Renu Electronics WP6CN-M Plus User manual

0
WP2043CN
WP2070CN
WP2101CTN
Product Code
WP2043CN: 4.3”, 480 x 272 pixels, WSVGA color TFT
with 4-wire capacitive touch screen with serial port, 1
Ethernet port.
WP2070CN: 7”, 1024 x 600 pixels, WSVGA color TFT
with 4-wire capacitive touch screen with serial port, 1
Ethernet port.
WP2101CN: 10.1”, 1024 x 600 pixels, WSVGA color TFT
with 4-wire capacitive touch screen with serial port, 1
Ethernet port.
WP2 Lite web panel is a Thin Client with an inbuilt Micro
browser ready to connect to a remote web server on the
network.
To use the WP2 PCAP as a browser, follow these steps
to connect the device to a Webserver.
1. Power ON the WP2 Lite panel using a 24VDC power
supply.
2. Plug in the Ethernet cable into the RJ45 port.
3. After the device boots up, click on Settings 
Microbrowser and Network Settings.
4. On the new screen enter the Host address and the
start page on the host
Eg: Host: 192.168.1.50
Start Page: start.html
5. Click Back to go to the main page.
6. Click Start to load the web page.
Power (Base)
4.3“: 24VDC(±15%) @360mA,
8.64W
7.0“: 24VDC(±15%) @560mA,
13.44W
10.1“: 24VDC(±15%) 540@mA,
12.96W
Display
480 x 272pixels , 4.3" Color TFT,
WSVGA Web Panel capacitive
Touch Screen
1024 x 600pixels , 7" Color TFT,
WSVGA Web Panel capacitive
Touch Screen
1024 x 600pixels , 10.1" Color
TFT, WSVGA Web Panel
capacitive Touch Screen
Brightness
1000 Nits
Memory
CPU: 32-bit ARM Cortex-M7
RAM: 32MB
Panel Cutout
80(H) x 111(W)mm
127(H) x 175(W) mm
178(H) x 256(W) mm
Dimensions
89(H) x 120(W) x 31.5(D) mm
138(H) x 186(W) x 31(D) mm
190(H) x 268(W) x 33(D) mm
Weight
Approx. 200gm, 400gm, 900gm
LED
1
Communication
Ethernet
1x10/100MBps
OSK
Yes
Environment & Approvals
Operating Temperature
0°C to 50°C
Storage Temperature
-20°C to 85°C
Humidity
10 to 95% (Non-condensing)
Shock
IEC 60068-2-27, 25g, 11ms, 6
shocks per axis, total 18 shocks
(X, Y, Z)
Vibration
5~150Hz, 3g peak, (X, Y, Z)
Protection
IP66 for front panel mounting
Approvals
RoHS compliant
Supported Web Server
Spider Controls, Codesys2.x,
Codesys3.x
Specification
QUICK START GUIDE
WP2CN Lite Web Panel
Getting Started
Panel Dimensions

Rev.
Description
Date
1.0
Initial Release
30/10/2023
RENU Electronics Pvt. Ltd®reserves the right to change
or discontinue specifications and features without prior
notice.
To view the latest and updated datasheets/manuals,
please visit www.renuelectronics.com.
Communication
WP2043CN
Panel Cutout Dimensions: 111.00 (W) x 80.00(H) mm
Panel Thickness: Maximum 6mm
Mounting Clamps: 2
WP2070CN
Panel Cutout Dimensions: 127.00(H) x 175.00(W) mm
Panel Thickness: Maximum 6mm
Mounting Clamps: 4
WP2101CN
Panel Cutout Dimensions: 256.00 (W) x 178.00(H) mm
Panel Thickness: Maximum 6mm
Mounting Clamps: 6
Tighten the mounting screws evenly to a torque
between 0.4N/m to maintain water and dust resistance.
This section provides information regarding
communication interfaces supported by this product.
RJ45/Ethernet Port
The WP6 Plus series devices come with an in-built
RJ45/Ethernet port. The RJ45 port is a shielded female
jack with link and activity LEDs.
Pin number
Signal
1
TX+
2
TX-
3
RX+
4
NC
5
NC
6
RX-
7
NC
8
NC
Earthing
The optimum method for earthing electronic equipment is
to earth it separately from other high-power systems, to
earth more than one unit of electronic equipment with a
single-point earth. The earthing marked terminal (see
below) is provided on the unit.
[Note: Do not use an earth that has an unstable
impedance, such as painted screws or earth subject to
vibration.]
Revision History
WARNING
This equipment is suitable for use in Class I, Division 2,
Groups A, B, C and D or non-hazardous locations only.
WARNING - EXPLOSION HAZARD - Do not disconnect
equipment unless power has been removed or the area
is known to be non- hazardous.
WARNING - EXPLOSION HAZARD - Substitution of
components may impair suitability for Class I, Division 2.
The list of materials used in the construction of these
devices with name of sealed device - generic name of
the material and the supplier's name and type
designation.
It is recommended that the user periodically inspect the
sealed devices used, for any degradation of properties
and Replace the device ifany degradation is found.