Ress FM7 Pro User manual

Manual
Monitor FM7 Pro
RESS
The Producer
Visual Inspection Sweep Instruments Measuring Instruments

Camera-Handset
Art.-no. 2520
1. Delivery contents
- Camera-Handset
- Charger
- SD-card
4 RESS
2. Safety Notes
- The video inspection system is not waterproof!
- The video inspection system is not for use in the medical field!
- Any kind of reparations on inside of the unit, must be carried out, exclusively by qualified staff!
(If required, contact the RESS-customer service)
- The connection and disconnection, the respective components of the system, must always
be carried out without power supply!
- The video inspection system must be switched off after it has been used!
- To clean the monitor and the housing, please use a damp, clean cloth to prevent
scratches! We recommend a microfibre cloth.
- Please avoid contact with water of any kind.
- Please avoid collisions at any time! (use strap)
- Do not use aggressive cleanser for cleaning!
- Do not use the inspection system near a strong magnetic field!
- Avoid temperatures above 40 degrees Celsius. Only accomplish an inspection if heating is
switched off!
- This product has a certificate of conformity according to the guidelines 2004/108/EG.

2 The SD card slot is at the top of the
monitor.
3. Start-up
1 7 inches monitor
2 SD card slot
3 12 pin connector for camera-system cable
4 Charging socket
5 Control keys
6 LCD voltage display
7 On/Off switch
8 Trimmer for basic position of
the Rotary-Ball-Camera
9 Joystick control
RESS 5
7
6
5
8
1
2
4
3
9

6 RESS
4. Start-up
To control the movable camera head, press the
control stick in the direction you wish. The camera
head will keep this position.
Also bring the knobs into position, so that the
camera head is at rest.
By using the on/off switch (5) the whole camera
system is put into use.
If your portable camera head made an indepen-
dently movement, without the control stick been
touched, then use the two trimmers to bring it into
basic position.
Connect the system cable to the jack on the handset, by
putting the two 12-pin ends gently together and then
tighten screws with the sleeve.
Connect the jack of the camera to the 12-pin connector on
the camera head. Please make sure that the groove guide
of the plug matches with the socket. Screw the plug with
the threaded screw tight. Please note, that the camera can
only be put into use, when all connections of the system
have been made and the basic-unit is switched on. If this
process was successful, all lights on the inside of the
camera, which are used for the illumination of the chimney,
will turn on.
Please note that the working temperature for the camera
cable should not fall below +5°C. There is a risk of cable

RESS 7
Further functions at page 8.
5. Working with the device
Never forget to turn the camera off (6) at the end of an inspection, to avoid
discharging the battery unnecessarily! Press the button for 3 seconds.
Advice:
2 Photo storage1 Video recording start/stop
3 System settings 4 Selection of
photo memory
5 Selection of
video memory
6 On/Off switch
7 LCD voltage display
Basic functions
Power supply
8 Charging socket
By using the on/off switch (5) the whole camera system is put into use. While the Carrying-Device is switched on,
the continuous current battery voltage (in volts) will show on the LCD-display (7). The display starts to blink at
approx. 11,5 (after approx. 2 hours) and show you, that the battery runs empty. You have approx. 45 minutes left,
befor the device goes off. This will happen at 10.5 V.
With button no.1 you start video recording. At the same time the sound will be recorded. Pressing the button
again stops the recording. To save pictures press no. 4. You can take a look at the recordings by pressing button
no.3 and for photos no. 5. (The sound can be heard only on a PC).
At a new purchase of the devices, the battery is pre-charged. The using time with a full charged battery is
approximately 300 minutes, depending on which camera head is connected. Over the charging socket the
Camera-Handset will be recharged. The delivery contents a charger. This will recharge the battery. Charging takes
round about 1 1/2 hours. The charger has an over-discharge-protection. It automatically switches off when the
battery is fully charged. If the device has not been used for a long time, it is necessary to check, if the battery
voltage has dropped. If this is the case, then reconnect with charger. A fully charged battery has approx. 14,3 V.
Connect the charger plug to the charging-socket. Then please connect with
a socket. The green light indicates, that the charger is on. If the light is red,
the battery is being charged. Charging is completed when the red light
switches off. The charger will switch off automatically, so an overcharging is
impossible.

8 RESS
5. Control buttons Basic functions
Other configuration of the control buttons
Button no. 1: Video recording
Button no. 2: Photo storage
Button no. 3: System settings
Button no. 4: Selection of photo memory
Button no. 5: Selection of video memory
Button no. 6: On/Off switch
After opening the photo memory (4)
Button no. 1: Scroll forward
Button no. 2: Delete (definitive delete press 2x)
Button no. 3: Backward
Button no. 4: Start / stop video
Button no. 5: Scroll backward
After opening the video memory (5)
Button no. 1: Scroll forward
Button no. 2: Delete (definitive delete press 2x)
Button no. 3: Start / stop video
Button no. 5: Scroll backward
12
34
56
After opening the system settings (4)
The active number of current setting is marked yellow.
Button no. 1: Counting up
Button no. 2: Next
Button no. 3: Exit menu
Button no. 4: Back
Button no. 5: Count down
DATE: Setting of date year/month/day
TIME: Setting of hour : minutes
REC MODE: Does not have to be changed. Can
stand on PICTURE or AVI.
REC TIME: Setting of running time: 5-300 sec.*
BRIGHTNESS: Setting of display
CONTAST: Setting of display
SATURATION: Setting of display
TIMEDISPLAY: Fade in/out the date/time
EXIT: Back to live image
Exit the menu, by pressing button no.3 or by selecting
EXIT in the menu and press no.1 or 5. It will switch
back to the live image automatically, if there is no
selection within 10 seconds.
*If you want to save longer video sequences, you must
press after 300 seconds the record button again, to
trigger further storage.

RESS 9
6. Memory card
7. Technical data
Overall dimension 260 x 150 x 40 (L / W / H)
Weight ca. 1500 g
Casing Synthetic material / Powder-coated aluminum
Monitor 7 inches LCD-TFT color screen 156 x 86 mm
Storage media 2 GB SD-card
1 photo 32 kb (720x576 pixel)
120 second video 42 MB
Power supply Lead acid battery 12 V/2,2 Ah
Voltage monitoring LCD-display
Operating time Approx.165 minutes (depending on the camera head that is being used)
Charging time ca. 1 1/2 hours
The SD-card slot is on the top of the Handset. The
delivery contents an SD-card, where photos and
movies are saved onto.
Insert the SD-card with the writing on top until you
hear a "click". Now the SD-card is locked and ready
to be used. To remove, please push the SD-card
until you hear a "click" again. The card will pop out
automatically. Now it can be connected to a reading
device (not supplied).
Please note that the monitor supports SD-cards of
1-8 GB.

RESS GmbH & Co. KG
Am Hasselbruch 28
D-32107 Bad Salzuflen
Germany
Tel. ++49 5208/91270
Fax ++49 5208/8030
inf[email protected]
www.ress.de
19.03.2018
RESS
The Producer
Visual Inspection Sweep Instruments Measuring Instruments