REO REOVIB MFS 268 User manual

MFS_268_EtherNetIP_appendix_rev03.en
02.08.2016
REOVIB
Control Equipment for the Vibratory Feeder Industry
MFS 26
Frequency Converter for Vibratory Feeders
Appendix: EtherNet-IP - Programming

REOVIB MFS 26
Operating Instru tions EtherNet/IP - Programming
2
Technical safety instructions for the user
This des ription ontains the ne essary information for the orre t appli ation of the produ t des ribed
below. It is intended for use by te hni ally qualified personal.
Qualified personnel are persons who, be ause of their training, experien e and position as well as their
knowledge of appropriate standards, regulations, health and safety requirements and working onditions,
are authorised to be responsible for the safety of the equipment, at all times, whilst arrying out their nor-
mal duties and are therefore aware of, and an report, possible hazards (Definition of qualified employees
a ording to IEC 364)
Safety Instructions
The following instru tions are provided for the personal safety of operators and also for the prote tion of
the des ribed produ t and onne ted equipment.
Warning!
Hazardous Voltage
Failure to observe an kill, ause serious injury or damage
• Isolate from mains before installation or dismantling work, as well as for fuse hanges or post installa-
tion modifi ations.
• Observe the pres ribed a ident prevention and safety rules for the spe ifi appli ation.
• Before putting into operation he k if the rated voltage for the unit onforms with the lo al supply
voltage.
• Emergen y stop devi es must be provided for all appli ations. Operation of the emergen y stop must
inhibit any further un ontrolled operation.
• The electrical connecting terminals must be covered!
• Earth bonding must be tested for integrity after installation.
Specified Use
The units des ribed herein are ele tri al ontrollers for installation in industrial plant.
They are designed for ontrolling vibratory feeders.
!

REOVIB MFS 26
Operating Instru tions EtherNet/IP - Programming
3
Contents
Te hni al safety instru tions for the user ..................................................................................................... 2
1.0 General ................................................................................................................................................... 4
2.0 Interfa e operation (EtherNet-IP ) .......................................................................................................... 5
3.0 A tivate interfa e .................................................................................................................................... 5
4.0 EDS-File ................................................................................................................................................. 5
5.0 Bus operating modes.............................................................................................................................. 5
5.1 Programming for the Bus operation .................................................................................................... 6
5.1.1 Send to Controller ........................................................................................................................ 6
5.1.2 Reply from Controller ................................................................................................................... 6
5.2 Parameter Operation .......................................................................................................................... 7
5.2.1 Creating parameter addresses and values .................................................................................. 7
5.2.2 Send Write Enable ....................................................................................................................... 7
5.2.3 Re eive, A knowledge Write Enable ........................................................................................... 8
5.2.4 Send Parameter ........................................................................................................................... 8
5.2.5 Close write enable ........................................................................................................................ 9
5.2.6 Parameter read (send) ................................................................................................................. 9
6.0 Parameter Table ................................................................................................................................... 10
7.0 Example of bus ommuni ation with Frequen y ontroller .................................................................. 12
7.1 Normal mode .................................................................................................................................... 12
7.2 Parameter mode ............................................................................................................................... 12
7.3 RESET Controller ............................................................................................................................. 14
8.0 Methods for adjusting the IP-address ................................................................................................... 15
8.1 Web server ........................................................................................................................................ 15
8.2 DHCP Server Utility (Example: „BOOTP/DHCP Server“) ................................................................. 17

REOVIB MFS 26
Operating Instru tions EtherNet/IP - Programming
4
1.0 General
The MFS 268 range of frequen y onverters for vibratory feeders an operate with an EtherNet-IP inter-
fa e.
In normal operation the set point, for the feeder throughput, an be sent from a PLC to the ontroller and
the unit ready/fault status signals are fed ba k. In an additional parameter mode the unit an be onfig-
ured over the EtherNet-IP. An external power supply of 24 VDC is required for the interfa e.
The required EDS-File is provided at the time of delivery.
+24V DC
swit h
reset IP
input
EIP
output
EIP
LED I
blinks during a tive internal
ommuni ation
green LED: EtherNet ok
yellow LED: Bus error
green LED: EtherNet ok
yellow LED: status-LED
The interfa e enables ommuni ation with the frequen y onverter, using 4 data words (i.e. 16 Bits).
The four 16 Bit words are transmitted and a knowledged every bus y le.
! Important – Data consistence is required to operate with EtherNet-IP!
Note: Data consistence is defined in a Siemens S7 PLC with SFC14 and SFC15, for example
Units are fa tory set prior to delivery and so are onfigured for bus operation.
If the unit is required for manual ontrol then the parameter “CAN.” in menu C 017 should be set on “0”.
You get ba k to bus operation, if you hoose CAN. = „1“.

REOVIB MFS 26
Operating Instru tions EtherNet/IP - Programming
5
2.0 Interface operation (EtherNet-IP )
Bus Power Supply 24 V, DC, 250 mA
Bus onne tor 2 x RJ-45
Internal interfa e CAN-Bus
Supported baud rates 1000 kBaud
Communi ation Data onsisten y required
Proto ol EtherNet-IP
3.0 Activate interface
For the interfa e version parameter “CAN” is set to “I”. Then ommuni ation through the interfa e is pos-
sible. If manual ontrol of the unit should be required e.g. for testing, this parameter must firstly be set
ba k to "0” again.
Important: The parameter “Ad.” must be set to “1” and the baud rate must be set to “b 1000”.
Code 017
0 = interfa e off
I = interfa e on
P
P
running mode
P
P
P
P
P
P
4.0 EDS-File
Following EDS-File is required for the operation with the EtherNet-IP interfa e:
EDS File Name
:
UNIGATE IC
-
EI 2Port.eds
The EDS-file is supplied on a CD with each new unit or alternatively, visit www.reo.de to download
the file from the website.
5.0 Bus operating modes
Two fundamental operating modes an be hosen for bus ommuni ation.
Normal Operation: Control of the frequen y ontroller in produ tion, in whi h ase the Set point and
ON/OFF ontrol signals are transmitted
Parameter Operation: Adjustment of the frequen y ontroller for the desired operation mode and limits.
In a spe ial mode the parameter and parameter addresses are transmitted and
a knowledged.
In parameter operation, the unit’s spe ifi values, su h as frequen y, soft start
time, timers and swit hing et ., are set.

REOVIB MFS 26
Operating Instru tions EtherNet/IP - Programming
6
5.1 Programming for the Bus operation
In normal operation the set point for Amplitude (throughout/feed rate) and the digital ontrol signals, su h
as enable are set a ross the interfa e. The a tual voltage/ urrent values and unit status (ready or fault)
are fed ba k. All data words are within the range 0…FFFF H.
The following ommuni ation words are given in bit form.
5.1.1 Send to Controller
H-Byte L-Byte
Wor
d
1
0000 H (reserved)
15 14 13
12 11 10
9 8 7 6 5 4 3 2 1 0
H-Byte L-Byte
Word
2
Set point 1, 16-Bit 100 % = FFFF H
15 14 13
12 11 10
9 8 7 6 5 4 3 2 1 0
H-Byte L-Byte
Word
3
reserved
15 14 13
12 11 10
9 8 7 6 5 4 3 2 1 0
H-Byte L-Byte
Word
4
Control - word
Bit = „1“ = Function ON
All unused bits MUST be set to `0`
15 14 13
12 11 10
9 8 7 6 5 4 3 2 1 0
0 Mode bit
0 0 0 0 0 0 0 0 0 0 0 0 0 Enable 0 0
Control information (unit spe ifi )
5.1.2 Reply from Controller
H-Byte L-Byte
Wor
d
1
xxxx H (undefined)
15 14 13
12 11 10
9 8 7 6 5 4 3 2 1 0
H-Byte L-Byte
Word
2
(
only in regulation mode
)
Feed ba k a tual a eleration
16 Bit 100% = 8000H
15 14 13
12 11 10
9 8 7 6 5 4 3 2 1 0
H-Byte L-Byte
Word
3
Feed ba k a tual output urrent,
16 Bit 100% = 8000H (in % von I-nom)
15 14 13
12 11 10
9 8 7 6 5 4 3 2 1 0
H-Byte L-Byte
Word
4
Status - Word
X = Not defined
Bit = „1“ = Fun tion ON
15 14 13
12 11 10
9 8 7 6 5 4 3 2 1 0
Status - Code
ERROR - Code
X
X
X
OFF
X
X
X
X
Status information
Unit spe ifi
00
A5 (H)
57 (H)
58 (H)
02 (H)
0C (H)
05 (H)
C0 (H)
Unit not responding
Unit ready
ERROR Peak
ERROR OC
ERROR OL
ERROR ACC
ERROR OU
A knowledge
Parameter mode
Status, a tual a eleration and a tual output urrent are re eived.
0 = Normal operation
1 = Parameter operation Enable - bit
OFF – Bit
A knowledge

REOVIB MFS 26
Operating Instru tions EtherNet/IP - Programming
7
5.2 Parameter Operation
In parameter operation, the spe ifi unit parameters an be monitored and adjusted.
A `write` enable must be transmitted before parameters an be altered. On losing, the `write` enable
must be an elled.
A `read` request must be sent before data an be read.
Word 3 in the a knowledge is always `C0DE H`. This indi ates that the ontroller is in parameter mode.
5.2.1 Creating parameter addresses and values
In parameter operation the most signifi ant bit (msb) in Word 1 is defined as a read or write bit (R/W),
where 1 = write and 0 = read, this should be a ompanied by the orresponding parameter address.
The mode bit (msb in Word 3) is used to sele t normal or parameter operation, 0 = Normal or 1 = pa-
rameter operation.
Word 1:
reserved
0000
H
Word 2
:
R / W
–
Bit + Address
e.g. 000 H + 1009 H => 9009 H
Word 3
:
Value of the parameters
e.g. 7FFF H
Word 4
:
Mode bit = 1 + Control bit’s
e.g. 000 H + 0004 H => 9004 H
5.2.2 Send Write Enable
H-Byte L-Byte
Wor
d
1
0000 H (reserved)
15
14 13 12
11 10 9 8 7 6 5 4 3 2 1 0
H-Byte L-Byte
Word
2
Write Enable Address = C0DE H
C0
DE
H-Byte L-Byte
Word
3
Write Enable = B5E7 H
B5 E7
H-Byte L-Byte
Word
4
Control - Word + 8000 H
Mode Bit must be set to `1` !!
All unused bits must be set to `0`
Bit = `1` = Fun tion ON
15
14 13 12
11 10 9 8 7 6 5 4 3 2 1 0
1 Mode bit 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Control Information unit spe ifi

REOVIB MFS 26
Operating Instru tions EtherNet/IP - Programming
8
5.2.3 Receive, Acknowledge Write Enable
H-Byte L-Byte
Wor
d
1
xxxx H (undefined)
0
0
0
E
H-Byte L-Byte
Wo
rd
2
C0DE H
C0
DE
H-Byte L-Byte
W
ord
3
B5E7 H
B5
E7
H-Byte L-Byte
Word
4
C0DE H
C0
DE
The parameters an be sent after re eipt of the a knowledge
5.2.4 Send Parameter
H-Byte L-Byte
Wor
d
1
0000 H (reserve)
15 14 13
12 11 10
9 8 7 6 5 4 3 2 1 0
H-Byte L-Byte
Word
2
Parameter address + R / W – Bit
(16-Bit) = 0...FFFF H
15 14 13
12 11 10
9 8 7 6 5 4 3 2 1 0
R / W
Parameter address
H-Byte L-Byte
Word
3
Parameter value
(16-Bit) = 0...FFFF H
XX XX
H-Byte L-Byte
Word
4
Control - Word + 8000H
Mode must be set to `1`!!
All unused bits must be set to `0`
Bit = `1` = Fun tion ON
15 14 13
12 11 10
9 8 7 6 5 4 3 2 1 0
1 Mode bit 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Control Information (unit spe ifi )
Received acknowledge
H-Byte L-Byte
Wor
d
1
xxxx H
0
0
00
H-Byte L-Byte
Word
2
A knowledge the sent address
+ R / W - Bit
15 14 13
12 11 10
9 8 7 6 5 4 3 2 1 0
R / W
Parameter address
H-Byte L-Byte
Word
3
Acknowledge the Parameter value
XX XX
H-Byte L-Byte
Word
4
A knowledge the Parameter mode
(always „C0DE“ H)
C0
DE

REOVIB MFS 26
Operating Instru tions EtherNet/IP - Programming
9
5.2.5 Close write enable
H-Byte L-Byte
Wort
d
0000 H
0
0
0
0
H-Byte L-Byte
Word
2
Write Enable Address = C0DE H
C0
DE
H-Byte L-Byte
Word
3
Enable Value 0000
00 00
H-Byte L-Byte
Word
4
Control - Word + 8000 H
Mode bit must be set to `1`!
All unused bits must be set to `0`
Bit = `1` = Fun tion ON
15
14 13 12
11 10 9 8 7 6 5 4 3 2 1 0
1 Mode bit 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Control Information (unit spe ifi )
5.2.6 Parameter read (send)
H-Byte L-Byte
Wort
d
xxxx H (undefined)
0
0
0
0
H-Byte L-Byte
Word
2
Parameter address + R / W - Bit
15
14 13 12
11 10 9 8 7 6 5 4 3 2 1 0
R / W
Parameter address
H-Byte L-Byte
Word
3
Read Enable Value = 0000
00
00
H-Byte L-Byte
Word
4
Mode bit = 1 + Control bits
0
00
Received parameter
H-Byte L-Byte
Wor
d
1
xxxx H (undefined)
0
0
0
0
H-Byte L-Byte
Word
2
A knowledge
Parameter address + R / W - Bit
15
14 13 12
11 10 9 8 7 6 5 4 3 2 1 0
R / W
Parameter address
H-Byte L-Byte
Word
3
Parameter value
XX
XX
H-Byte L-Byte
Word
4
A kowledge Parameter mode
C0
DE

REOVIB MFS 26
Operating Instru tions EtherNet/IP - Programming
10
6.0 Parameter Table
Non listed addresses annot be altered!
Parameter: Adjustment Display-
Code
Fa tory
Setting:
Entry
ode
Parameter
address
HEX (.bit)
Value
HEX
Vibratory feeder
• Amplitude (throughput) 0...100 % A. 0 % 000,
002,
008, 096
100C
0x0000...0xFFFF
• Se ond set point / oarse - fine 0…100 % 2. 0 002 0x1006
0x0000...0xFFFF
• Maximum ontrol limit (U
max
) 5...100 % P. 90 % 096, 008
1009
0CCC...FFFF H
• Vibrating frequen y
5...300 Hz F. 100 Hz 096, 008
040
1005
01F4...7530 H
500...30000 de .
(FL.)...(FH.)
• Soft start ramp up 0...60 se . /. 0,1 se . 096 1013
0x0000...0xFFFF
• Soft stop ramp down 0...60 se . \. 0,1 se . 096 1012
0x0000...0xFFFF
• Swit h to external set point 0 / I E.S.P. 0 003 0x5800
0x0000 / 0x FFFF
• Set point 0(4)...20 mA 0 / I 4.20 0 003 0x5801
0x0000 / 0x FFFF
• Potentiometer set point
(for 3 / 6 / 8 A units)
0 / I POT. 0 003 0x5805
0x0000 / 0x FFFF
• Coarse / Fine ontrol 0 / I S.P.2. 0 003 0x580C
0x0000 / 0x FFFF
• Swit h to se ond set point (delayed) 0 / I S.2.d 0 003
0x0000 / 0x FFFF
• Invert enable 0 / I -En. 0 003 0x5811
0x0000 / 0x FFFF
• Swit h status/ ready relay 0 / I r.b. 0 003 0x583D
0x0000 / 0x FFFF
Regulation (with sensor)
• Swit h to regulation 0 / I ACC. 0 008 0x5808
0x0000 / 0x FFFF
• P hara teristi 0...100 P.A. 40 008 0x100F
0x0000...0xFFFF
• I hara teristi 0...100 I.A. 100 008 0x1014
0x0000...0xFFFF
• Automati frequen y ontrol 0 / I A.F.C. 0 008 0x5809
0x0000 / 0x FFFF
• Start automati frequen y sear h start A.F.S. 008 0x1400
0x0AF5
Track control
• Swit h on time delay 0...60 se . I. 1 se . 007, 167
0x1003
0x0000...0xFFFF
• Swit h off time delay 0...60 se . O. 1 se . 007, 167
0x1002
0x0000...0xFFFF
• Invert sensor PNP / PNP
inverse
-SE. 0 007, 167
0x580A
0x0000 / 0x FFFF
Sensor control
• Sensor Time-out 0 / I E.En 0 015, 167
0x580B
0x0000 / 0x FFFF
• Sense time delay (Sensor Time-out) 30...240
se .
E. 180 se . 015, 167
0x1004
0x0000...0xFFFF
• lead time valve output
1)
0…60 se . A.r. 0,0 015
0x0000...0xFFFF
• follow-up time valve output
1)
0…60 se . Ai. 4,0 015 0x102C
0x0000...0xFFFF
Interface (option)
• Interfa e OFF / ON 0 / I An. I 017 0x5818
0x0000 / 0x FFFF
Service
• ERROR Reset Reset CLr.Er. 009 1400
C009 H
• Hide programming menus 0 / I Hd.C. 117 0x5804
0x0000 / 0x FFFF
• Choose user parameter menu
Nr. 0...3
0...3 U.S.I. 0 143
• Save user settings PUSH. 143
• Re all fa tory settings FAC. 210
• Choose user parameter menu
Nr. 0...3
0...3 U.S.I. 0 210
• Re all user parameter US.PA. 210

REOVIB MFS 26
Operating Instru tions EtherNet/IP - Programming
11
Parameter: Adjustment Display-
Code
Fa tory
Setting:
Entry
ode
Parameter
address
HEX (.bit)
Value
HEX
Service limits
• Enable servi e menu 0 / I En.S. 0 127 0x5834
0x0000 / 0x FFFF
• Show output urrent (0... 100 %) i. 040 0x200A
0x0000...0x8000 H
• Show a tive vibration frequen y F. 040 0x1005
0x01F4...0x7530 H
• Current limit 0...100 % I. 100 040 0x1016
0x0000...0x8000 H
• Stop at urrent limit 0 / I E.F.u. 0 040 0x5850
0x0000 / 0x FFFF
• Current regulator P-part 1…100 I.P. 20 040 0x100D
0x0000...0xFFFF
• Current regulator I-part 1…100 I.I 40 040 0x1032
0x0000...0xFFFF
• Min frequen y limit 5...150 Hz
F.L: 35 040 0x1020
01F4...7530 H
500...30000 de .
• Max frequen y limit 5...150 Hz
F.H. 140 040 0x1021
01F4...7530 H
500...30000 de .
• Start level AFC 0…100 A.S. 25 040 0x1033
0x0000...0xFFFF
• Output voltage limited 0…100 P.L. 100 040 0x1018
0x0000...0xFFFF
1) Not available IP20 Version
2) Not for fieldbus operation

REOVIB MFS 26
Operating Instru tions EtherNet/IP - Programming
12
7.0 Example of bus communication with Frequency controller
Variable values are shown in italics.
7.1 Normal mode
(Set point to 70 %)
Send Set point
Word Code
send
Code
Received
1 0000 H
0000 H
2 B332 H
Set point = 70 %
--- ---
3
4 4 H Enable On A5xx H Ready
Enable ON, Stop ontroller (with enable)
Send Set point
Word Code
send
Code
Received
1 0000 H
0000 H
2 B332 H
Set point = 70 %
--- ---
3
4 H Enable OFF A5xx H Ready
7.2 Parameter mode
(e.g. set frequen y to 50 Hz and soft start to 2 se ond)
Open write
enable
Word Code
send
Code
Received
1 0000 H
0000 H
2 C0DE H Write enable Address C0DE H A knowledge
3 B5E7 H Write enable value B5E7 H A knowledge
4 8000 H +
Control bits
Set mode bit = 1 C0DE H A knowledge
Write param
eter
1 0000 H
0000 H
2 9 5 H Parameter address
Vibrating frequen y
+ R / W - Bit
9 5 H A knowledge
3 1388H
Frequency 50 Hz
1388 H A knowledge 50 Hz
4 8000 H +
Control bits
Set mode bit = 1 C0DE H A knowledge
Write param
eter
1 0000 H
0000 H
2 9 13 H Parameter address
Soft start
+ R / W - Bit
9 13 H A knowledge
3 3333 H
Soft start 2 Sec.
3333 H A knowledge 2 se onds
4 8000 H +
Control bits
Set mode bit = 1 C0DE H A knowledge
Close Write
enable
Word Code
send
Code
Received
1 0000 H
0000 H
2 C0DE H Write enable address C0DE H A knowledge
3 0000 H Write enable Value 0000 H A knowledge
4 8000 H +
Control bits
Set mode bit = 1 C0DE H A knowledge

REOVIB MFS 26
Operating Instru tions EtherNet/IP - Programming
13
Example of swit h parameter hange
Enable invert
Open
Write enable
Word Code
send
Code
Received
1 0000 H
0000 H
2 C0DE H Write Enable Address C0DE H A knowledge
3 B5E7 H Write Enable Value B5E7 H A knowledge
4 8000 H +
Control bits
Set mode bit = 1 C0DE H A knowledge
Write Parameter
1 0000 H
0000 H
2 D811 H Parameter address
D811 H A knowledge
3 FFFF H new Parameter FFFF H A knowledge
4 8000 H +
Control bits
Set mode bit = 1 C0DE H A knowledge
Close Write enable
Word Code
send
Code
Received
1 0000 H
0000 H
2 C0DE H Write Enable Address C0DE H A knowledge
3 0000 H Write Enable Value 0000 H A knowledge
4 8000 H +
Control bits
Set mode bit = 1 C0DE H A knowledge
Read only the parameter)
Read
Word Code
send
Code
Received
1 0000 H
0000 H
2 1 13 H Parameter address
Soft start
1013 H A knowledge
3 0000 H Read parameter 8 H Parameter value ( => 5 se onds)
4 8000 H +
Control bits
Set mode bit = 1 C0DE H A knowledge Parameter mode

REOVIB MFS 26
Operating Instru tions EtherNet/IP - Programming
14
7.3 RESET Controller
Open
Write e
n
able
Word Code
send
Code
received
1 0000 H
0000 H
2 C0DE H Write Enable Address C0DE H A knowledge
3 B5C9 H Write Enable Value B5C9 H A knowledge
4 8000 H +
Control bits
Set mode bit = 1 C0DE H A knowledge
Write Parameter
1 0000 H
0000 H
2 94 H Parameter address
Reset
+ R / W - Bit
H A knowledge
3 C 9 H RESET. H
4 8000 H +
Control bits
Set mode bit = 1 C0DE H
Allow approximately 0.5 se . for RESET

REOVIB MFS 26
Operating Instru tions EtherNet/IP - Programming
15
.0 Methods for adjusting the IP-address
1. Web server (Preferably)
2. DHCP Server Utility
If you don’t have a browser, you an push a swit h on the front of our devi e.
If you push this swit h shorter than five se onds, the devi e gets the IP-address 192.168.11.182.
If you push this swit h longer than five se onds, the devi e is set into the original state (IP-address
0.0.0.0) and DHCP is set on.
.1 Web server
You an all up an HTML-page with the help of our web server. There are shown system parameters of
the devi e on this page.
If the subnet mask of your PC doesn’t orrespond with the subnet mask of the devi e, you pro eed in the
following way.
1. You open the ontrol panel.
2. There you open the “Network and Sharing Center”.
3. There you li k on “LAN-Verbindung” respe tively „LAN- onne tions“.
4. There you hoose “Properties”.

REOVIB MFS 26
Operating Instru tions EtherNet/IP - Programming
16
5. Then you double- li k on „Internet Proto ol Version 4 (TCP/IPv4)“
6. Then you set the subnet mask at 255.255.240.0.
7. You li k on „OK“.
8. Then you open the web browser (e.g. the Internet-Explorer).
9. You enter the following IP-address 192.168.11.182 as address.
10. Then you li k on „IP-Set“.

REOVIB MFS 26
Operating Instru tions EtherNet/IP - Programming
17
.2 DHCP Server Utility (Example: „BOOTP/DHCP Server“)
1. Please download a DHCP Server software for example: „DHCP/BOOTP Utility“.
Important: Before you start the DHCP-server, note the MAC-address whi h has the following
form: 00-00-BC-14-55-35. The MAC-address stands on the front of the module.
2. Start the DHCP-software.
3. You hoose „Network Settings“ in the menu „Tools“.
4. You enter the subnet mask.
5. The Gateway-address, Primary and/or Se ondary DNS-address and Domain Name are optional.
6. Choose the appropriate module.
7. Cli k on „Add to Relation List“. The „New Entry“ dialog box appears.
8. Enter an IP-address, host name and des ription for the module.
9. Cli k on „OK“.
10. You wait until the module appears in the „Relation List“. Then you hoose it. The onfiguration is
assigned permanently for the module this way.
11. Cli k „Disable BOOTP/DHCP“.
12. If the message „Command su essful“ appears, the onfiguration was su essful.

REOVIB MFS 26
Operating Instru tions EtherNet/IP - Programming
18

REOVIB MFS 26
Operating Instru tions EtherNet/IP - Programming
19

REO AG
Brühler Straße 100 · D-42657 Solingen
Tel.: [phone] · Fax: [phone]
E-Mail: i[email protected]
Internet: www.reo.de
PRODUCTION+SALES:
China
REO Shanghai Indu tive Components Co., Ltd
No. 536 ShangFeng Road · Pudong, 201201 Shanghai · China
Tel.: [phone] · Fax: [phone]
E-Mail: info@reo. n · Internet: www.reo. n
India
REO GPD INDUCTIVE COMPONENTS PVT. LTD
2/202 Luna Road · Village Luna · Taluka Padra
Vadodara - 391440 · India
Tel.: [phone]
E-Mail: info@reogpd. om · Internet: www.reo-ag.in
USA
REO-USA, In .
8450 E. 47th St · USA-Indianapolis, IN 46226
Tel.: [phone] · Fax: [phone]
E-Mail: info@reo-usa. om · Internet: www.reo-usa. om
SALES:
Fran e
REO VARIAC S.A.R.L.
ZAC Du Clos aux Pois 1 · 6/8 rue de la Closerie-LISSES· F-91048 Evry Cédex
Tel.: [phone] · Fax: [phone]
E-Mail: reovaria @reo.fr · Internet: www.reo.fr
Great Britain
REO (UK) Ltd.
Units 2-4 Callow Hill Road · Craven Arms · Shropshire SY7 8NT · UK
Tel.: [phone] · Fax: [phone]
E-Mail: main@reo. o.uk · Internet: www.reo. o.uk
Italy
REO ITALIA S.r.l.
Via Treponti, 29 · I-25086 Rezzato (BS)
Tel.: [phone] · Fax: [phone]
E-Mail: [email protected] · Internet: www.reoitalia.it
Poland
REO CROMA Sp.zo.o
ul. Pozaryskiego 28, bud 20 · PL-04-703 Warszawa
Tel.: [phone] · Fax: [phone]
E-Mail: roma@ roma. om.pl · Internet: www. roma. om.pl
Spain
REO ESPAÑA 2002 S.A.
C/Manuel Ventura i Campeny 21B · lo al 9 · E-08339 Vilassar de Dalt (Bar elona)
Tel.: [phone] · Fax: [phone]
E-Mail: info@reospain. om · Internet: www.reospain. om
Switzerland
REO ELEKTRONIK AG
Im Halbia ker 5a · CH-8352 Elsau
Tel.: [phone] · Fax: [phone]
E-Mail: info@reo. h · Internet: www.reo. h
Turkey
REOTURKEY ELEKTRONİK San. ve Ti . Ltd. Şti.
Halil Rıfatpasa Mah. · Darül eze CD Perpa Ti Merkezi
B Blok Kat 8 No:1095 · TR-34384 Sisli – Istanbul
Tel.: [phone] · Fax: [phone]
E-Mail: info@reo-turkey. om · Internet: www.reo-turkey. om
Divisions:
REO Vibratory Feeding and Power Ele troni s Division
Brühler Straße 100 · D-42657 Solingen
Tel.: [phone] · Fax: [phone]
E-Mail: [e-mail]
REO Train Te hnologies Division
Erasmusstraße 14 · D-10553 Berlin
Tel.: [phone] · Fax: [phone]
E-Mail: zentrale.b[email protected]
REO Drives Division
Holzhausener Straße 52
D-16866 Kyritz
Tel.: [phone] · Fax: [phone]
E-Mail: zentrale.k[email protected]
REO Medi al and Current Transformer Division
S huldholzinger Weg 7 · D-84347 Pfarrkir hen
Tel.: [phone] · Fax: [phone]
E-Mail: zentrale.pfarrkir [email protected]
REO Test and PowerQuality Division
Brühler Straße 100 · D-42657 Solingen
Tel.: [phone] · Fax: [phone]
E-Mail: [e-mail]