REPEATIT Trinity-323 User manual

Trinity-300 TDD Plus
Trinity-323 TDD
Trinity-323 TDD Plus
Trinity-323 TDD Plus Offshore
Quick Start Guide
The full manual can be retrieved from http://www.repeatit.se/support/trinity
Warning: This product transmits information using microwave radio signals. Installation of fixed
outdoor radio links should only be performed by a qualified and trained technician familiar with local
radio, electric and safety regulations.
Before proceeding with the installation verify that the equipment works on the ground. Power up
both units and put them between your computer and network access, you should have full
communication within a few minutes of powering up the units. (If the units have no internal antenna
make sure you place the antenna connectors directly opposite each other.)
The units are pre-configured and paired from factory with the following parameters.
Master Client
IP address 10.0.0.1 10.0.0.2
Username admin admin
Password public public
Installing the link
Mount the first unit, point it towards the site of the second unit. Power it up and make sure the
Power LED is lit and the status LED blinks slowly.
Mount the second unit. Power it up and adjust it for best signal using the status LED.
Adjust the first unit for best signal using the Status LED.
Make sure all cables are secured and connect the link to the network.
Configure the distance parameters at the master unit to reflect the correct distance between the
units.
Note Make sure that the polarization on both units are in the same direction. Unaligned
polarization will significantly reduce the signal strength.

Package contents
Trinity-300 TDD
Trinity-323 TDD / Trinity-323 TDD Plus /
Trinity-323 TDD Plus Offshore
2 Trinity-300 TDD units with N-female 2 Trinity-323 TDD units with integrated 23
antenna connector dBi antenna.
2 Mounting kits 2 Mounting kits.
2 PoE with power adapter for your local 2 PoE with power adapter for your local
region. region.
2 RJ-45 connector seals. 2 RJ-45 connector seals.

How to access the unit’s web interface
The unit does not have a DHCP server and will not provide any IP address to your PC when you
connect the Ethernet cable. To be able to access the unit, your PC needs to be configured with a
static IP address that is within the same subnet as the IP address of the unit.
To change the IP address of your network card you need to open the configuration utility for your
network card. For information on how to do that please consult you operating system manual.
The default IP settings of the units are:
IP Netmask
Master unit 10.0.0.1 255.0.0.0
Client unit 10.0.0.2 255.0.0.0
Recommended configuration of your network card is:
IP Netmask
10.0.0.3 255.0.0.0
You do not need to have a gateway address to configure the unit when you are connected directly
to it.
If you want the units to be accessible within your normal subnet you will have to reconfigure the
IP addresses of the units. Remember that after changing the IP address of the unit you will not be
able to access it again until you have reconfigured your network card to be in the same subnet as
you configured in the unit.
Note Your Trinity link will work as a cable replacement (transparent bridge), therefore you should
never connect both units to the same switch or Ethernet segment. Doing so will cause an infinite
forwarding loop which severely will disrupt normal traffic on your network.
Warning: At all times, it is the customer’s responsibility to ensure that an outdoor antenna
installation complies with local radio, electric and safety regulations.
If you are not certain about the regulations that apply in your country, consult your regulatory
agency or a local Sub10Systems-Repeatit sales partner.
The customer must verify that:
The installation is performed by a qualified technician.
The antenna installer is aware of local regulations and limits, including, but not limited to,
allowed frequency spectrum and maximum EIRP limits.
The final installation complies with local radio, electric and safety regulations, including, but
not limited to allowed frequency and maximum EIRP limit.
Repeatit AB and its resellers or distributors are not liable for any damage or violation of
government regulations that may arise from failing to comply with these guidelines.
Repeatit AB Tel: [phone]
Hamngatan 33 Fax: [phone]
172 66 Sundbyberg E-mail: [e-mail]
Sweden www.repeatit.se