REVERSO-MANUFACTURING DVP-1000 N User manual

REVERSO-MANUFACTURING INC.
MANUFACTURERS OF
FIREPLACE EQUIPMENT AND ACCESSORIES
790 Rowntree Dairy Road, Woodbridge, Ontario, Canada L4L 5V3
Tel: [phone] Fax: [phone]
www.reversomfg.com Email: [email protected]
These appliances have been tested and found to comply with the
established standards for GAS-FIRED DIRECT VENT WALL
FURNACES in CANADA and the U. S. A.
CAN1-2.17-M91, ANSI-Z21.50(a)-1990 CAN/CGA2.22-
M86, WH-GPN-001 ANSI-Z21.44a-1992&CGA I.R.#41
INSTALLATION AND OPERATING
INSTRUCTIONS
REVERSO "BUILDERS CHOICE" DIRECT VENT FIREPLACES
DVP-1000 N (Natural Gas) DVP-1000 P
(Propane)
For Your Safety
Do not store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or any other appliance.
For Your Safety
If you smell gas:
1. Open windows.
2. Don't touch electrical switches.
3. Extinguish any open flame.
4. Immediately call your gas supplier.
WARNING: Improper installation, adjustment, alteration, service or maintenance can cause
injury or property damage. Refer to this manual. For assistance or for additional information,
consult a qualified installer, service agency or gas utility.
PLEASE KEEP THESE OPERATING INSTRUCTIONS FOR FUTURE REFERENCE
Rev. September 2005
fire-parts.com

2
IMPORTANT: SAVE THESE INSTRUCTIONS
To the new owner.
We at REVERSO MFG. LTD. are pleased that you have chosen one of our products for your
home environment. We would like to take this opportunity to assure you that you have chosen
a top quality product which will provide you with all the warmth and charm of a wood
fireplace at the flick of a switch without any of the fuss and mess you would normally
associate with lighting a wood fire.
You can now enjoy many years of clean burning, trouble free operation, as well as, high
efficiency performance.
At REVERSO - we -have continued to deliver on our commitment to uncompromising quality
and time proven reliability. We stand proudly behind our entire wood and gas burning
products division,-which are industry renowned by the brand name REVERSO "BUILDERS
CHOICE"
'The REVERSO "BUILDERS CHOICE" DVP-1000 N/P models have heavy gauge fireboxes,
state of the art safety controls, and.Teak proof construction, all in an aesthetically pleasing
finished package. When setup correctly, the gas effects flames of realistic glowing. logs offer
what many people consider to be the most realistic simulated wood fire available today. Some
of the logs even include burn out effects and knot holes which ;appear to have burned through
and allow flames to lick out.
The logs employed in these units are manufactured with the latest space age ceramic fiber
material which products the glowing effects commonly associated with a wood fire but, can
be used over and over again for many years without showing any signs of wear.
All "REVERSO" products have been tested by Warnock Hersey to the national standards of
the Canadian and American Gas Associations for both safety and efficiency.
The DVP-1000 direct vent gas fireplaces are also the most versatile fireplaces available today,
as they are approved for either top or rear venting, suiting sidewall or rooftop applications.
Since they arrive completely finished, inside and outside, the Units- can be installed as either
freestanding / non-recessed or as recessed (with optional zero clearance kit).
Please take a moment now to acquaint yourself with these instructions and the many features
of your new "REVERSO" gas fireplace.
fire-parts.com

3
GENERAL INFORMATION
All "REVERSO" gas-fired appliances -must be installed in accordance with these
instructions.. Carefully read all of the instructions in this manual first. Consult the building
authority having jurisdiction to determine the need for a permit prior to commencing the
installation.
NOTE: Failure to follow these instructions could cause a malfunction of the fireplace which
could result in death, serious bodily injury, and/or property damage. Failure to follow these
instructions may also void your fire insurance and/or warranty.
FOR YOUR SAFETY
Follow these instructions, local codes and information in CAN / CGA B149 (.1 or .2)
Installation Codes for Gas Burning Appliances and Equipment ('m Canada) or (in the
U.S.A.) follow local codes and/or the most current edition of the National Fuel Gas Code
ANSI Z223.1.2
FOR SAFE INSTALLATION AND OPERATION OF YOUR 'REVERSO" GAS
FIREPLACE, PLEASE CAREFULLY READ THE FOLLOWING INFORMATION:
PREPARATION FOR INSTALLATION
Remove the - packaging from the appliance, and check to make sure there is no damage. In
the event damage is found, please report it to both the carrier and your dealer as soon as
possible.
Before beginning, carefully check the glass door and the log set. Check to make sure there is
no hidden damage to the logs or any other component of the appliance.
INSTALLATION INSTRUCTIONS
GENERAL
This appliance should be inspected annually, at least, by a professional service person. It is
important that control compartments, circulating air passages and other components be kept
clean and free from excessive lint from carpeting. Make sure the pilot is turned off before
attempting to service this appliance.
It is a good practice to have all of your gas appliances inspected annually.
Due to high temperatures, the appliance should be located out of high traffic areas and away
from furniture and draperies.
Children and adults should be alerted to hazards of high surface temperatures and should
stay away to avoid burns or clothing ignition.
Young children should be carefully supervised when they are in the same room as the
fire-parts.com

4
appliance.
Clothing or other flammable material should not be placed on or near the appliance.
Always connect this gas fireplace to an approved vent system and vent to the outside of the
building envelope. Never vent to another room or inside a building.
Make sure that the vent is properly sized and is of adequate height to provide the proper
draft.
Inspect the venting system annually for blockage and any signs of deterioration.
To prevent injury do not allow anyone who is unfamiliar with the operation to use the
fireplace.
A faint odor and slight smoking will likely be noticed when the fireplace is first used. Open
a window until the slight smoking stops.
Any glass removed for servicing must be replaced prior to operating the appliance.
Thoroughly clean the location that has been chosen for installation of the REVERSO
fireplace.
Ensure that it is level before securing to the floor and connecting the gas.
Take a minute to plan out the best routes for the gas lines and the venting system.
Move the appliance into the exact location where it is going to be installed.
Under no circumstances should this appliance be modified.
Parts that have to be removed for servicing must be replaced prior to operating this
appliance. Only parts supplied by REVERSO should be used in this appliance.
Never use solid fuels such as wood, paper, cardboard, coal, etc., in this appliance.
Always keep the area around these appliances clear of combustible materials, gasoline or
other flammable vapors and liquids. These appliances should not be used as a drying rack
for clothing or for hanging Christmas stockings or decorations.
SPECIFICATIONS: FOR REVERSO GAS PRODUCTS
GAS -FIRED VENTED WALL FURNACES (CAN/USA) DVP-1000 N/P
(ALL MODELS ARE SUITABLE FOR INSTALLATION AS FREESTANDING NON-
fire-parts.com

5
RECESSED FIREPLACES, FOR INSTALLATION IN BEDROOMS OR FOR ZERO
CLEARANCE INSTALLATION WITH THE OPTIONAL ZERO CLEARANCE KIT)
SPECIFICATIONS
The above models have all been.certified for use with either Natural or Propane gases,
designated in the model number by the suffix N (Natural Gas) or P (Propane).
Both of these appliances draw all of their air for combustion from the outside of the
dwelling through specially designed vent pipe, which maybe vented through the sidewall of
the dwelling or vertically through the roof.
All models are equipped with a variable input gas control which allow reductions in input of
approximately 25%, when heating requirements are lower.
FOR INSTALLATIONS ABOVE SEA LEVEL
In Canada, these appliances are certified for altitudes of 0 - 2000' and must bee derated by
15% for installation at elevations between 2000 and 4500'. In the U.S.A., the appliance must
be derated 6% for every 1000' above 2000' elevations.
ALTITUDE (In feet): (0-2000' ) (2000'-4500')
NATURAL PROPANE
N
ATURAL PROPANE
ORIFICE SIZES:
(REAR OR TOP VENT) #50DMS #56DMS #52DMS #60DMS
Manifold Press:("W.C.) 3.5" 10.0"
Min. Manifold Press: 2.1" 7.8"
Max. Supply Press: 7.0" 13.0"
Min. Supply Press: 4.5" 10.8"
Max. BTUH Input: 15,000 15,000 12,500 12,500
Mm. BTUH Input: 12,500 12,500 10,000 10,000
STEADY STATE EFFICIENCY:
Rear Vent ( 8” Min. vent) Top vent ( 35’ Max. vent)
FAN OFF (MIN. VENT L): 69.1 %
FAN ON (MAX. VENT L): 71.3 % 74.5% 73.4% 73.3% — 76.4% —
AFUE/DOE
(
Pilot OFF when a
pp
liance not in use
)
:
N
atural Gas Pro
p
ane
Blower OFF 65.0% 67.3%
Blower ON 80.9% 82.4%
fire-parts.com

6
DIMENSIONS
Front Width: 34"
Height: 36"
Depth: 12" Shipping Weight: 98 lbs.
CLEARANCES TO COMBUSTIBLES: Sides: 2"
(FRAMING MATERIAL) Rear: 0"
Top: 2"
Floor: 0"
Corner Installation: As above, with 2” clearance to corner of appliance.
ALWAYS OBSERVE THE APPROVED CLEARANCE TO COMBUSTIBLE MATERIALS.
ELECTRICAL REQUIREMENTS
No external power is required to operate the REVERSO "BUILDERS
CHOICE" DVP-1000's if these models have the optional Millivolt gas control
which uses the pilot flame to generate enough electricity to operate the main
burner whenever the manual switch provided is on.
DVP-1000 N/P models may also have a fan delay limit switch mounted in the control
compartment of the appliance. This switch is designed to delay the operation of the fan until
sufficient heat has built up, to avoid uncomfortable drafts and to hold the fan on for several
minutes after the burners have shut-off extracting all of the usable heat.
When supplied with the optional circulating fan, the appliance does come fully equipped with
a 120 volt household plug which will supply electrical power for the air circulation fan.
When connected to 120 volts, the appliance must be grounded in accordance with local codes,
with the current version of CSA C22.1 (in Canada) or the National Electrical Code
ANSI/NFPA70.
Circulation fan: 120V / 60 hz - Variable speed fan.
NOTE: Operation of the fan increases the efficiency and the heat output of the appliance.
LOCATIONS
As noted earlier, these appliances are approved for bedroom installations.
They may be installed on any flat, hard surface combustible or otherwise. They can be located
within the allowable clearances to combustibles against the wall, in a corner or out in the
center of the room if desired. (See diagram #1)
fire-parts.com

7
Don't forget to try to line up the center point of the flue with an open joist space above the unit,
when planning to vent vertically.
fire-parts.com

8
GAS LINE CONNECTION
WARNING: Only persons licensed to work with gas piping may make the necessary gas
connections to this appliance.
The appliance is provided with an opening on both
sides of the control compartment. A 3/8" gas supply
pipe must be brought near this inlet hole, from either
the left or right hand side. It is recommended that a
union be provided inside or close to the control
compartment to facilitate easier servicing..
NOTE: The gas line connection may be made using
3/8" copper tubing or an approved flex connector.
Since some municipalities have additional local codes,
it is always best to consult your local authorities and
the CAN/CGA-B149 (1 or 2) Installation Code.
For U.S.A. gas installations follow either local codes or the current edition of the National
Fuel Gas Code ANZI.Z223.1
GAS PIPE TESTING
The appliance and its shutoff valves must be disconnected from the gas supply piping system
during any pressure testing where the pressure exceeds 1/2 PSIG (3.45 kpa).
Always check for gas leaks with a soap and water solution, after completing the required
pressure test.
NEVER USE AN OPEN FLAME FOR GAS LEAK TESTING
When using copper or flex connectors use only fittings approved for gas connections. The gas
control inlet is 3/8" NPT, therefore the 1/2" rigid gas line must be reduced to 3/8" NPT. A
typical gas line installation layout for rigid pipe is shown on the previous page.
VENTING (COAXIAL 6" AIR INTAKE & 4" EXHAUST)
Kits are available for venting either through the sidewall or vertically through the roof.
SIDEWALL VENTING (REAR VENT - ANGLED DUCT)
MAX. RUNMIN. RISE
24" 2"
26" 3"
28" 4"
30" 5"
fire-parts.com

9
FOLLOW THE VENTING INSTRUCTIONS ON THE FOLLOWING PAGES
PRECISELY BEFORE BEGINNING THE INSTALLATION, TAKING CARE TO
ENSURE AN APPROPRIATE OUTSIDE LOCATION FOR THE VENT TERMINATION
CAN BE ACCOMMODATED.
ALSO, TAKE CARE TO REVIEW THE DIAGRAM ON THE FOLLOWING PAGE
WHICH OUTLINES LOCATION LIMITATIONS GOVERNED BY NATIONAL CODE.
Since the Direct Vent is an unpressurized system, it will be sensitive to local conditions such
as elevation, wind conditions, vent location and fuel type utilized. This will affect the overall
appearance of the gas flame.
fire-parts.com

10
Termination Locations
A = Clearance above grade, veranda, porch, deck, or balcony
[*12 inches (30mm) minimum]
B = Clearance to window or door that may be opened
[*12 Inches (30 cm) minimum]
C = Clearance to permanently closed window [minimum 12 Inches (30 cm)
recommended to prevent condensation on window]
D = Vertical clearance to ventilated soffit located above the terminal within a
horizontal distance of 2 feet (60 cm) from the centre -line of the
Terminal [18 Inches (46 cm) minimum]
E = Clearance to unventilated soffit [12 Inches (30 cm) minimum]
F = Clearance to outside corner [12 Inches minimum]
G = Clearance to inside corner [12 inches minimum]
H = * Not to be Installed above a meter/regulator assembly within 3 feet (90
cm) horizontally from the centre line of the regulator
I = Clearance to service regulator vent outlet [* 6 feet (1.8 m) Minimum]
J = Clearance to non-mechanical air supply inlet to building or the
combustion air inlet to any other appliance [12 Inches (30 cm)
minimum]
K = Clearance to a mechanical air supply Inlet [* 6 feet (1.8 m) minimum]
L = ***Clearance above paved side-walk or paved driveway located on
public property [* 7 feet (2.1 m) minimum]
M = Clearance under veranda, porch, deck, or balcony [*12 Inches (30 cm)
minimum **]
*** A vent shall not terminate directly above a side-walk or paved driveway which is located between two single family dwellings and serves both dwellings *
** Only permitted if veranda, porch, deck, or balcony is fully open on a minimum of 2 sides beneath the floor *
* As specified in CGA B149 installation Codes (1991) Note: local Codes or Regulations may require different clearances
fire-parts.com

11
CAUTION: USE ONLY
COMPONENTS SUPPLIED BY
REVERSO FOR VENTING
INSTALLATION
fire-parts.com

12
fire-parts.com

13
fire-parts.com

14
fire-parts.com

15
INSTALLATION OF LOG SET (Standard Set)
Log Set Four pc. (4) - Two top (cross logs)
- Two bottom Ceramic Fiber logs
The log set for DVP 1000 is shipped in the master carton. Check to ensure there is no damage
to any of the four (4) logs. It is very important to install these logs in their proper position to
insure safe operating conditions. (SEE THE FOLLOWING LOG PLACEMENT DIAGRAM)
WARNING:: Dangerous operating conditions may occur if these logs are not positioned in
their certified locations.
1. Open the front door. Note the "easy-open" latches. Make sure to lower the door slowly so
it does not hit the floor abruptly.
2. Remove logs from their packing.
3. Place rear fiber log on rear log holder.
4.. Place front fiber log on front log holds
5. Place the two cross logs on the positioning notches provided and according to the diagram
shown above.
CARE OF YOUR DOOR ASSEMBLY
It will be necessary to clean the glass periodically. During a cold start up condensation will
sometimes, form on the glass, this is a normal condition with all gas fireplaces and stoves.
However, sometimes this condensation can allow dust and lint to cling to the glass surface.
Also, sometimes initial paint curing of the appliance can leave behind a slight film on the
glass. This is a temporary problem.
It is therefore recommended that the glass be cleaned initially after about the first two weeks
of use.
After that, depending upon the amount of use, cleaning should be required no more than two
fire-parts.com

16
or three times per season. To clean the door, use a mild cleaner (i.e.. Windex, Fantastic) and a
soft cloth. Abrasive cleaners will damage the protective coating.
ROUTINE MAINTENANCE
WARNING:
Improper installation, adjustment, alteration, servicing or maintenance can result in personal
injury and property damage. Always refer to this manual for normal maintenance
requirements. For further assistance or additional information consult a qualified gas installer,
your REVERSO MFG. dealer or your local gas supplier.
This appliance must, not be operated if it or the gas controls have been under water. Contact a
qualified gas technician for service before attempting to operate.
This appliance should be serviced regularly, to ensure continuing safety and efficiency
contact a qualified technician at least annually.
For cleaning, turn the gas. control knob to the "OFF" position. This will extinguish the pilot
flame. Wait at least five (5) minutes before cleaning.
NOTE: This appliance is equipped with Neo Ceram Glass which can only be broken by a
significant impact or misuse.
FOR CLEANING THE INSIDE OF THE FIREBOX
Remove the logs carefully from the combustion chamber and vacuum the burner compartment
thoroughly. Vacuum any dust on the logs and remove any lint from the main burner and pilot
burner.
After carefully replacing the logs in their correct positions and resealing the door, relight the
pilot following the instructions on the attached label, and turn on the main burner.
1. Check to ensure that all burner ports are lit and burning properly.
2. Check to ensure that the right branch of the pilot flame is engulfing the thermocouple tip,
while the left branch of the pilot flame is engulfing the thermopile and the other branch is
long enough to light the rear main burner.
3. Check to ensure that the main burner lights instantly when the on switch is turned on and
that the flame carries across to the front burner fairly evenly.
fire-parts.com

17
REVERSO DV 200 OPTIONS
1. Fireflick remote control kit.
2. Wall thermostat.
3. GOLD door kit.
4. GOLD trim kit.
5. Variable speed fan.
6. Zero clearance kit.
7. Optional fifth log.
8. Roof or Sidewall vent terminal.
9. Propane or Natural gas controls.
REPLACEMENT PARTS LIST
1. PILOT ASSEMBLY
2. PIEZO IGINTOR
3. MANIFOLD ASSEMBLY
4. FRONT BURNER
5. MAIN BURNER
6. FRONT LOG
7. REAR LOG
8. RIGHT HAND LOG
9. LEFT HAND LOG
10. FRONT BURNER ORIFICE
11. MALE PIPE ELBOW 900
12. MAIN BURNER ORIFICE
13. GAS VALVE
14. BLOWER ASSEMBLY
15. DOOR GLASS
16. VARIABLE SPEED CONTROL
○
14
○
13
fire-parts.com

18
fire-parts.com

19
fire-parts.com

20
fire-parts.com