver. When the
shaver is not in use, always keep the protective head guard on
the shaver head and keep the trimmer in the OFF position.
Charging
Beforeusing,readtheimportantsafetyinstructionsin
thismanual.
1. Ensure the product is switched off.
Connect the shaver to the adapter
(Diagram A).
2. Connect to the mains (Diagram B) and
charge for at least 24 hours when using
for the first time (Diagram C). This first
charge is important to the shaver’s
battery life.
3. When plugged, the charging indicator will
light up.
4. When empty, the battery should be
charged for 16 hours, and will provide
40 minutes of shaving time.
5. To preserve the life of the batteries, allow
them to fully discharge every six months,
and then recharge them for 24 hours.
CAUTION!
•
Make sure the shaver and your hands are dry when charging
the shaver.
•
Always charge the shaver in a cool, dry place.
SHAVING
To Shave
1.Removepoweradaptorfromtheshaver(DiagramA).
2. Slide the power button to activate the shaver for shaving.
3. Pull the trimmer release button to engage the trimmer, and use
it to remove long hair first. Then push trimmer downward to
lock it in when finished.
IMPORTANT SAFETY INSTRUCTIONS
When using an electric shaver, basic safety precautions should
always be observed, including the following.
Read all instructions before using this shaver.
KEEP POWER ADAPTOR AWAY FROM WATER
WARNING – TO REDUCE THE RISK OF BURNS, FIRE, ELECTRIC
SHOCK OR INJURY TO PERSONS:
• Theshavershouldneverbeleftunattendedwhenplugged
into a power outlet, except when charging the shaver.
• Thisappliancecanbeusedbychildrenagedfrom8years
and above and persons with reduced physical, sensory or
mentalcapabilitiesorlackofexperienceandknowledgeif
they have been given supervision or instruction concerning
use of the appliance in a safe way and understand the
hazards involved. Children shall not play with the appliance.
Cleaningandusermaintenanceshallnotbemadebychildren
without supervision.
• Usethisshaveronlyforitsintendeduseasdescribedinthis
manual.Donotuseattachmentsnotrecommendedby
Remington.
• Neveroperatethisshaverifithasadamagedcordorplug,if
itisnotworkingcorrectly,ifithasbeendroppedordamaged,
or dropped into water. If the supply cord or plug of this shaver
isdamageditmustbereplaced.Itcannotberepaired.
• Keepthecordawayfromheatedsurfaces.
• Charge,useandstoretheproductatatemperaturebetween
0°C and 32°C.
• Neverinsertanyobjectintoanyopeningofthisshaver.
• Donotuseoutdoorsorwhereaerosol(spray)productsare
beingused,orwhereoxygenisbeingadministered.
• Donotusetheshaverwithadamagedorbrokentracksor
cutters,asinjurymayoccur.
• Foruseonfacialhaironly.Notintendedforshavingthehair
on your head.
• Donotplugorunplugtheshaverwithwethands.
• Forhouseholduseonly.
RemingtonstronglyrecommendsthatanapprovedSafetySwitch
(residualcurrentdevice)beinstalledtoprotectallbathroom
poweroutlets.Askanelectricalcontractorforadvice
.
SAVE THESE INSTRUCTIONS
78
F3700AU_IFU_FA_170712.indd 8-14 17/07/12 11:42 AM
Trim
TO TRIM
1.Pull trimmer release button to
engage trimmer. (Diagram F)
2.Hold the trimmer at a right angle
to your skin.
3.Trim long, difficult hairs and side burns.
(Diagram G)
4. Close trimmer by pressing down.
(Diagram H)
MAINTENANCE
Cleaning & Care
NOTE: **When cleaning your shaver, make sure the shaver
is turned off and disconnected from the power cord.**
CAUTION!
Cleaning your shaver
To ensure long lasting performance, it is important to clean
your shaver regularly. We recommend you clean your
shaver after each use. The easiest and most hygienic way to
clean the shaver is by rinsing the shaver head after use with
warm water.
Weekly
Clean under the cutter assembly at least once a week:
1. Turn the shaver off.
2. Remove the head assembly from the shaver body (Diagram I).
4. Use your free hand to stretch your skin
so that the hairs stand upright. This
encourages your facial hair to stand out,
making it easier for them to enter the foil
and engage the intercept trimmer
(Diagram D).
5. Hold the shaver so that the foils touch
your skin simultaneously. The
independently floating screens
automatically adjust to the contours of
your face. Only apply light pressure on
the shaving head while shaving and use
short, circular strokes (Diagram E).
6.Aftershaving,turntheshaveroffby
sliding the power button.
Shaving Tips
For A Better Shave
For a smoother, more comfortable, moisture-free shave, use a
Remington® Pre-Shave Powder Stick (SP5).
**Remingtonrecommendsthatyouuseyournewshaver
dailyforuptothreeweekstoallowtimeforyourhairand
skintobecomeaccustomedtothenewshavingsystem**
• Ensureyourskinisdryandfreeofoils.
• Waitatleast15minutesaftergettingupbeforeshaving,
to ensure your face is free of puffiness that may be
present from sleeping.
• Alwaysholdtheshaveratarightangletotheskinsothat
both heads are touching the skin with equal pressure.
• Stretchskinwiththefreehandsohairsstandupright,
making it easier for them to enter the cutting chamber.
• Shavewithshort,circularstrokes.Theuseofshort,circular
motions in stubborn areas may obtain a closer shave,
especially along the neck and chin line.
• Donotpresshardagainsttheskininordertoavoid
damage to foil heads.
KEY PARTS
SPECIFICATIONS F3700AU
Power System Cordless (Rechargeable)
Initial Charge Time 24 hrs
Full Charge Time 16 hrs
Cordless Shave Time 40 min
Indicators Charging
Voltage Type Single Voltage
Replacement Part No. SP-62A
Power System:
Cordless – shaver can only be used without the power cord.
Indicators:
Charging – green light that glows when the shaver is being
charged.
Voltage Type:
Single Voltage – shaver can only be used with an outlet
voltage of 220-240V.
HOW TO USE
Adjusting To Your Shaver
Aswitheveryshaver,yourshavewillimproveovertime.Allow
up to four weeks of daily shaving to develop an effective
shaving style and for your skin to adjust to the new shaver. The
adaptation period may take a little longer if your skin is
sensitive, if you are switching from a different method of
shaving, or if you alternate between shaving methods.
Removing The Protective Head Guard
Before operating your shaver, remove the protective head
guard, which protects the foils and cutter assembly. It is
important to remove it correctly to avoid damaging the clips
that hold it to the shaver.
1. Press lightly on the top of the protective head guard.
2. Lift the lower rear edge.
F3700AU Tools of the Trade Foil Shaver
USE & CARE INSTRUCTIONMANUAL
Thank you for purchasing your new Remington® Tools of the
Trade Foil Shaver. Inside this manual you will find tips on using
and caring for your shaver.
1. Foils
2. Cutter assembly
3. Head release button
4. Hair pocket
5. Pop up trimmer (rear)
6. On/Off switch
7. Charging indicator
8. Power Port
Also includes:
Cleaning brush
Power adaptor
1
2
8
6
3
7
5
4
23456
3. Pull the protective head guard away from the shaver. When the
shaver is not in use, always keep the protective head guard on
the shaver head and keep the trimmer in the OFF position.
Charging
Beforeusing,readtheimportantsafetyinstructionsin
thismanual.
1. Ensure the product is switched off.
Connect the shaver to the adapter
(Diagram A).
2. Connect to the mains (Diagram B) and
charge for at least 24 hours when using
for the first time (Diagram C). This first
charge is important to the shaver’s
battery life.
3. When plugged, the charging indicator will
light up.
4. When empty, the battery should be
charged for 16 hours, and will provide
40 minutes of shaving time.
5. To preserve the life of the batteries, allow
them to fully discharge every six months,
and then recharge them for 24 hours.
CAUTION!
•
Make sure the shaver and your hands are dry when charging
the shaver.
•
Always charge the shaver in a cool, dry place.
SHAVING
To Shave
1.Removepoweradaptorfromtheshaver(DiagramA).
2. Slide the power button to activate the shaver for shaving.
3. Pull the trimmer release button to engage the trimmer, and use
it to remove long hair first. Then push trimmer downward to
lock it in when finished.
IMPORTANT SAFETY INSTRUCTIONS
When using an electric shaver, basic safety precautions should
always be observed, including the following.
Read all instructions before using this shaver.
KEEP POWER ADAPTOR AWAY FROM WATER
WARNING – TO REDUCE THE RISK OF BURNS, FIRE, ELECTRIC
SHOCK OR INJURY TO PERSONS:
• Theshavershouldneverbeleftunattendedwhenplugged
into a power outlet, except when charging the shaver.
• Thisappliancecanbeusedbychildrenagedfrom8years
and above and persons with reduced physical, sensory or
mentalcapabilitiesorlackofexperienceandknowledgeif
they have been given supervision or instruction concerning
use of the appliance in a safe way and understand the
hazards involved. Children shall not play with the appliance.
Cleaningandusermaintenanceshallnotbemadebychildren
without supervision.
• Usethisshaveronlyforitsintendeduseasdescribedinthis
manual.Donotuseattachmentsnotrecommendedby
Remington.
• Neveroperatethisshaverifithasadamagedcordorplug,if
itisnotworkingcorrectly,ifithasbeendroppedordamaged,
or dropped into water. If the supply cord or plug of this shaver
isdamageditmustbereplaced.Itcannotberepaired.
• Keepthecordawayfromheatedsurfaces.
• Charge,useandstoretheproductatatemperaturebetween
0°C and 32°C.
• Neverinsertanyobjectintoanyopeningofthisshaver.
• Donotuseoutdoorsorwhereaerosol(spray)productsare
beingused,orwhereoxygenisbeingadministered.
• Donotusetheshaverwithadamagedorbrokentracksor
cutters,asinjurymayoccur.
• Foruseonfacialhaironly.Notintendedforshavingthehair
on your head.
• Donotplugorunplugtheshaverwithwethands.
• Forhouseholduseonly.
RemingtonstronglyrecommendsthatanapprovedSafetySwitch
(residualcurrentdevice)beinstalledtoprotectallbathroom
poweroutlets.Askanelectricalcontractorforadvice
.
SAVE THESE INSTRUCTIONS
7
8
F3700AU_IFU_FA_170712.indd 8-14 17/07/12 11:42 AM
Trim
TO TRIM
1.Pull trimmer release button to
engage trimmer. (Diagram F)
2.Hold the trimmer at a right angle
to your skin.
3.Trim long, difficult hairs and side burns.
(Diagram G)
4. Close trimmer by pressing down.
(Diagram H)
MAINTENANCE
Cleaning & Care
NOTE: **When cleaning your shaver, make sure the shaver
is turned off and disconnected from the power cord.**
CAUTION!
Cleaning your shaver
To ensure long lasting performance, it is important to clean
your shaver regularly. We recommend you clean your
shaver after each use. The easiest and most hygienic way to
clean the shaver is by rinsing the shaver head after use with
warm water.
Weekly
Clean under the cutter assembly at least once a week:
1. Turn the shaver off.
2. Remove the head assembly from the shaver body (Diagram I).
4. Use your free hand to stretch your skin
so that the hairs stand upright. This
encourages your facial hair to stand out,
making it easier for them to enter the foil
and engage the intercept trimmer
(Diagram D).
5. Hold the shaver so that the foils touch
your skin simultaneously. The
independently floating screens
automatically adjust to the contours of
your face. Only apply light pressure on
the shaving head while shaving and use
short, circular strokes (Diagram E).
6.Aftershaving,turntheshaveroffby
sliding the power button.
Shaving Tips
For A Better Shave
For a smoother, more comfortable, moisture-free shave, use a
Remington® Pre-Shave Powder Stick (SP5).
**Remingtonrecommendsthatyouuseyournewshaver
dailyforuptothreeweekstoallowtimeforyourhairand
skintobecomeaccustomedtothenewshavingsystem**
• Ensureyourskinisdryandfreeofoils.
• Waitatleast15minutesaftergettingupbeforeshaving,
to ensure your face is free of puffiness that may be
present from sleeping.
• Alwaysholdtheshaveratarightangletotheskinsothat
both heads are touching the skin with equal pressure.
• Stretchskinwiththefreehandsohairsstandupright,
making it easier for them to enter the cutting chamber.
• Shavewithshort,circularstrokes.Theuseofshort,circular
motions in stubborn areas may obtain a closer shave,
especially along the neck and chin line.
• Donotpresshardagainsttheskininordertoavoid
damage to foil heads.
KEY PARTS
SPECIFICATIONS F3700AU
Power System Cordless (Rechargeable)
Initial Charge Time 24 hrs
Full Charge Time 16 hrs
Cordless Shave Time 40 min
Indicators Charging
Voltage Type Single Voltage
Replacement Part No. SP-62A
Power System:
Cordless – shaver can only be used without the power cord.
Indicators:
Charging – green light that glows when the shaver is being
charged.
Voltage Type:
Single Voltage – shaver can only be used with an outlet
voltage of 220-240V.
HOW TO USE
Adjusting To Your Shaver
Aswitheveryshaver,yourshavewillimproveovertime.Allow
up to four weeks of daily shaving to develop an effective
shaving style and for your skin to adjust to the new shaver. The
adaptation period may take a little longer if your skin is
sensitive, if you are switching from a different method of
shaving, or if you alternate between shaving methods.
Removing The Protective Head Guard
Before operating your shaver, remove the protective head
guard, which protects the foils and cutter assembly. It is
important to remove it correctly to avoid damaging the clips
that hold it to the shaver.
1. Press lightly on the top of the protective head guard.
2. Lift the lower rear edge.
F3700AU Tools of the Trade Foil Shaver
USE & CARE INSTRUCTIONMANUAL
Thank you for purchasing your new Remington® Tools of the
Trade Foil Shaver. Inside this manual you will find tips on using
and caring for your shaver.
1. Foils
2. Cutter assembly
3. Head release button
4. Hair pocket
5. Pop up trimmer (rear)
6. On/Off switch
7. Charging indicator
8. Power Port
Also includes:
Cleaning brush
Power adaptor
1
2
8
6
3
7
5
4
23456
3. Pull the protective head guard away from the shaver. When the
shaver is not in use, always keep the protective head guard on
the shaver head and keep the trimmer in the OFF position.
Charging
Beforeusing,readtheimportantsafetyinstructionsin
thismanual.
1. Ensure the product is switched off.
Connect the shaver to the adapter
(Diagram A).
2. Connect to the mains (Diagram B) and
charge for at least 24 hours when using
for the first time (Diagram C). This first
charge is important to the shaver’s
battery life.
3. When plugged, the charging indicator will
light up.
4. When empty, the battery should be
charged for 16 hours, and will provide
40 minutes of shaving time.
5. To preserve the life of the batteries, allow
them to fully discharge every six months,
and then recharge them for 24 hours.
CAUTION!
•
Make sure the shaver and your hands are dry when charging
the shaver.
•
Always charge the shaver in a cool, dry place.
SHAVING
To Shave
1.Removepoweradaptorfromtheshaver(DiagramA).
2. Slide the power button to activate the shaver for shaving.
3. Pull the trimmer release button to engage the trimmer, and use
it to remove long hair first. Then push trimmer downward to
lock it in when finished.
IMPORTANT SAFETY INSTRUCTIONS
When using an electric shaver, basic safety precautions should
always be observed, including the following.
Read all instructions before using this shaver.
KEEP POWER ADAPTOR AWAY FROM WATER
WARNING – TO REDUCE THE RISK OF BURNS, FIRE, ELECTRIC
SHOCK OR INJURY TO PERSONS:
• Theshavershouldneverbeleftunattendedwhenplugged
into a power outlet, except when charging the shaver.
• Thisappliancecanbeusedbychildrenagedfrom8years
and above and persons with reduced physical, sensory or
mentalcapabilitiesorlackofexperienceandknowledgeif
they have been given supervision or instruction concerning
use of the appliance in a safe way and understand the
hazards involved. Children shall not play with the appliance.
Cleaningandusermaintenanceshallnotbemadebychildren
without supervision.
• Usethisshaveronlyforitsintendeduseasdescribedinthis
manual.Donotuseattachmentsnotrecommendedby
Remington.
• Neveroperatethisshaverifithasadamagedcordorplug,if
itisnotworkingcorrectly,ifithasbeendroppedordamaged,
or dropped into water. If the supply cord or plug of this shaver
isdamageditmustbereplaced.Itcannotberepaired.
• Keepthecordawayfromheatedsurfaces.
• Charge,useandstoretheproductatatemperaturebetween
0°C and 32°C.
• Neverinsertanyobjectintoanyopeningofthisshaver.
• Donotuseoutdoorsorwhereaerosol(spray)productsare
beingused,orwhereoxygenisbeingadministered.
• Donotusetheshaverwithadamagedorbrokentracksor
cutters,asinjurymayoccur.
• Foruseonfacialhaironly.Notintendedforshavingthehair
on your head.
• Donotplugorunplugtheshaverwithwethands.
• Forhouseholduseonly.
RemingtonstronglyrecommendsthatanapprovedSafetySwitch
(residualcurrentdevice)beinstalledtoprotectallbathroom
poweroutlets.Askanelectricalcontractorforadvice
.
SAVE THESE INSTRUCTIONS
7
8
F3700AU_IFU_FA_170712.indd 8-14 17/07/12 11:42 AM
3. Gently tap the shaver head on a flat surface to remove any
loose hair particles, and rinse the shaver head under warm
water (Diagram J). Never submerge your
shaver under water.
4. Thoroughly clean the cutter and trimmer
with a brush (Diagram J).
5. Never use the cleaning brush on the foils,
as damage may occur.
6. Shake off any excess water.
7. Leave the shave unit open to allow the
shaver to
dry completely.
8. Lubricate the shaver with a spray of
Remington® Shaver Saver (SP4) on the
foil and cutters.
9. Replace the head assembly, simply by
pushing it on the shaver.
Cover shaver head with the protective head guard between
uses. When removing the head guard or placing it back onto
the shaver, do not apply pressure to the floating cutter
surfaces, as you may damage them.
Lubricate
Remington® Shaver Saver (SP-4) lubricates, cleans and
protects your shaver’s foil and cutter assembly. The lubricant
helps remove hair clippings while reducing wear. Spray on the
foil and cutters after each shave to keep your shaver operating
at peak performance.
Cleaning Cautions
•Never submerge the shaver completely into water.
•Never clean the shaver or replace the cutters while it is
plugged into an electrical outlet.
•Do not use any aggressive cleaning agents, as this may
damage the shaver.
Replacing Your Heads & Cutters
It is very important to replace your foils and cutters when
necessary to ensure a close, comfortable shave without
I
J
irritation. We recommend they be replaced every 6 months for
optimal performance. Here are some signs of head and cutter
wear, indicating that replacement is needed.
Signs that your foils and cutters need replacing:
• Irritation:Asfoilsgetworn,youmayexperienceskinirritation.
Asthefoilsbecomeexcessivelywornyoumayexperience
some skin irritation or redness.
• Pulling:Asthecutterswear,yourshavemaynotfeelasclose
and you may feel your cutter pulling your hair.
• Wearthrough:Youmaynoticethatthecuttershaveworn
through the foils.
TO REPLACE THE FOIL
• Pullthefoilassemblyuptoremovefromthehairpocket.
• Insertnewfoilassemblyinhairpocketuntilitsnapsinplace.
TO REPLACE THE CUTTERS
• Graspcutterbetweenthumbandforefingerandpullupward.
• Snapbothnewcutterassembliesintotopofoscillatortips.
STORAGE
When not in use, always unplug the power adaptor from the
power outlet. Never wrap the cord of the power adaptor
around the unit as this will cause the cord to wear prematurely
and break. Handle the cord carefully for long life and avoid
jerking, twisting or straining especially at the power plug. If the
cord becomes twisted in use, periodically straighten it.
2 YEAR WARRANTY F3700AU
MONEY BACK OFFER - Australia/New Zealand Only
If within 30 days you are not fully satisfied with your
Remington® shaver, just return the shaver with this completed
couponandacopyofyourAustralian/NewZealandpurchase
receipt to Remington®. In return, we will send you a cheque for
the full purchase price of the shaver. Please allow 6-8 weeks
for your cheque to arrive.
Name:
Address:
City:
State: Postcode:
1211 13 14
Spectrum Brands Australia Pty Ltd and Spectrum Brands New Zealand Limited
WARRANTY AGAINST DEFECTS
In this warranty:
Australian Consumer Law means the Australian consumer law set out in Schedule 2
to the Competition and Consumer Act 2010;
CGA means the New Zealand Consumer Guarantees Act 1993;
Goods means the product or equipment which was accompanied by this warranty and
purchased in Australia or New Zealand, as the case may be;
Manufacturer, We or us means:
1. for Goods purchased in Australia, Spectrum Brands Australia Pty Ltd
ACN, 007 070 573; or
2. for Goods purchased in New Zealand, Spectrum Brands New Zealand Limited,
as the case may be, contact details as set out at the end of this warranty;
Supplier means the authorised distributor or retailer of the Goods that sold you the Goods
in Australia or in New Zealand; and
You means you, the original end-user purchaser of the Goods.
1. Our goods come with guarantees that cannot be excluded under the Australian
Consumer Law, or the CGA. You are entitled to a replacement or refund for a major failure
and compensation for any other reasonably foreseeable loss or damage. You are also
entitled to have the goods repaired or replaced if the goods fail to be of acceptable
quality and the failure does not amount to a major failure.
2. The benefits provided by this Warranty are in addition to all other rights and remedies in
respect of the Goods which the consumer has under either the Australian Consumer Law
or the CGA. The original purchaser of the Goods is provided with the following Warranty
subject to the Warranty Conditions:
3. We warrant the Goods for all parts defective in workmanship or materials for the period
of two (2) years from the date of purchase (Warranty Period). If the Goods prove
defective within the Warranty Period by reason of improper workmanship or material,
we may, at our own discretion, repair or replace the Goods without charge.
Warranty Conditions
4. The Goods must be used in accordance with the manufacturer’s instructions. This
Warranty does not apply should the defect in or failure of the Goods be attributable to
misuse, abuse, accident or non-observance of manufacturer’s instructions on the part of
the user. As far as the law permits, the manufacturer does not accept liability for any
direct or consequential loss, damage or other expense caused by or arising out of any
failure to use the Goods in accordance with the manufacturer’s instructions.
5. Exhaustible components (such as shaver heads, cutters and foils) of the Goods
are included under this Warranty only where there is a defect in workmanship or
materials used.
6. The warranty granted under clause 3 is limited to repair or replacement only.
7. Any parts of the Goods replaced during repairs or any product replaced remain the
property of the manufacturer. In the event of the Goods being replaced during the
Warranty Period, the warranty on the replacement Goods will expire on the same date
as for the Warranty Period on the original Goods which are replaced.
8. In order to claim under the warranty granted under clause 3 you must:
(a) Retain this warranty with your receipt/proof of purchase; and
(b) Return the Goods to us at the relevant address below or to the Supplier by prepaid
freight within the Warranty Period accompanied with (i) the legible and unmodified
original proof of purchase, which clearly indicates the name and address of the
Supplier, the date and place of purchase, the product name or other product serial
number and (ii) this warranty.
9. This warranty is immediately void if:
(a) Any serial number or appliance plate is removed or defaced;
(b) The Goods have been serviced or otherwise repaired by a person not authorised to
do so by us or where non approved replaced parts are used.
10. The Goods are designed for domestic use only. A limited 90-day Warranty applies to any
industrial or commercial use of the Goods. The Goods must be connected to the electrical
voltage requirements as specified in the ratings label located on the Goods.
11. This warranty does not cover the cost of claiming under the warranty or transport of the
Goods to and from the Supplier or us.
12. This warranty is only valid and enforceable in Australia against Spectrum Brands
Australia Pty Ltd and in New Zealand against Spectrum Brands New Zealand Limited.
Contact us or the Supplier for further details.
Spectrum Brands Australia Pty Ltd
Chifley Business Park
1 Chifley Drive
Mentone, VIC 3194 Australia
Customer service in Australia: 1800 623 118
Website: www.remington-products.com.au
Spectrum Brands New Zealand Limited
Building C, Ground Floor
600 Great South Road,
Greenlane, Auckland 1051 New Zealand
Customer service in New Zealand: 0800 736 776
Website: www.remington-products.com.au
REMINGTON SERVICE HOTLINE
Australia 1800 623 118 (toll free)
New Zealand 0800 736 776 (toll free)
AUTHORISED REPAIR CENTRES
Visit www.remington-products.com.au for Authorised repair centre details.
® Registered Trademark of Spectrum Brands, Inc. (SBI), or one of its subsidiaries
Manufactured to Spectrum Brands specifications in the PRC
© 2012 SBI
Rev.05/12
Part No. T22-0000311
USE & CARE
MANUAL
PLEASE READ
PRIOR TO USE
TOOLS OF THE TRADE
FOIL SHAVER
This product is not suitable to use in a bath or shower.
The shaver conforms to radio frequency
interference requirements.
Anyproductpurchasedandusedcommercially
carries a limited 90 Day Warranty.
10
9
F3700AU_IFU_FA_170712.indd 1-7 17/07/12 11:42 AM
3. Gently tap the shaver head on a flat surface to remove any
loose hair particles, and rinse the shaver head under warm
water (Diagram J). Never submerge your
shaver under water.
4. Thoroughly clean the cutter and trimmer
with a brush (Diagram J).
5. Never use the cleaning brush on the foils,
as damage may occur.
6. Shake off any excess water.
7. Leave the shave unit open to allow the
shaver to
dry completely.
8. Lubricate the shaver with a spray of
Remington® Shaver Saver (SP4) on the
foil and cutters.
9. Replace the head assembly, simply by
pushing it on the shaver.
Cover shaver head with the protective head guard between
uses. When removing the head guard or placing it back onto
the shaver, do not apply pressure to the floating cutter
surfaces, as you may damage them.
Lubricate
Remington® Shaver Saver (SP-4) lubricates, cleans and
protects your shaver’s foil and cutter assembly. The lubricant
helps remove hair clippings while reducing wear. Spray on the
foil and cutters after each shave to keep your shaver operating
at peak performance.
Cleaning Cautions
•Never submerge the shaver completely into water.
•Never clean the shaver or replace the cutters while it is
plugged into an electrical outlet.
•Do not use any aggressive cleaning agents, as this may
damage the shaver.
Replacing Your Heads & Cutters
It is very important to replace your foils and cutters when
necessary to ensure a close, comfortable shave without
I
J
irritation. We recommend they be replaced every 6 months for
optimal performance. Here are some signs of head and cutter
wear, indicating that replacement is needed.
Signs that your foils and cutters need replacing:
• Irritation:Asfoilsgetworn,youmayexperienceskinirritation.
Asthefoilsbecomeexcessivelywornyoumayexperience
some skin irritation or redness.
• Pulling:Asthecutterswear,yourshavemaynotfeelasclose
and you may feel your cutter pulling your hair.
• Wearthrough:Youmaynoticethatthecuttershaveworn
through the foils.
TO REPLACE THE FOIL
• Pullthefoilassemblyuptoremovefromthehairpocket.
• Insertnewfoilassemblyinhairpocketuntilitsnapsinplace.
TO REPLACE THE CUTTERS
• Graspcutterbetweenthumbandforefingerandpullupward.
• Snapbothnewcutterassembliesintotopofoscillatortips.
STORAGE
When not in use, always unplug the power adaptor from the
power outlet. Never wrap the cord of the power adaptor
around the unit as this will cause the cord to wear prematurely
and break. Handle the cord carefully for long life and avoid
jerking, twisting or straining especially at the power plug. If the
cord becomes twisted in use, periodically straighten it.
2 YEAR WARRANTY F3700AU
MONEY BACK OFFER - Australia/New Zealand Only
If within 30 days you are not fully satisfied with your
Remington® shaver, just return the shaver with this completed
couponandacopyofyourAustralian/NewZealandpurchase
receipt to Remington®. In return, we will send you a cheque for
the full purchase price of the shaver. Please allow 6-8 weeks
for your cheque to arrive.
Name:
Address:
City:
State: Postcode:
1211 13 14
Spectrum Brands Australia Pty Ltd and Spectrum Brands New Zealand Limited
WARRANTY AGAINST DEFECTS
In this warranty:
Australian Consumer Law means the Australian consumer law set out in Schedule 2
to the Competition and Consumer Act 2010;
CGA means the New Zealand Consumer Guarantees Act 1993;
Goods means the product or equipment which was accompanied by this warranty and
purchased in Australia or New Zealand, as the case may be;
Manufacturer, We or us means:
1. for Goods purchased in Australia, Spectrum Brands Australia Pty Ltd
ACN, 007 070 573; or
2. for Goods purchased in New Zealand, Spectrum Brands New Zealand Limited,
as the case may be, contact details as set out at the end of this warranty;
Supplier means the authorised distributor or retailer of the Goods that sold you the Goods
in Australia or in New Zealand; and
You means you, the original end-user purchaser of the Goods.
1. Our goods come with guarantees that cannot be excluded under the Australian
Consumer Law, or the CGA. You are entitled to a replacement or refund for a major failure
and compensation for any other reasonably foreseeable loss or damage. You are also
entitled to have the goods repaired or replaced if the goods fail to be of acceptable
quality and the failure does not amount to a major failure.
2. The benefits provided by this Warranty are in addition to all other rights and remedies in
respect of the Goods which the consumer has under either the Australian Consumer Law
or the CGA. The original purchaser of the Goods is provided with the following Warranty
subject to the Warranty Conditions:
3. We warrant the Goods for all parts defective in workmanship or materials for the period
of two (2) years from the date of purchase (Warranty Period). If the Goods prove
defective within the Warranty Period by reason of improper workmanship or material,
we may, at our own discretion, repair or replace the Goods without charge.
Warranty Conditions
4. The Goods must be used in accordance with the manufacturer’s instructions. This
Warranty does not apply should the defect in or failure of the Goods be attributable to
misuse, abuse, accident or non-observance of manufacturer’s instructions on the part of
the user. As far as the law permits, the manufacturer does not accept liability for any
direct or consequential loss, damage or other expense caused by or arising out of any
failure to use the Goods in accordance with the manufacturer’s instructions.
5. Exhaustible components (such as shaver heads, cutters and foils) of the Goods
are included under this Warranty only where there is a defect in workmanship or
materials used.
6. The warranty granted under clause 3 is limited to repair or replacement only.
7. Any parts of the Goods replaced during repairs or any product replaced remain the
property of the manufacturer. In the event of the Goods being replaced during the
Warranty Period, the warranty on the replacement Goods will expire on the same date
as for the Warranty Period on the original Goods which are replaced.
8. In order to claim under the warranty granted under clause 3 you must:
(a) Retain this warranty with your receipt/proof of purchase; and
(b) Return the Goods to us at the relevant address below or to the Supplier by prepaid
freight within the Warranty Period accompanied with (i) the legible and unmodified
original proof of purchase, which clearly indicates the name and address of the
Supplier, the date and place of purchase, the product name or other product serial
number and (ii) this warranty.
9. This warranty is immediately void if:
(a) Any serial number or appliance plate is removed or defaced;
(b) The Goods have been serviced or otherwise repaired by a person not authorised to
do so by us or where non approved replaced parts are used.
10. The Goods are designed for domestic use only. A limited 90-day Warranty applies to any
industrial or commercial use of the Goods. The Goods must be connected to the electrical
voltage requirements as specified in the ratings label located on the Goods.
11. This warranty does not cover the cost of claiming under the warranty or transport of the
Goods to and from the Supplier or us.
12. This warranty is only valid and enforceable in Australia against Spectrum Brands
Australia Pty Ltd and in New Zealand against Spectrum Brands New Zealand Limited.
Contact us or the Supplier for further details.
Spectrum Brands Australia Pty Ltd
Chifley Business Park
1 Chifley Drive
Mentone, VIC 3194 Australia
Customer service in Australia: 1800 623 118
Website: www.remington-products.com.au
Spectrum Brands New Zealand Limited
Building C, Ground Floor
600 Great South Road,
Greenlane, Auckland 1051 New Zealand
Customer service in New Zealand: 0800 736 776
Website: www.remington-products.com.au
REMINGTON SERVICE HOTLINE
Australia 1800 623 118 (toll free)
New Zealand 0800 736 776 (toll free)
AUTHORISED REPAIR CENTRES
Visit www.remington-products.com.au for Authorised repair centre details.
® Registered Trademark of Spectrum Brands, Inc. (SBI), or one of its subsidiaries
Manufactured to Spectrum Brands specifications in the PRC
© 2012 SBI
Rev.05/12
Part No. T22-0000311
USE & CARE
MANUAL
PLEASE READ
PRIOR TO USE
TOOLS OF THE TRADE
FOIL SHAVER
This product is not suitable to use in a bath or shower.
The shaver conforms to radio frequency
interference requirements.
Anyproductpurchasedandusedcommercially
carries a limited 90 Day Warranty.
10
9
F3700AU_IFU_FA_170712.indd 1-7 17/07/12 11:42 AM
3. Gently tap the shaver head on a flat surface to remove any
loose hair particles, and rinse the shaver head under warm
water (Diagram J). Never submerge your
shaver under water.
4. Thoroughly clean the cutter and trimmer
with a brush (Diagram J).
5. Never use the cleaning brush on the foils,
as damage may occur.
6. Shake off any excess water.
7. Leave the shave unit open to allow the
shaver to
dry completely.
8. Lubricate the shaver with a spray of
Remington® Shaver Saver (SP4) on the
foil and cutters.
9. Replace the head assembly, simply by
pushing it on the shaver.
Cover shaver head with the protective head guard between
uses. When removing the head guard or placing it back onto
the shaver, do not apply pressure to the floating cutter
surfaces, as you may damage them.
Lubricate
Remington® Shaver Saver (SP-4) lubricates, cleans and
protects your shaver’s foil and cutter assembly. The lubricant
helps remove hair clippings while reducing wear. Spray on the
foil and cutters after each shave to keep your shaver operating
at peak performance.
Cleaning Cautions
•Never submerge the shaver completely into water.
•Never clean the shaver or replace the cutters while it is
plugged into an electrical outlet.
•Do not use any aggressive cleaning agents, as this may
damage the shaver.
Replacing Your Heads & Cutters
It is very important to replace your foils and cutters when
necessary to ensure a close, comfortable shave without
I
J
irritation. We recommend they be replaced every 6 months for
optimal performance. Here are some signs of head and cutter
wear, indicating that replacement is needed.
Signs that your foils and cutters need replacing:
• Irritation:Asfoilsgetworn,youmayexperienceskinirritation.
Asthefoilsbecomeexcessivelywornyoumayexperience
some skin irritation or redness.
• Pulling:Asthecutterswear,yourshavemaynotfeelasclose
and you may feel your cutter pulling your hair.
• Wearthrough:Youmaynoticethatthecuttershaveworn
through the foils.
TO REPLACE THE FOIL
• Pullthefoilassemblyuptoremovefromthehairpocket.
• Insertnewfoilassemblyinhairpocketuntilitsnapsinplace.
TO REPLACE THE CUTTERS
• Graspcutterbetweenthumbandforefingerandpullupward.
• Snapbothnewcutterassembliesintotopofoscillatortips.
STORAGE
When not in use, always unplug the power adaptor from the
power outlet. Never wrap the cord of the power adaptor
around the unit as this will cause the cord to wear prematurely
and break. Handle the cord carefully for long life and avoid
jerking, twisting or straining especially at the power plug. If the
cord becomes twisted in use, periodically straighten it.
2 YEAR WARRANTY F3700AU
MONEY BACK OFFER - Australia/New Zealand Only
If within 30 days you are not fully satisfied with your
Remington® shaver, just return the shaver with this completed
couponandacopyofyourAustralian/NewZealandpurchase
receipt to Remington®. In return, we will send you a cheque for
the full purchase price of the shaver. Please allow 6-8 weeks
for your cheque to arrive.
Name:
Address:
City:
State: Postcode:
12
11
13 14
Spectrum Brands Australia Pty Ltd and Spectrum Brands New Zealand Limited
WARRANTY AGAINST DEFECTS
In this warranty:
Australian Consumer Law means the Australian consumer law set out in Schedule 2
to the Competition and Consumer Act 2010;
CGA means the New Zealand Consumer Guarantees Act 1993;
Goods means the product or equipment which was accompanied by this warranty and
purchased in Australia or New Zealand, as the case may be;
Manufacturer, We or us means:
1. for Goods purchased in Australia, Spectrum Brands Australia Pty Ltd
ACN, 007 070 573; or
2. for Goods purchased in New Zealand, Spectrum Brands New Zealand Limited,
as the case may be, contact details as set out at the end of this warranty;
Supplier means the authorised distributor or retailer of the Goods that sold you the Goods
in Australia or in New Zealand; and
You means you, the original end-user purchaser of the Goods.
1. Our goods come with guarantees that cannot be excluded under the Australian
Consumer Law, or the CGA. You are entitled to a replacement or refund for a major failure
and compensation for any other reasonably foreseeable loss or damage. You are also
entitled to have the goods repaired or replaced if the goods fail to be of acceptable
quality and the failure does not amount to a major failure.
2. The benefits provided by this Warranty are in addition to all other rights and remedies in
respect of the Goods which the consumer has under either the Australian Consumer Law
or the CGA. The original purchaser of the Goods is provided with the following Warranty
subject to the Warranty Conditions:
3. We warrant the Goods for all parts defective in workmanship or materials for the period
of two (2) years from the date of purchase (Warranty Period). If the Goods prove
defective within the Warranty Period by reason of improper workmanship or material,
we may, at our own discretion, repair or replace the Goods without charge.
Warranty Conditions
4. The Goods must be used in accordance with the manufacturer’s instructions. This
Warranty does not apply should the defect in or failure of the Goods be attributable to
misuse, abuse, accident or non-observance of manufacturer’s instructions on the part of
the user. As far as the law permits, the manufacturer does not accept liability for any
direct or consequential loss, damage or other expense caused by or arising out of any
failure to use the Goods in accordance with the manufacturer’s instructions.
5. Exhaustible components (such as shaver heads, cutters and foils) of the Goods
are included under this Warranty only where there is a defect in workmanship or
materials used.
6. The warranty granted under clause 3 is limited to repair or replacement only.
7. Any parts of the Goods replaced during repairs or any product replaced remain the
property of the manufacturer. In the event of the Goods being replaced during the
Warranty Period, the warranty on the replacement Goods will expire on the same date
as for the Warranty Period on the original Goods which are replaced.
8. In order to claim under the warranty granted under clause 3 you must:
(a) Retain this warranty with your receipt/proof of purchase; and
(b) Return the Goods to us at the relevant address below or to the Supplier by prepaid
freight within the Warranty Period accompanied with (i) the legible and unmodified
original proof of purchase, which clearly indicates the name and address of the
Supplier, the date and place of purchase, the product name or other product serial
number and (ii) this warranty.
9. This warranty is immediately void if:
(a) Any serial number or appliance plate is removed or defaced;
(b) The Goods have been serviced or otherwise repaired by a person not authorised to
do so by us or where non approved replaced parts are used.
10. The Goods are designed for domestic use only. A limited 90-day Warranty applies to any
industrial or commercial use of the Goods. The Goods must be connected to the electrical
voltage requirements as specified in the ratings label located on the Goods.
11. This warranty does not cover the cost of claiming under the warranty or transport of the
Goods to and from the Supplier or us.
12. This warranty is only valid and enforceable in Australia against Spectrum Brands
Australia Pty Ltd and in New Zealand against Spectrum Brands New Zealand Limited.
Contact us or the Supplier for further details.
Spectrum Brands Australia Pty Ltd
Chifley Business Park
1 Chifley Drive
Mentone, VIC 3194 Australia
Customer service in Australia: 1800 623 118
Website: www.remington-products.com.au
Spectrum Brands New Zealand Limited
Building C, Ground Floor
600 Great South Road,
Greenlane, Auckland 1051 New Zealand
Customer service in New Zealand: 0800 736 776
Website: www.remington-products.com.au
REMINGTON SERVICE HOTLINE
Australia 1800 623 118 (toll free)
New Zealand 0800 736 776 (toll free)
AUTHORISED REPAIR CENTRES
Visit www.remington-products.com.au for Authorised repair centre details.
® Registered Trademark of Spectrum Brands, Inc. (SBI), or one of its subsidiaries
Manufactured to Spectrum Brands specifications in the PRC
© 2012 SBI
Rev.05/12
Part No. T22-0000311
USE & CARE
MANUAL
PLEASE READ
PRIOR TO USE
TOOLS OF THE TRADE
FOIL SHAVER
This product is not suitable to use in a bath or shower.
The shaver conforms to radio frequency
interference requirements.
Anyproductpurchasedandusedcommercially
carries a limited 90 Day Warranty.
109
F3700AU_IFU_FA_170712.indd 1-7 17/07/12 11:42 AM
3. Gently tap the shaver head on a flat surface to remove any
loose hair particles, and rinse the shaver head under warm
water (Diagram J). Never submerge your
shaver under water.
4. Thoroughly clean the cutter and trimmer
with a brush (Diagram J).
5. Never use the cleaning brush on the foils,
as damage may occur.
6. Shake off any excess water.
7. Leave the shave unit open to allow the
shaver to
dry completely.
8. Lubricate the shaver with a spray of
Remington® Shaver Saver (SP4) on the
foil and cutters.
9. Replace the head assembly, simply by
pushing it on the shaver.
Cover shaver head with the protective head guard between
uses. When removing the head guard or placing it back onto
the shaver, do not apply pressure to the floating cutter
surfaces, as you may damage them.
Lubricate
Remington® Shaver Saver (SP-4) lubricates, cleans and
protects your shaver’s foil and cutter assembly. The lubricant
helps remove hair clippings while reducing wear. Spray on the
foil and cutters after each shave to keep your shaver operating
at peak performance.
Cleaning Cautions
•Never submerge the shaver completely into water.
•Never clean the shaver or replace the cutters while it is
plugged into an electrical outlet.
•Do not use any aggressive cleaning agents, as this may
damage the shaver.
Replacing Your Heads & Cutters
It is very important to replace your foils and cutters when
necessary to ensure a close, comfortable shave without
I
J
irritation. We recommend they be replaced every 6 months for
optimal performance. Here are some signs of head and cutter
wear, indicating that replacement is needed.
Signs that your foils and cutters need replacing:
• Irritation:Asfoilsgetworn,youmayexperienceskinirritation.
Asthefoilsbecomeexcessivelywornyoumayexperience
some skin irritation or redness.
• Pulling:Asthecutterswear,yourshavemaynotfeelasclose
and you may feel your cutter pulling your hair.
• Wearthrough:Youmaynoticethatthecuttershaveworn
through the foils.
TO REPLACE THE FOIL
• Pullthefoilassemblyuptoremovefromthehairpocket.
• Insertnewfoilassemblyinhairpocketuntilitsnapsinplace.
TO REPLACE THE CUTTERS
• Graspcutterbetweenthumbandforefingerandpullupward.
• Snapbothnewcutterassembliesintotopofoscillatortips.
STORAGE
When not in use, always unplug the power adaptor from the
power outlet. Never wrap the cord of the power adaptor
around the unit as this will cause the cord to wear prematurely
and break. Handle the cord carefully for long life and avoid
jerking, twisting or straining especially at the power plug. If the
cord becomes twisted in use, periodically straighten it.
2 YEAR WARRANTY F3700AU
MONEY BACK OFFER - Australia/New Zealand Only
If within 30 days you are not fully satisfied with your
Remington® shaver, just return the shaver with this completed
couponandacopyofyourAustralian/NewZealandpurchase
receipt to Remington®. In return, we will send you a cheque for
the full purchase price of the shaver. Please allow 6-8 weeks
for your cheque to arrive.
Name:
Address:
City:
State: Postcode:
12
11 13 14
Spectrum Brands Australia Pty Ltd and Spectrum Brands New Zealand Limited
WARRANTY AGAINST DEFECTS
In this warranty:
Australian Consumer Law means the Australian consumer law set out in Schedule 2
to the Competition and Consumer Act 2010;
CGA means the New Zealand Consumer Guarantees Act 1993;
Goods means the product or equipment which was accompanied by this warranty and
purchased in Australia or New Zealand, as the case may be;
Manufacturer, We or us means:
1. for Goods purchased in Australia, Spectrum Brands Australia Pty Ltd
ACN, 007 070 573; or
2. for Goods purchased in New Zealand, Spectrum Brands New Zealand Limited,
as the case may be, contact details as set out at the end of this warranty;
Supplier means the authorised distributor or retailer of the Goods that sold you the Goods
in Australia or in New Zealand; and
You means you, the original end-user purchaser of the Goods.
1. Our goods come with guarantees that cannot be excluded under the Australian
Consumer Law, or the CGA. You are entitled to a replacement or refund for a major failure
and compensation for any other reasonably foreseeable loss or damage. You are also
entitled to have the goods repaired or replaced if the goods fail to be of acceptable
quality and the failure does not amount to a major failure.
2. The benefits provided by this Warranty are in addition to all other rights and remedies in
respect of the Goods which the consumer has under either the Australian Consumer Law
or the CGA. The original purchaser of the Goods is provided with the following Warranty
subject to the Warranty Conditions:
3. We warrant the Goods for all parts defective in workmanship or materials for the period
of two (2) years from the date of purchase (Warranty Period). If the Goods prove
defective within the Warranty Period by reason of improper workmanship or material,
we may, at our own discretion, repair or replace the Goods without charge.
Warranty Conditions
4. The Goods must be used in accordance with the manufacturer’s instructions. This
Warranty does not apply should the defect in or failure of the Goods be attributable to
misuse, abuse, accident or non-observance of manufacturer’s instructions on the part of
the user. As far as the law permits, the manufacturer does not accept liability for any
direct or consequential loss, damage or other expense caused by or arising out of any
failure to use the Goods in accordance with the manufacturer’s instructions.
5. Exhaustible components (such as shaver heads, cutters and foils) of the Goods
are included under this Warranty only where there is a defect in workmanship or
materials used.
6. The warranty granted under clause 3 is limited to repair or replacement only.
7. Any parts of the Goods replaced during repairs or any product replaced remain the
property of the manufacturer. In the event of the Goods being replaced during the
Warranty Period, the warranty on the replacement Goods will expire on the same date
as for the Warranty Period on the original Goods which are replaced.
8. In order to claim under the warranty granted under clause 3 you must:
(a) Retain this warranty with your receipt/proof of purchase; and
(b) Return the Goods to us at the relevant address below or to the Supplier by prepaid
freight within the Warranty Period accompanied with (i) the legible and unmodified
original proof of purchase, which clearly indicates the name and address of the
Supplier, the date and place of purchase, the product name or other product serial
number and (ii) this warranty.
9. This warranty is immediately void if:
(a) Any serial number or appliance plate is removed or defaced;
(b) The Goods have been serviced or otherwise repaired by a person not authorised to
do so by us or where non approved replaced parts are used.
10. The Goods are designed for domestic use only. A limited 90-day Warranty applies to any
industrial or commercial use of the Goods. The Goods must be connected to the electrical
voltage requirements as specified in the ratings label located on the Goods.
11. This warranty does not cover the cost of claiming under the warranty or transport of the
Goods to and from the Supplier or us.
12. This warranty is only valid and enforceable in Australia against Spectrum Brands
Australia Pty Ltd and in New Zealand against Spectrum Brands New Zealand Limited.
Contact us or the Supplier for further details.
Spectrum Brands Australia Pty Ltd
Chifley Business Park
1 Chifley Drive
Mentone, VIC 3194 Australia
Customer service in Australia: 1800 623 118
Website: www.remington-products.com.au
Spectrum Brands New Zealand Limited
Building C, Ground Floor
600 Great South Road,
Greenlane, Auckland 1051 New Zealand
Customer service in New Zealand: 0800 736 776
Website: www.remington-products.com.au
REMINGTON SERVICE HOTLINE
Australia 1800 623 118 (toll free)
New Zealand 0800 736 776 (toll free)
AUTHORISED REPAIR CENTRES
Visit www.remington-products.com.au for Authorised repair centre details.
® Registered Trademark of Spectrum Brands, Inc. (SBI), or one of its subsidiaries
Manufactured to Spectrum Brands specifications in the PRC
© 2012 SBI
Rev.05/12
Part No. T22-0000311
USE & CARE
MANUAL
PLEASE READ
PRIOR TO USE
TOOLS OF THE TRADE
FOIL SHAVER
This product is not suitable to use in a bath or shower.
The shaver conforms to radio frequency
interference requirements.
Anyproductpurchasedandusedcommercially
carries a limited 90 Day Warranty.
109
F3700AU_IFU_FA_170712.indd 1-7 17/07/12 11:42 AM
3. Gently tap the shaver head on a flat surface to remove any
loose hair particles, and rinse the shaver head under warm
water (Diagram J). Never submerge your
shaver under water.
4. Thoroughly clean the cutter and trimmer
with a brush (Diagram J).
5. Never use the cleaning brush on the foils,
as damage may occur.
6. Shake off any excess water.
7. Leave the shave unit open to allow the
shaver to
dry completely.
8. Lubricate the shaver with a spray of
Remington® Shaver Saver (SP4) on the
foil and cutters.
9. Replace the head assembly, simply by
pushing it on the shaver.
Cover shaver head with the protective head guard between
uses. When removing the head guard or placing it back onto
the shaver, do not apply pressure to the floating cutter
surfaces, as you may damage them.
Lubricate
Remington® Shaver Saver (SP-4) lubricates, cleans and
protects your shaver’s foil and cutter assembly. The lubricant
helps remove hair clippings while reducing wear. Spray on the
foil and cutters after each shave to keep your shaver operating
at peak performance.
Cleaning Cautions
•Never submerge the shaver completely into water.
•Never clean the shaver or replace the cutters while it is
plugged into an electrical outlet.
•Do not use any aggressive cleaning agents, as this may
damage the shaver.
Replacing Your Heads & Cutters
It is very important to replace your foils and cutters when
necessary to ensure a close, comfortable shave without
I
J
irritation. We recommend they be replaced every 6 months for
optimal performance. Here are some signs of head and cutter
wear, indicating that replacement is needed.
Signs that your foils and cutters need replacing:
• Irritation:Asfoilsgetworn,youmayexperienceskinirritation.
Asthefoilsbecomeexcessivelywornyoumayexperience
some skin irritation or redness.
• Pulling:Asthecutterswear,yourshavemaynotfeelasclose
and you may feel your cutter pulling your hair.
• Wearthrough:Youmaynoticethatthecuttershaveworn
through the foils.
TO REPLACE THE FOIL
• Pullthefoilassemblyuptoremovefromthehairpocket.
• Insertnewfoilassemblyinhairpocketuntilitsnapsinplace.
TO REPLACE THE CUTTERS
• Graspcutterbetweenthumbandforefingerandpullupward.
• Snapbothnewcutterassembliesintotopofoscillatortips.
STORAGE
When not in use, always unplug the power adaptor from the
power outlet. Never wrap the cord of the power adaptor
around the unit as this will cause the cord to wear prematurely
and break. Handle the cord carefully for long life and avoid
jerking, twisting or straining especially at the power plug. If the
cord becomes twisted in use, periodically straighten it.
2 YEAR WARRANTY F3700AU
MONEY BACK OFFER - Australia/New Zealand Only
If within 30 days you are not fully satisfied with your
Remington® shaver, just return the shaver with this completed
couponandacopyofyourAustralian/NewZealandpurchase
receipt to Remington®. In return, we will send you a cheque for
the full purchase price of the shaver. Please allow 6-8 weeks
for your cheque to arrive.
Name:
Address:
City:
State: Postcode:
1211
13
14
Spectrum Brands Australia Pty Ltd and Spectrum Brands New Zealand Limited
WARRANTY AGAINST DEFECTS
In this warranty:
Australian Consumer Law means the Australian consumer law set out in Schedule 2
to the Competition and Consumer Act 2010;
CGA means the New Zealand Consumer Guarantees Act 1993;
Goods means the product or equipment which was accompanied by this warranty and
purchased in Australia or New Zealand, as the case may be;
Manufacturer, We or us means:
1. for Goods purchased in Australia, Spectrum Brands Australia Pty Ltd
ACN, 007 070 573; or
2. for Goods purchased in New Zealand, Spectrum Brands New Zealand Limited,
as the case may be, contact details as set out at the end of this warranty;
Supplier means the authorised distributor or retailer of the Goods that sold you the Goods
in Australia or in New Zealand; and
You means you, the original end-user purchaser of the Goods.
1. Our goods come with guarantees that cannot be excluded under the Australian
Consumer Law, or the CGA. You are entitled to a replacement or refund for a major failure
and compensation for any other reasonably foreseeable loss or damage. You are also
entitled to have the goods repaired or replaced if the goods fail to be of acceptable
quality and the failure does not amount to a major failure.
2. The benefits provided by this Warranty are in addition to all other rights and remedies in
respect of the Goods which the consumer has under either the Australian Consumer Law
or the CGA. The original purchaser of the Goods is provided with the following Warranty
subject to the Warranty Conditions:
3. We warrant the Goods for all parts defective in workmanship or materials for the period
of two (2) years from the date of purchase (Warranty Period). If the Goods prove
defective within the Warranty Period by reason of improper workmanship or material,
we may, at our own discretion, repair or replace the Goods without charge.
Warranty Conditions
4. The Goods must be used in accordance with the manufacturer’s instructions. This
Warranty does not apply should the defect in or failure of the Goods be attributable to
misuse, abuse, accident or non-observance of manufacturer’s instructions on the part of
the user. As far as the law permits, the manufacturer does not accept liability for any
direct or consequential loss, damage or other expense caused by or arising out of any
failure to use the Goods in accordance with the manufacturer’s instructions.
5. Exhaustible components (such as shaver heads, cutters and foils) of the Goods
are included under this Warranty only where there is a defect in workmanship or
materials used.
6. The warranty granted under clause 3 is limited to repair or replacement only.
7. Any parts of the Goods replaced during repairs or any product replaced remain the
property of the manufacturer. In the event of the Goods being replaced during the
Warranty Period, the warranty on the replacement Goods will expire on the same date
as for the Warranty Period on the original Goods which are replaced.
8. In order to claim under the warranty granted under clause 3 you must:
(a) Retain this warranty with your receipt/proof of purchase; and
(b) Return the Goods to us at the relevant address below or to the Supplier by prepaid
freight within the Warranty Period accompanied with (i) the legible and unmodified
original proof of purchase, which clearly indicates the name and address of the
Supplier, the date and place of purchase, the product name or other product serial
number and (ii) this warranty.
9. This warranty is immediately void if:
(a) Any serial number or appliance plate is removed or defaced;
(b) The Goods have been serviced or otherwise repaired by a person not authorised to
do so by us or where non approved replaced parts are used.
10. The Goods are designed for domestic use only. A limited 90-day Warranty applies to any
industrial or commercial use of the Goods. The Goods must be connected to the electrical
voltage requirements as specified in the ratings label located on the Goods.
11. This warranty does not cover the cost of claiming under the warranty or transport of the
Goods to and from the Supplier or us.
12. This warranty is only valid and enforceable in Australia against Spectrum Brands
Australia Pty Ltd and in New Zealand against Spectrum Brands New Zealand Limited.
Contact us or the Supplier for further details.
Spectrum Brands Australia Pty Ltd
Chifley Business Park
1 Chifley Drive
Mentone, VIC 3194 Australia
Customer service in Australia: 1800 623 118
Website: www.remington-products.com.au
Spectrum Brands New Zealand Limited
Building C, Ground Floor
600 Great South Road,
Greenlane, Auckland 1051 New Zealand
Customer service in New Zealand: 0800 736 776
Website: www.remington-products.com.au
REMINGTON SERVICE HOTLINE
Australia 1800 623 118 (toll free)
New Zealand 0800 736 776 (toll free)
AUTHORISED REPAIR CENTRES
Visit www.remington-products.com.au for Authorised repair centre details.
® Registered Trademark of Spectrum Brands, Inc. (SBI), or one of its subsidiaries
Manufactured to Spectrum Brands specifications in the PRC
© 2012 SBI
Rev.05/12
Part No. T22-0000311
USE & CARE
MANUAL
PLEASE READ
PRIOR TO USE
TOOLS OF THE TRADE
FOIL SHAVER
This product is not suitable to use in a bath or shower.
The shaver conforms to radio frequency
interference requirements.
Anyproductpurchasedandusedcommercially
carries a limited 90 Day Warranty.
109
F3700AU_IFU_FA_170712.indd 1-7 17/07/12 11:42 AM
3. Gently tap the shaver head on a flat surface to remove any
loose hair particles, and rinse the shaver head under warm
water (Diagram J). Never submerge your
shaver under water.
4. Thoroughly clean the cutter and trimmer
with a brush (Diagram J).
5. Never use the cleaning brush on the foils,
as damage may occur.
6. Shake off any excess water.
7. Leave the shave unit open to allow the
shaver to
dry completely.
8. Lubricate the shaver with a spray of
Remington® Shaver Saver (SP4) on the
foil and cutters.
9. Replace the head assembly, simply by
pushing it on the shaver.
Cover shaver head with the protective head guard between
uses. When removing the head guard or placing it back onto
the shaver, do not apply pressure to the floating cutter
surfaces, as you may damage them.
Lubricate
Remington® Shaver Saver (SP-4) lubricates, cleans and
protects your shaver’s foil and cutter assembly. The lubricant
helps remove hair clippings while reducing wear. Spray on the
foil and cutters after each shave to keep your shaver operating
at peak performance.
Cleaning Cautions
•Never submerge the shaver completely into water.
•Never clean the shaver or replace the cutters while it is
plugged into an electrical outlet.
•Do not use any aggressive cleaning agents, as this may
damage the shaver.
Replacing Your Heads & Cutters
It is very important to replace your foils and cutters when
necessary to ensure a close, comfortable shave without
I
J
irritation. We recommend they be replaced every 6 months for
optimal performance. Here are some signs of head and cutter
wear, indicating that replacement is needed.
Signs that your foils and cutters need replacing:
• Irritation:Asfoilsgetworn,youmayexperienceskinirritation.
Asthefoilsbecomeexcessivelywornyoumayexperience
some skin irritation or redness.
• Pulling:Asthecutterswear,yourshavemaynotfeelasclose
and you may feel your cutter pulling your hair.
• Wearthrough:Youmaynoticethatthecuttershaveworn
through the foils.
TO REPLACE THE FOIL
• Pullthefoilassemblyuptoremovefromthehairpocket.
• Insertnewfoilassemblyinhairpocketuntilitsnapsinplace.
TO REPLACE THE CUTTERS
• Graspcutterbetweenthumbandforefingerandpullupward.
• Snapbothnewcutterassembliesintotopofoscillatortips.
STORAGE
When not in use, always unplug the power adaptor from the
power outlet. Never wrap the cord of the power adaptor
around the unit as this will cause the cord to wear prematurely
and break. Handle the cord carefully for long life and avoid
jerking, twisting or straining especially at the power plug. If the
cord becomes twisted in use, periodically straighten it.
2 YEAR WARRANTY F3700AU
MONEY BACK OFFER - Australia/New Zealand Only
If within 30 days you are not fully satisfied with your
Remington® shaver, just return the shaver with this completed
couponandacopyofyourAustralian/NewZealandpurchase
receipt to Remington®. In return, we will send you a cheque for
the full purchase price of the shaver. Please allow 6-8 weeks
for your cheque to arrive.
Name:
Address:
City:
State: Postcode:
1211 13
14
Spectrum Brands Australia Pty Ltd and Spectrum Brands New Zealand Limited
WARRANTY AGAINST DEFECTS
In this warranty:
Australian Consumer Law means the Australian consumer law set out in Schedule 2
to the Competition and Consumer Act 2010;
CGA means the New Zealand Consumer Guarantees Act 1993;
Goods means the product or equipment which was accompanied by this warranty and
purchased in Australia or New Zealand, as the case may be;
Manufacturer, We or us means:
1. for Goods purchased in Australia, Spectrum Brands Australia Pty Ltd
ACN, 007 070 573; or
2. for Goods purchased in New Zealand, Spectrum Brands New Zealand Limited,
as the case may be, contact details as set out at the end of this warranty;
Supplier means the authorised distributor or retailer of the Goods that sold you the Goods
in Australia or in New Zealand; and
You means you, the original end-user purchaser of the Goods.
1. Our goods come with guarantees that cannot be excluded under the Australian
Consumer Law, or the CGA. You are entitled to a replacement or refund for a major failure
and compensation for any other reasonably foreseeable loss or damage. You are also
entitled to have the goods repaired or replaced if the goods fail to be of acceptable
quality and the failure does not amount to a major failure.
2. The benefits provided by this Warranty are in addition to all other rights and remedies in
respect of the Goods which the consumer has under either the Australian Consumer Law
or the CGA. The original purchaser of the Goods is provided with the following Warranty
subject to the Warranty Conditions:
3. We warrant the Goods for all parts defective in workmanship or materials for the period
of two (2) years from the date of purchase (Warranty Period). If the Goods prove
defective within the Warranty Period by reason of improper workmanship or material,
we may, at our own discretion, repair or replace the Goods without charge.
Warranty Conditions
4. The Goods must be used in accordance with the manufacturer’s instructions. This
Warranty does not apply should the defect in or failure of the Goods be attributable to
misuse, abuse, accident or non-observance of manufacturer’s instructions on the part of
the user. As far as the law permits, the manufacturer does not accept liability for any
direct or consequential loss, damage or other expense caused by or arising out of any
failure to use the Goods in accordance with the manufacturer’s instructions.
5. Exhaustible components (such as shaver heads, cutters and foils) of the Goods
are included under this Warranty only where there is a defect in workmanship or
materials used.
6. The warranty granted under clause 3 is limited to repair or replacement only.
7. Any parts of the Goods replaced during repairs or any product replaced remain the
property of the manufacturer. In the event of the Goods being replaced during the
Warranty Period, the warranty on the replacement Goods will expire on the same date
as for the Warranty Period on the original Goods which are replaced.
8. In order to claim under the warranty granted under clause 3 you must:
(a) Retain this warranty with your receipt/proof of purchase; and
(b) Return the Goods to us at the relevant address below or to the Supplier by prepaid
freight within the Warranty Period accompanied with (i) the legible and unmodified
original proof of purchase, which clearly indicates the name and address of the
Supplier, the date and place of purchase, the product name or other product serial
number and (ii) this warranty.
9. This warranty is immediately void if:
(a) Any serial number or appliance plate is removed or defaced;
(b) The Goods have been serviced or otherwise repaired by a person not authorised to
do so by us or where non approved replaced parts are used.
10. The Goods are designed for domestic use only. A limited 90-day Warranty applies to any
industrial or commercial use of the Goods. The Goods must be connected to the electrical
voltage requirements as specified in the ratings label located on the Goods.
11. This warranty does not cover the cost of claiming under the warranty or transport of the
Goods to and from the Supplier or us.
12. This warranty is only valid and enforceable in Australia against Spectrum Brands
Australia Pty Ltd and in New Zealand against Spectrum Brands New Zealand Limited.
Contact us or the Supplier for further details.
Spectrum Brands Australia Pty Ltd
Chifley Business Park
1 Chifley Drive
Mentone, VIC 3194 Australia
Customer service in Australia: 1800 623 118
Website: www.remington-products.com.au
Spectrum Brands New Zealand Limited
Building C, Ground Floor
600 Great South Road,
Greenlane, Auckland 1051 New Zealand
Customer service in New Zealand: 0800 736 776
E-mail: [email protected]
Website: www.remington-products.com.au
REMINGTON SERVICE HOTLINE
Australia 1800 623 118 (toll free)
New Zealand 0800 736 776 (toll free)
AUTHORISED REPAIR CENTRES
Visit www.remington-products.com.au for Authorised repair centre details.
® Registered Trademark of Spectrum Brands, Inc. (SBI), or one of its subsidiaries
Manufactured to Spectrum Brands specifications in the PRC
© 2012 SBI
Rev.05/12
Part No. T22-0000311
USE & CARE
MANUAL
PLEASE READ
PRIOR TO USE
TOOLS OF THE TRADE
FOIL SHAVER
This product is not suitable to use in a bath or shower.
The shaver conforms to radio frequency
interference requirements.
Anyproductpurchasedandusedcommercially
carries a limited 90 Day Warranty.
109
F3700AU_IFU_FA_170712.indd 1-7 17/07/12 11:42 AM
Table of contents
Other Remington Electric Shaver manuals
Remington
Remington Durablade Pro MB070 User manual
Remington
Remington Precision Trimming HC-810 User manual
Remington
Remington PR1855 User manual
Remington
Remington MB4120 User manual
Remington
Remington MB4130 User manual
Remington
Remington MB4040 User manual
Remington
Remington BHT6256 User manual
Remington
Remington FR500 User manual
Remington
Remington MB4010 User manual
Remington
Remington R27A User manual
Remington
Remington B4 Style Series User manual
Remington
Remington MPT-3400 User manual
Remington
Remington DURABLADE MB050 User manual
Remington
Remington TITANUIM MICROFLEX R-846 User manual
Remington
Remington Barber's Best Pro MB4373AU User manual
Remington
Remington MB6850AU User manual
Remington
Remington Style Series User manual
Remington
Remington XF8550AU User manual
Remington
Remington FF-400 User manual
Remington
Remington PG-520 User manual
