Renac WiFi Module User manual

Renac Power Technology Co.,Ltd.
+ Add: Building 6,No. 2,West Jinzhi Road,High-Tech District ,Suzhou City,Jiangsu Province,China
+ Web: www.renacpower.com
+ Email: [e-mail]
WiFi Module User manual
WiFi Module User manual
V1.0
V2.0

Android IOS
1. Installation
2. Download & Install Mobile APP
1. Insert the WIFI module into the COM port of the inverter
2. Tighten the fixing bolts on the module clockwise
3. Power on inverter.
There are two ways to download renac portal:
a. Download and install <Renac Portal> mobile app by scanning the QR code below
b. Download <Renac Portal> from Apple Store / Google Play
RENAC.

RENAC.
Install <Renac Portal> & Enable Permissions
When the user installs the APP for the first time, please set all the permissions of the APP to be enabled in the ‘’Settings’’-‘’Apps’’-‘’Permissions’’, so that the
SSID can be obtained correctly during WIFI setting.

3.1 Enter APP and enter the account & password
to enter the system. If no, please click [Register]
in the red box to register a new account.
3.2 After entering the system, click [+] in the red
box in the upper right corner to add a new power
station.
3.3 Add the power station page, fill in the
corresponding information, click [Add station] at
the bottom to add a new power station (For
"installer" item can be ignored. If you want to link
to one installer account, you can enter the installer
account name .All options with red* is required)
RENAC.
3. Device Registration

3.4 After adding the power station, jump to the
power station overview page and click on the
newly added power station name, as shown in
the following figure [Green Energy], enter the
device overview interface.
3.5 On the Device Overview page, also click on
the [+] in the upper right corner to register the
new device.
3.6. Locate the electrical label on the inverter,
enter the serial number of the device under the
Electrical label in the device registration page
SN (support automatic scanning with the camera),
then click on the blank space of the page, the
device information is automatically filled in, and
then click [Add Device] to complete the device
Registration operation
RENAC.
Inverter serial number

4. Reset WIFI module
5. WIFI Setting
When the WIFI module needs to reconnect to the new WIFI Router, press and hold
the reset button on the module for more than 5 seconds, the orange indicator will
flash, the module resets successfully, The Reset button as shown in the figure below.
Reset Button
RENAC.
5.1Make sure there is a good WIFI router signal
overlay near the inverter, turn on the mobile phone's
WALN switch, and connect the client’s WIFI router.
5.2 Open the Renac Portal, On the power station
overview page, click [WIFI Setting] in the red frame.
5.3. The WIFI setting will automatically get the SSID
(WIFI router’s name). Enter the password of WIFI
router and click [START]. A few seconds after shows
“Success config!’’, the yellow light of the WIFI module
stops flashing .It means the WIFI module was
configured successfully.

RENAC.
● Indicator Light Status:
Note : If the user enters the PV monitoring system for the first time
within 10 minutes after completing the above settings, please check
the live status interface in Renac Portal . If the data of the real-time
status interface is displayed, the network settings and other connections
of the data acquisition module are successful.
The following pic shows data
upload successfully:
Indicator light Yellow Flashing Yellow Stay on
Status Enter configuration mode WIFI module is configured

RENAC.
Contact Us
If you have technical questions about our products, please contact the Renac service hotline .We need the following information to provide you
with the necessary assistance:
Copyright © 2019 Jiangsu RENAC Power Technology Co., LTD
Add: Block6, No.2, West Jinzhi Rd, Suzhou National Hi-Tech District, Suzhou, China
Phone ：[phone]
Website：www.renacpower.com
Email: [e-mail]
The serial number of the collection box module
Inverter SN and model
User name and power station name