3) Setting the high temperature protective setting
The default setting is 50ºC and we recommend this is set at 40ºC. Press the menu key once.
This will start the menu characters toflash e.g. F0. Use the “+” or “-“ keys to adjust to F2.
Now press the ON/OFF key and the temperature will flash. Press the “+” or “-“ key to adjust
the temperature to 40ºC.
Press the ON/OFF key again to accept the setting and finally press the Menu key to return to
the main screen.
4) Setting the four comfort levels - TIME & TEMPERATURE
The enclosed S430 instruction sheet shows the default factory settings for each comfort lev el.
25ºC when you require heat for comfort and 10ºC when you are out of the building or in bed.
The thermostat does not turn off during each 24 hour day, so when you require the most
economical operation e.g when the building is not occupied or you are in bed, or a higher level
when you actually need heat, the temperature setting can be adjusted to any levelyou want.
Comfort level settings are ONLY made in the AUTO setting mode. To change between
AUTO and MANUAL setting press on the “-“ key for up to 20 seconds. Press the ON/OFFkey
to accept. In AUTO setting the time period symbol will appear on the screen e.g. P1, P2, P3 or
P4.
Examples
Comfort Level No. 1 - Wake - P1
Comfort Level No. 2 - Leave - P2
Comfort Level No. 3 - Return - P3
Comfort Level No. 4 - Sleep - P4
To make changes press the Menu key and the menu characters will f lash. Adjust to menu F1
with the “+” or “-“ keys. Press the ON/OFF key to accept and the days of the week flash e.g 1 2
3 4 5.
Press the ON/OFF key and the time period P1 will flash. Press the ON/OFF key to accept and
the time will flash. Press the “+” or “-“ key to adjust the time. This is the time you want the
heating to operate in the morning. Press the ON/OFF key to accept and the temperature will
flash. Press the “+” or “-“ key to adjust the temperatureto say 25ºC. Press the ON/OFF key to
accept and the next time period will flash e.g. P2.
Press the ON/OFF key to accept and the time will flash. This is the time you want to leaveyour
property. Press the “+” or “-“ key to adjust the time. Press the ON/OFF key to accept and the
temperature will flash. This setting can be as low asyou want, say 10ºC. Repeat the above for
all time periods and end by pressing the ON/OFF key then press the menu key to returnto the
main screen
5) Manual Setting
This allows you to over-ride the temperature setting in any period level at any time. For
example,you arrive home early and want the heat on. Manual changes can only be made in
the MANUAL setting. To change between AUTO and MANUAL setting press on the “-“ key for
up to 20 seconds. Press the ON/OFF key to accept.
Assumeyou have set the temperature for this Level at 15ºC and the room temperature reading
to the right of the screen is 18ºC. The heating will not be energised in this setting.
Press the “+” or “-“ key to adjust the temperature. The temperature will start to flash when you
press the key. Use the “+” or “-“ keyto set a new temperature above 18ºC, as in this example.
Lets say 22ºC, and then press the ON/OFF key and the thermostat will re-set and the heating
symbol will appear at the top of the screen. The thermostat will automatically return to your
original time period settings when it reaches the next comfort level (time period) setting.
To check thefloor temperature in Mode 0 press the ON/OFF key.
Eltrace Limited, Unit 14, The Sidings Business Park, Whalley, Lancashire, BB7 9SE
Tel: 01254 825 234 Fax: 01254 825 212 email: sales@eltrace.co.uk
