Renu Electronics WP6070CN-M Plus User manual

0
WP6070CN-M Plus
WP6101CN-M Plus
Product Code
WP6070CN-M Plus: 7”, 1024 x 600 pixels, WSVGA color
TFT with capacitive touch screen with serial port, 1
Ethernet port.
WP6101CN-M Plus: 10.1”, 1024 x 600 pixels, WSVGA
color TFT with capacitive touch screen with serial port, 1
Ethernet port.
The WP6CN-M Plus is a ThinClient with an inbuilt
browser, which can be used to connect to a remote web
server on the network.
To use the WP6 Plus as a browser, follow these steps to
connect the device to a webserver. The Password for
configuring the device is admin@123.
[Note: For configuring new Password it must be at least 7
or more characters with 1 capital letter (0-9, a-z, A-Z).]
1. Connect an Ethernet cable to the device.
2. Power up the device using 24VDC power supply by
connecting it to the device’s pluggable terminal block.
3. If the browser or the firmware needs to be updated,
connect a USB flash drive to the device.
Power
7.0“: 24VDC(±15%) @800mA,
19.2W
10.1“: 24VDC(±15%) @780mA,
18.72W
Display
1024 x 600pixels, 7" Color TFT,
WSVGA Web Panel capacitive
Touch Screen
1024 x 600pixels, 10.1" Color TFT,
WSVGA Web Panel capacitive
Touch Screen
Brightness
1000 Nits
Memory
eMMC: 4GB
RAM: 1GB
Panel Cutout
134.80(H) x 202.10(W) mm
187.90 (H) x 269.30(W) mm
Dimensions
146.20(H) x 213.50(W) x 46.80(D) mm
199.30(H) x 280.70(W) x 46.70(D) mm
Weight
7": 1000g
10.1": 1535g
Communication
USB Device
1x USB Type-C
USB Host
2 x USB 2.0
Ethernet
2 x 10/100MBps (One 10/100/1000
Mbps and one 10/100 Mbps)
Environment & Approvals
Operating Temperature
-20°C to 70°C
Storage Temperature
-20°C to 70°C
Humidity
10 to 95% (Noncondensing)
Shock
IEC 60068-2-27, 25g, 11ms, 6
shocks per axis, total 18 shocks (X,
Y, Z)
Vibration
5~150Hz, 3g peak, (X, Y, Z)
Protection
IP66 for front panel mounting
Approvals
RoHS compliant
Supported Web Server#
Codesys, Ignition SCADA, Node-
RED, Apache, Spider Controls
#Codesys, Ignition Scada, Google, Chromium, Apache, Node-RED etc. are
registered trademarks of their respective owners and Renu electronics does
not claim any rights over them
Specification
QUICK START GUIDE
WP6CN-M Plus Web
Panel
Panel Dimensions
GETTING STARTED

Earthing
The optimum method for earthing electronic equipment is
to earth it separately from other high-power systems, to
earth more than one unit of electronic equipment with a
single-point earth. The earthing marked terminal (see
below) is provided on the unit.
[Note: Do not use an earth that has an unstable
impedance, such as painted screws or earth subject to
vibration.]
Rev.
Description
Date
1.0
Initial Release
30/10/2023
RENU Electronics Pvt. Ltd®reserves the right to change
or discontinue specifications and features without prior
notice.
To view the latest and updated datasheets/manuals,
please visit www.renuelectronics.com.
Communication
WP6070CN-M Plus
Panel Cutout Dimensions: 134.80(H) x 202.10(W) mm
Panel Thickness: Maximum 6mm
Mounting Clamps: 4
WP6101CN-M Plus
Panel Cutout Dimensions: 187.90 (H) x 269.30(W) mm
Panel Thickness: Maximum 6mm
Mounting Clamps: 6
Tighten the mounting screws evenly to a torque
between 0.4N/m to maintain water and dust resistance.
This section provides information regarding
communication interfaces supported by this product.
Type C USB Port
The WP6CN-M Plus comes with a Type-C USB port.
Ethernet Port
The WP6CN-M Plus series devices come with an in-built
Ethernet port.
1. Fully compliant with IEEE 802.3 / 802.3U standards.
2. 10/100/1000 Mbps support.
3. Connector used: Standard shielded RJ-45 female
jack with in-built speed and link activity indication
LEDs.
Pin number
Signal
1
TX+
2
TX-
3
RX+
4
NC
5
NC
6
RX-
7
NC
8
NC
USB Host Port
The WP6CN-M Plus devices support one USB Host port
that connects to a USB 2.0 compatible USB Flash drive.
This port can be used to upgrade the firmware and the
browser.
Pin number
Signal
1
VCC
2
D-
3
D+
4
GND
Default Product Settings
Network Settings
DHCP
Brightness
Full Scale
Screen Touch Beeper
On
Default Language
English
Revision History