Republic Storage Products 7002376/2019 User manual

INDUSTRIAL CLIP SHELVING ASSEMBLY INSTRUCTIONS #7002376/ 2019
3743 Boettler Oaks Drive (Suite A) Uniontown OH 44685 ---- 800.477.1255 ---- www.republicstorage.com
Clip to Post Connection
OPEN UNIT ASSEMBLY
1. The first and last uprights in a row of shelving are End Uprights. The remaining uprights in a row are
Intermediate Uprights (see assembly graphic above). To build the End Upright, lay the front and rear
post parallel to each other on the floor or saw horses. Position Angle Posts with the 1” flange pointing
up. The front post may be Beaded or Angle. The back post is always Angle.
Install Shelf Clips on both posts at the desired shelf locations by inserting the fingers of the clip into
the rectangular holes in the post and sliding down until the clip is fully seated. Install the clips for the
bottom shelf in the bottom two rectangular holes; install the clips for the top shelf in the top two
rectangular holes.
Using a shelf to determine proper spacing of posts, attach a pair of Side Sway Braces to the posts
forming an “X” with ¼-20 x 5/8” screws and nuts. See page 3 for information regarding sway brace locations. Note: Bolts cannot be placed where
shelves are located.
2. Intermediate Uprights are built like End Uprights, except Double Angle Posts replace Single Angle Posts (see graphic above). Double Angle Posts
are made by bolting two Single Angle Posts together with two ¼-20 x 5/8” screws and nuts. Install Shelf Clips on both sides of the post assembly.
Attach a pair of Sway Braces to the front and rear posts as in Step 1.
3. Stand two End Uprights or an End and Intermediate Upright to build the first unit. Hold the uprights in position and install the top and bottom shelves
on to the shelf clips. Make sure shelves are completely seated on the clips by tapping them down with a soft hammer. Repeat this process with the
rest of the shelves in the first unit.
4. While holding the unit vertical, install a pair of Back Sway Braces in an “X” pattern using ¼-20 x 5/8” screws and nuts. Attach the Back Sway Braces
on the inside of the rear Angle Posts as shown.
5. If building a row of shelving, continue to add units by standing additional upright assemblies and installing shelves and back braces. The last upright
in the row of shelving must be an End Upright.
6. Back to back (double) rows are built like single rows, except common Back Sway Braces are used. The common braces are installed on the inside of
one of the units, with the bolts going through both rear posts of the back to back units. This will securely tie the back to back units together.
Series 2000 Shelf
End Upright
(At row ends)
Angle
Post
Shelf
Clip
Side
Sway
Brace
Back Sway
Brace
Intermediate
Upright
Beaded Post
(Used at front
only)

INDUSTRIAL CLIP SHELVING ASSEMBLY INSTRUCTIONS #7002376/ 2019
3743 Boettler Oaks Drive (Suite A) Uniontown OH 44685 ---- 800.477.1255 ---- www.republicstorage.com
CLOSED UNIT ASSEMBLY
1. The first and last uprights in a row of shelving are End Uprights. The remaining uprights in a row are
Intermediate Uprights (see assembly graphic above). End and Intermediate Uprights are available in
welded assemblies or may be built. To build, lay the front and rear post parallel to each other on the floor or saw
horses. Position Angle Posts with the 1” flange pointing up. The front post may be Beaded or Angle. The back
post is always Angle.
Install Shelf Clips on both posts at the desired shelf locations by inserting the fingers of the clip into the
rectangular holes in the post and sliding down until the clip is fully seated. Install the clips for the bottom shelf in
the bottom two rectangular holes; install the clips for the top shelf in the top two rectangular holes.
The Upright Side Sheet is attached to the side of the Angle or Beaded post as shown using ¼- 20 x 5/8” Truss
Head screws and nuts. Upright Sheets are supplied with two screws and nuts for every foot of height. Note: Bolts
cannot be placed where shelves are located.
2. Intermediate Uprights are built like End Uprights, except Double Angle Posts replace Single Angle Posts (see
graphic above). Double Angle Posts are made by bolting two Single Angle Posts together with two ¼-20 x 5/8”
screws and nuts. Install shelf clips on both sides of the post assembly. The Upright Side Sheet is bolted to the
side of the Double Angle Posts with ¼-20 x 5/8” Truss Head screws and nuts.
If a Beaded Post is used, attach the Upright Side Sheet to the side of the Beaded Post with ¼-20 x 5/8” Truss Head screws and nuts.
3. Stand two End Uprights or an End and Intermediate Upright to build the first unit. Hold the uprights in position and install the top and bottom Shelves on to
the shelf clips. Make sure shelves are completely seated on the clips by tapping them down with a soft hammer. Repeat this process with the rest of the
shelves in the first unit.
4. While holding the unit vertical, install a Back Sheet using ¼-20 x 5/8” screws and nuts. Attach the Back Sheet to the inside of the rear angle posts as
shown. Slide one edge of the sheet between the shelf and post; then slide the other edge bowing the Back Sheet as needed. Line up the holes in the post
with holes in the back and bolt in place using ¼-20 x 5/8” Truss Head screws and nuts. Note: Bolts cannot be placed where shelves are located. Bolt
backs according to number of bolts and spacing shown below.
Height of Closed Back
Total Number of Bolts and Nuts
Maximum Bolt Spacing
To 3’ 11-1/2”
4
46-1/2”
4’1” to 5’11-1/2”
6
36”
6’1” to 7’11-1/2”
8
31-1/2”
8’1” to 9’-11-1/2”
10
30”
5. If building a row of shelving, continue to add units by standing additional uprights and installing shelves and backs. The last upright in a row is an end
upright.
6. Back to back (double) rows are built like single rows, except common backs are used. The common Back Sheet is installed on the inside of one of the
units, with the bolts going through both rear posts of the back to back units. This will securely tie the back to back units together.
Side Sheet
Beaded Post
(use at front only)
Intermediate
Upright
Shelf
Clip
Welded Upright Assemblies –top view
Intermediate-Beaded
End-Beaded
Intermediate-Angle
End-Angle
End Upright
(At row ends)
Angle
Post
Shelf
Clip
Intermediate
Upright
Beaded Post
(Used at front
only)
Side
Sheet
Back
Sheet

INDUSTRIAL CLIP SHELVING ASSEMBLY INSTRUCTIONS #7002376/ 2019
3743 Boettler Oaks Drive (Suite A) Uniontown OH 44685 ---- 800.477.1255 ---- www.republicstorage.com
SWAY BRACING PATTERNS –NOTE: Bracing patterns represent the minimum bracing required for units 8’-1” high and under in Seismic Zone 0.
Back and Side Bracing –Top
View
Side Bracing –Side View
Back Bracing –Front View
Indicates bay
reference in “Side
Bracing - Side
View” (right).
Indicates bay
reference in “Back
Bracing - Front
View” (below).
Indicates location of sway brace pair.
For more than 4 bays wide, repeat the 4 wide
pattern (i.e. Bay 5 the same as Bay 1, Bay 6 the
same as Bay 2, etc.).
Unit Detail for Back and Side Bracing –Top View
Back Panel or Sway Brace
Side-to-side units share common
upright sheet or sway braces.
Back-to-back units share common
back sheet or sway brace.

INDUSTRIAL CLIP SHELVING ASSEMBLY INSTRUCTIONS #7002376/ 2019
3743 Boettler Oaks Drive (Suite A) Uniontown OH 44685 ---- 800.477.1255 ---- www.republicstorage.com
SHELVING ACCESSORIES
Foot Plate –Angle and Beaded Post
Attach Angle Post with ¼-20 x 5/8” truss head
screw and nut. Attach Beaded Post with ¼-20 x
1” truss head screw and nut. Floor anchors are
not supplied with foot plates.
NOTE: When factory welded uprights are used,
field drill bottom hole of angle post for footplate.
Front Base - Angle Post
Attach to Angle Post with Tinnerman Nuts
#702517 and #10 x 5/16” truss head sheet metal
screws. Half Shelf Clips are furnished with 1-1/2”
bases.
Front Base –Beaded Post
Attach 1-1/2” base with #198743 base clips, ¼-20
x 1-1/2” truss head screws, nuts and #10 x ½” long
sheet metal screws. Attach 3” base with #198742
base clips, ¼-20 x 1” truss head screws, nuts and
#10 x ½” long sheet metal screws. Half shelf clips
are used with 1-1/2” front bases.
Universal Bin Front
Insert right and left hand clips into Beaded or
Angle Post directly above shelf. Bend locking tab
at bottom of clip into rectangle in post.
Locking Tab
End Base
Attach to posts with Tinnerman Nuts #702517
and #10 x 1/2” truss head sheet metal screws.
Shelf Divider
Attach to Series 2000 shelf with #701487 Plastic
Panel Clips. When installed, front edge of divider
is 5/8” back from front edge of shelf.
Angle Divider
Attach to Series 2000 shelf with #12-24 x 3/8”
truss head screws and nuts.
Sliding Divider
Divider has front return flange to maintain
alignment on shelf.
Shelf Box Guide
Attach to Angle Post with ¼-20 x 1” truss head
screws and nuts.
Label Holder
Attach to Series 2000 Shelf
With #701487 Panel Clips.
Half Shelf Clips
Panel
Clip