Remta RR01 User manual

ROLLER HOT DOG COOKER
Producer: REMTA MAKİNA İTH. İHR. SAN. TİC. LTD. ŞTİ.
Producing Address: Akçaburgaz Mah. 4. Cad. 153. Sok. No:23 34522 Esenyurt - İstanbul
[phone] • [email protected] • www.remta.com.tr
MODELS: RR01
USER MANUEL

1. You will need this manual for the safety warnings
and precautions, operating, inspection, mainte-
nance and cleaning procedures. Keep your
invoice with this manual. Write the invoice number
on the inside of the front cover. Keep this manual
and invoice in a safe and dry place for future
reference.
2. The warnings, cautions and instructions dis-
cussed in this instruction manual cannot cover all
possible conditions and situations that may occur.
It must be understood by the operator that
common sense and caution are factors which
cannot be built into this product, but must be
supplied by the operator.
3. NEVER use this product for anything other than
its intended use. NEVER modify this product.
Failure to comply with the precautions, warnings
and recommendations in this manual will nullify
your warranty and may result in injury or even
death.
4.ALWAYS ensure that this hot dog roller is
plugged into a grounded outlet with the proper
power supply available.
5. DO NOT unplug the machine by pulling or
tugging on the power cord. Firmly grasp the plug
and remove from outlet.
6. MAKE SURE that the power outlet, plug and
power cords used are in good condition. Worn,
frayed or damaged plugs, cords and outlets
should be replaced or repaired by a certied
electrician who is properly qualied to meet local
safety and electrical codes. Power supply cords
should be replaced by the manufacturer.
AVOID using extension cords or 3-prong
adaptors.
7. To reduce the risk of electrical shock or re,
MAKE SURE that your unit is properly grounded.
NEVER TAMPER WITH, REMOVE OR CUT THE
GROUNDING PIN!! The wall outlet used with this
roller MUST be properly grounded. If you do not
have a grounded outlet, have one installed by a
certied electrician who is properly qualied to
meet local safety and electrical codes.
8.Make sure your machine is unplugged when you
conduct any maintenance or repair. A qualied
service technician should always perform service
or repair.
9. This product is certied for household or
commercial use.
10.Do not cover the power cord. DO NOT immerse
cord in water or use in high trafc areas. DO NOT
run cord over carpets or heating sources or
elements. NEVER use with damaged cords or
plugs.
GENERAL SAFETY PRECAUTIONS
11.INTENDED FOR UPRIGHT, FREESTANDING
USE ONLY. Do not install in cabinet or enclosed
spaces.
12.DO NOT operate with missing or broken parts.
13.This product is intended for INDOOR USE ONLY.
DO NOT USE OUTDOORS.
14.Only qualied repair personnel should perform
griller service. Service or maintenance
performed by unqualied personnel could result
in injury.
15.Do not operate this roller in explosive
atmospheres, such as in the presence of
ammable liquids, gases, or dust.
16.DO NOT tamper with or modify the controls.
17.KEEP UPRIGHT when transporting. DO NOT
UPEND OR TURN UPSIDE DOWN.
SPECIFICATIONS
Model Rollers Temp Power Voltage Dimensions
STORAGE & TRANSPORTATION
NEVER STORE UPSIDE DOWN.
When storing any hot dog roller, rst be sure to
DISCONNECT FROM POWER SUPPLY.
Store away from moisture and ammable materials,
fumes and chemicals.
Cover when stored for long periods to prevent dust
buildup.
When transporting the roller/grill, AVOID EXCESSIVE
VIBRATION.
KEEP UPRIGHT when transporting. DO NOT UPEND OR
TURN UPSIDE DOWN.
RR01 7 250 1500 W 220 V 600x400
x180mm

OPERATION & MAINTENANCE
HOW TO USE YOUR HOT DOG COOKER/GRILLER
IMPORTANT!
Before using your hot dog cooker for the rst time, apply a vegetable oil such as sunower oil or
canola oil to the ends of your rollers. This will help to keep them turning smoothly and easily.
Avoid using non-stick sprays because these can contain lecithin, which will cause an eventual
buildup on your rollers.
To use your machine:
1. Turn the Power switch to ON.
2. Use the temperature control dials to the desired settings. To cook product more rapidly, turn the
temperature dials to their highest settings, or in a clockwise direction. To cook more slowly, or to
hold already cooked product on a warm setting, adjust the temperature dial down, or in a counter-
clockwise direction.
Note: Your DAWG series cooker’s separate temperature dials control the heat settings for different
sets of rollers. The Front dial controls all rollers (number of rollers will vary with model), while the
Back dial controls the last 3 rollers of your cooker. This allows you to cook some hot dogs more
quickly, while holding more cooked product at a lower warming temperature. Model 4095 has a
dial control which affects all 5 rollers.
In addition, the green heating indicator lights marked “Heating” will be lit when the rollers are
actively being heated; when they have reached the temperature set by the temperature dials, the
light will go out. Increasing the temperature setting for a group of rollers will cause the indicator
light to go on and when the new temperature is reached the light will extinguish to let you know
that the new setting is reached.
CAUTION! Rollers will be hot. Use care when cleaning, adding product or serving product!
CLEANING AND MAINTENANCE
IMPORTANT!
Do not immerse any part of this machine in water. Turn the machine OFF prior to cleaning or
maintenance and allow to cool before touching rollers. CAUTION! Rollers will be hot.
Follow the cleaning and maintenance guidelines to ensure a long life for your machine.
To clean your machine:
1. Turn the Power switch to OFF.
2. Use a soft cloth or towel to wipe the surfaces of the rollers. DO NOT USE METAL TO CLEAN
YOUR ROLLERS! This may result in damage to the machine. In most cases the natural oils
exuded from sausages or hot dogs will keep the machine well lubricated. You should simply need
to wipe the rollers and outside surfaces of your machine with a cloth to remove excess oils or
dust. Should you need to remove any caked on material such as cheese or condiments, use a
wooden utensil and then clean with a soft cloth.

HOT DOG ROLLER WIRING DIAGRAM
THIS DIAGRAM IS FOR REFERENCE ONLY! ATTEMPTING
REPAIR BY UNQUALIFIED PERSONS MAY RESULT IN
SERIOUS INJURY OR EVEN DEATH.
NEVER ATTEMPT TO REPAIR OR SERVICE A MACHINE
ON YOUR OWN. REPAIRS SHOULD ONLY BE CONDUCTED
BY A QUALIFIED SERVICE PERSON OR ELECTRICIAN.
DO NOT MODIFY ANY PART OF THIS MACHINE. ALWAYS
UNPLUG BEFORE MAINTENANCE OR CLEANING.
6.5. SERVICE AND EXPART POINT
REMTA MAKİNA İTH. İHR. SAN. ve TİC. LTD. ŞTİ.
Adres: Akçaburgaz Mah. 4. Cad. 153. Sok. No:23 Esenyurt / İstanbul
Tel: [phone]
[email protected] • www.remta.com.tr
You can find all comunication information about our services in the link below.
www.remta.com.tr/yetkili-servisler