resi-linx RL-BV2100 User manual
resi-linx | Vcomm
®
WARRANTY
Vcomm Pty Ltd states that the warrant that the customer can rely on is that
provided by the manufacturer. In the event of any warranty claim please
contact us and we will forward it to the manufacturer. The manufacturer will
then determine the extent of their liability. This expressly negates, to the
extent possible by Australian law, any warranty reliance on Vcomm Pty Ltd.
RL-BV2100
AV Distribution Range
‘linx-AV’ 4 x 8 Component Video/Audio Matrix Switch
www.resi-linx.com
INSTALLATION MANUAL
A
B
D
C
EFG
H
I
12V DC
INPUT
IR REPEATERS
A1
1
2
IR SELECT
ABCDEFGH
A2 2-Y Pb/Cb Pr/Cr 4-Y Pb/Cb Pr/Cr
1-Y Pb/Cb Pr/Cr 3-Y Pb/Cb Pr/Cr
2
1
COMMON
RS232
A3 A4
SOURCE
B D F H B D F H
RL-BV2100
IR
OUTPUT
I
1
2
3
4
OUTPUT
II
A C E G A C E G
A B C D E F G H
OUTPUT
H
K
M
RL-BV260B
J
L
Cable Requirements
4 pair twisted cable
Hardware Connection
1. Ensure all power to equipment is switched off prior to
installation.
RL-BV2100
2. Connect Component Video Lead (red, green, blue)
from RCA Video output 1 A of Transmitter to the
Component terminals of AV Source.
3. Connect 3.5mm Audio Cable from Audio Terminals 1
B of Transmitter to the Analogue and/or Digital Audio
Terminals of the AV Source.
4. Repeat steps 2 - 3 for Source 2 - 4 inputs.
5. Connect RL-IR700/800* IR emitter to Common Output D
of Transmitter. Place the other end within 25mm of the IR
Receiver on the AV Source (depending on environmental
conditions).
6. For Discrete IR control, connect RL-IR700/800 IR Emitter
from Discrete Output 1 or 2 C and place emitter
head in front of IR Receiver of the desired device using
RL-ACC160* IR Emitter Shield. Choose which Discrete
IR source is to be controlled in each zone. Select via Dip
Switch E Discrete Emitter Output Port 1 or 2 and the
corresponding zone A, B etc.
7. Connect 2 x RJ45 sockets of Transmitter (OUTPUT IA
and OUTPUT IIA) to corresponding INPUT I and INPUT
II Receiver in zone A via 4 pair twisted cable. Repeat for
zones B - H. (eg. OUTPUT IB and II B to zone B INPUT I
and II)
8. Connect RS232 Cable F to control system.
RL-BV260B
9. Connect Component Video lead (red, green, blue) from
RCA Video output J of Receiver to the corresponding
RCA Video input on the Component Device (TV, etc).
10. Connect Analogue Audio Lead (green) from Analogue
Audio output M of Receiver to corresponding Audio
Input of the Component Device (TV, etc).
11. If required connect Digital Audio Lead (orange) from
Digital Audio Output K of Receiver to corresponding
Audio Input of the Component Device
12. Connect RL-BV500* IR Target to Input L of Receiver.
Flat Target can be easily mounted (either directly using
adhesive backing, or by using RL-ACC150* Target
Mount) to the desired location, anywhere within the line
of sight of remote controls.
13. Repeat steps 9 - 12 for connection of zones B - H.
14. Connect supplied 12V DC Switch Mode Power Pack to
Power Input G on Transmitter.
15. Once installation is complete, switch on power to all
equipment. Indicator LED’s will illuminate to show which
Source 1 - 4 is selected in each of the Zones A - H.
* Sold separately
B
A RCA Video Output
B Digital + AnalogueAudio
Input A1 - A4
C Discrete IR Emitter Outputs
D Common IR Emitter Outputs
E Discrete IR Select Switch
F RS232 Output
G 12V DC Power Input
H RJ45 Socket
I Indicator LED’s
J RCA Video Output
K RCA Digital Audio Output
L IR Target Input
M Analogue Audio Output
Transmitter
Receiver
Vcomm Pty Ltd
ABN: 99 091 281 524
N15275
®
WARRANTY
Vcomm Pty Ltd states that the warrant that the customer can rely on is that
provided by the manufacturer. In the event of any warranty claim please
contact us and we will forward it to the manufacturer. The manufacturer will
then determine the extent of their liability. This expressly negates, to the
extent possible by Australian law, any warranty reliance on Vcomm Pty Ltd.
RL-BV2100
AV Distribution Range
‘linx-AV’ 4 x 8 Component Video/Audio Matrix Switch
www.resi-linx.com
INSTALLATION MANUAL
RL-BV260B
Connection to zones B - H
as above
Remote
Control
RL-BV500
Zone A
RL-BV2100
RS232 to control system
Troubleshooting
IR LED Indicator on RL-BV2100 Transmitter illuminates
briey upon receipt of IR commands.
NOTE: Some brands of TV/Monitors can reduce the
range of the IR Receiver Head, which is outside the
scope of the warranty.
RL-BV2100
Power 12V DC 1.5A Switch Mode
Maximum video input 1.2V P-P
Return loss >15dB to 1,000 MHz
Common mode rejection >40dB @ 1,000 MHz
Maximum distance cable Up to 100m
Video Signal Component
Audio Signal Digital + Analogue
Conguration 4:8
IR capability Yes
Connections In/Out 4 sets - 3 x RCA
2 sets - 8 x RJ45
6 x IR Emitter
4 x Digital Stereo/Analogue Audio
Vcomm Pty Ltd
ABN: 99 091 281 524
N15275
RCA Digital Audio to
Input Local Amplier
resi-linx | Vcomm
®
WARRANTY
Vcomm Pty Ltd states that the warrant that the customer can rely on is that
provided by the manufacturer. In the event of any warranty claim please
contact us and we will forward it to the manufacturer. The manufacturer will
then determine the extent of their liability. This expressly negates, to the
extent possible by Australian law, any warranty reliance on Vcomm Pty Ltd.
RL-BV2100
AV Distribution Range
‘linx-AV’ 4 x 8 Component Video/Audio Matrix Switch
www.resi-linx.com
INSTALLATION MANUAL
Hyperterminal RS232 Set up
See below settings and properties for hyperterminal
communication.
Vcomm Pty Ltd
ABN: 99 091 281 524
N15275
Item command Function Description
1ON power on N/A
2OFF power off N/A
3Ax 1st output , A, setting set 1st output from input x, x=1,2,3,4
4Bx 2nd outpout , B, setting set 2nd output from input x, x=1,2,3,4
5 Cx 3rd outpout , C, setting set 3rd output from input x, x=1,2,3,4
6Dx 4th outpout , D, setting set 4th output from input x, x=1,2,3,4
7 Ex 5th outpout , E, setting set 5th output from input x, x=1,2,3,4
8 Fx 6th outpout , F, setting set 6th output from input x, x=1,2,3,4
9 Gx 7th outpout , G, setting set 7th output from input x, x=1,2,3,4
10 Hx 8th outpout , H, setting set 8th output from input x, x=1,2,3,4
11 LK lock on LOCK , all status can be changed by RS232 only
12 UK lock of, or unlock UNLOCK , all status can be changed by RS233 and remote control
13 RT reset reset , set all output come from 1st input
14 ST ask status request status information
resi-linx | Vcomm
Table of contents
