RHINO NG2005 Installation instructions

RHINO®Grind
Nut Butter Grinder
Model No. NG2000, NG2004
& NG2005
Installation &
Operating Manual
THIS DOCUMENT CONTAINS
IMPORTANT INFORMATION
AND MUST BE READ AND
UNDERSTOOD PRIOR
TO INSTALLATION AND
OPERATION OF NUT
GRINDER EQUIPMENT.
Revision Date: 20200819:0426
Revision: H

Access to Help
VIDEOS AND THIS MANUAL ARE ONLINE
We recommend reading every page of this paper RHINO® Grind manual, but us-
ingaQRcodescanneronyoursmartphonewilltakeyou toanelectronic webpagewith
videos, and electronic manual. Where you see this logo in this paper manual, you can
scan to go to a video on the topic being discussed. This QR code and information can
also be found on the RHINO® Grind when you need information.
If you do not have a QR code scanner, you can simply open a web browser, and type
www.rhinogrinder.com/help to access the information.
PLEASE NOTE: Viewing these videos instead of reading the manual does not
relieve you of any responsibility for knowing the information contained herein.

The products, technical information, and instructions contained in this manual are subject to change without
notice. These instructions are not intended to cover all details or variations of the equipment, nor to provide
for every possible contingency in the installation, operation or maintenance of this equipment. This manual
assumes that the person(s) working on the equipment have been trained and are skilled in working with
electrical, plumbing, pneumatic, and mechanical equipment. It is assumed that appropriate safety precautions
are taken and that all local safety and construction requirements are being met, in addition to the information
contained in this manual.
This Product is warranted only as provided in Trade Fixtures’ Commercial Warranty applicable to this Product
and is subject to all of the restrictions and limitations contained in the Commercial Warranty. Trade Fixtures
will not be responsible for any repair, replacement or other service required by or loss or damage resulting
from any of the following occurrences, including but not limited to, (1) other than normal and proper use and
normal service conditions with respect to the Product, (2) improper voltage, (3) inadequate wiring, (4) abuse,
(5) accident, (6) alteration, (7) misuse, (8) neglect, (9) unauthorized repair or the failure to utilize suitably
qualied and trained persons to perform service and/or repair of the Product, (10) improper cleaning, (11)
failure to follow installation, operating, cleaning or maintenance instructions, (12) use of “non-authorized”
parts (i.e., parts that are not 100% compatible with the Product) which use voids the entire warranty, (13)
Product parts in contact with water or the product dispensed which are adversely impacted by changes in
liquid scale or chemical composition.
Contact Information:
To inquire about current revisions of this and other documentation or
for assistance with any Trade Fixtures product contact:
www.tradextures.com
800-872-3490
Trademarks and Copyrights:
This document contains proprietary information and it may not be reproduced in any way without permission
from Cornelius/Trade Fixtures.
This document contains the original instructions for the unit described.
TRADE FIXTURES, LLC.
1501 Westpark Drive, Suite 5
Little Rock, AR Tel: [phone]
Correct Disposal of this Product
RECYCLE
This marking indicates that this product should not be disposed with other household wastes throughout the
EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle
it responsibly to promote the sustainable reuse of material resources. To return your used device, please use
the return and collection systems or contact the retailer where the product was purchased. They can take this
product for environmental safe recycling.
Printed in U.S.A.

TABLE OF CONTENTS
Table of Contents
Page
Introduction / How to Use
Safety Precautions 6
Specications / Features 10
Getting Started / Quick Start 13
Unpackaging and Installation 13
Product Listing 14
Cleaning and Sanitizing 15
Recommended Cleaning Schedule 16
Disassembly/Reassembly Procedure 17
Cleaning of Product Delivery Parts 19
Wiring Schematic 20
Illustrated Parts List 22
Troubleshooting 23
Setting the Timer Switch 30
Setting the Grind Texture (Smooth or Coarse) 31
Warranty Information 33
IMPORTANT: THIS MANUAL IS A GUIDE FOR INSTALLING,
OPERATING, AND MAINTAINING THIS EQUIPMENT. REFER TO
TABLE OF CONTENTS FOR PAGE LOCATION OF DETAILED
INFORMATION PERTAINING TO QUESTIONS THAT ARISE DURING
INSTALLATION, OPERATION, SERVICE AND MAINTENANCE, OR
TROUBLESHOOTING THIS EQUIPMENT.
SHOULD YOUR RHINO® Grind NUT BUTTER GRINDER EVER
LOSE POWER, WE SUGGEST LOOKING AT BOTH THE
POWER ON/OFF SWITCH AND FAQ’S IN THIS MANUAL
TO TROUBLESHOOT BEFORE CONTACTING US.

INTRODUCTION
The RHINO® Grind nut butter
grinder is a free standing machine
thattakesnutmeat,and grindsit into
a coarse or ne spreadable paste for
consumption by customers at retail.
Our RHINO® Grind nut butter
grinder will be referred to within this
OPERATING MANUAL as the
RHINO, or RHINO® Grind. The
useoftermssuch asunit, machine,or
equipment are meant to be synony-
mous with the RHINO® Grind or its
components.
Installation of the RHINO® Grind
nut butter grinder must be on a at
surface, away from heat, and near a
properly grounded, electrical
receptacle for its safe operation.
HOW TO USE/SELL
Customers using the RHINO®
Grind nut butter grinder will
select a container or cup to dispense nut butter into for purchase.
This process begins when the customer places the container or cup below the
dispensingspout,andpressesthestart/stopbuttonwhichwillactivatethemotorand
grindingplates. Thisactiongrindsthenutmeatintoaspreadablepasteknownasnut
butter. Oncethemachinehasdeliveredthedesiredamountofproduct,theconsumer
willreleasethestart/stopbuttonwhichwilldeactivatethemotorcausingthegrinding
plates and dispensing to stop.
Our RHINO® Grind nut butter grinder will dispense nut butter paste at a ow rate of
2.5Lbs/min. of peanuts. Dierent nut meat ow rates, and how to adjust
settings can be found in this manual. Also, the RHINO® Grind nut butter
grinder ships in the Fine texture setting, with instructions on how to change found
within this manual if needed based on nut meat being ground.
Thank you for your interest in nut butter grinding, and your purchase of the
TRADE FIXTURES RHINO® Grind!

SAFETY PRECAUTIONS
SAFETY WARNING SIGNS
Read and Follow All Instructions
Read and follow all safety instructions, best practices, and precautions in this
manual and on the RHINO® Grind nut butter grinder (decals and labels).
Retain this manual for future reference.
Read and follow all applicable safety regulations before operating the RHINO®
Grind.
Indicates that a danger of death
or serious injury exists.
Indicates that a risk of electrical shock exists. Only trained, licensed
professionals should operate in areas where this warning exists.
Representssomethingyoumust NOT do.
Representssomethingyoumustfollow.
Represents a ground is needed to prevent electrical shock.
Itisrecommendedthatthisactionbehandledbyaserviceperson.
SIGNS USED IN MANUAL AND ON FIXTURE
Please follow these warning signs to prevent injury to users and other persons.
Disconnect Power to the Unit before Servicing or Cleaning.
Usealockout/tagoutproceduretoensuresafety.Verifypowerisototheunitbefore
any work or cleaning is performed.
Do not plug several appliances into the same receptacle.
This could cause overheating and the risk of re.
Make sure the power plug is not squashed, pinched, frayed or damaged and
do not bend the power cord excessively or place heavy articles on it.
Adamagedpowerplugmayoverheatandcauseare.Ifthepowercordisdamaged,
have it replaced immediately.
Do not insert the power plug with wet hands, or if cord/plug is wet.
You may receive an electric shock doing so.
Indicates that a risk of personal
injuryormaterialdamageexists.
6

SAFETY PRECAUTIONS
Do not grind anything other than specied nut meat through this unit.
See a list of approved nut meats found on pages 8-9 of this manual.
Do not plug the RHINO® Grind in a power socket and/or circuit breaker
with Ground Fault Circuit Interrupt (GFCI).
If you connect the power cord with GFCI socket and/or GFCI circuit breaker
rated 6mA or less, the GFCI will fault/trip. CAUTION - The RHINO® Grind
will only work with an industrial Type ‘B’, GFCI rated 30mA or more.
Do not disconnect the power cord by yanking on it.
Damagetothecordmaycauseashort-circuit,reand/orelectricalshock.Ifthepower
cordisdamaged,itmustbereplacedbythemanufacturer,itsserviceagent,orsimilarly
qualied persons immediately in order to avoid a hazard.
Do not disassemble or repair the electrical components of this unit yourself.
You run the risk of causing a re, malfunctions and/or personal injury.
The equipment must be grounded.
Youmustgroundtheunittopreventanypowerleakageorelectricalshockcausedby
currentleakage.Improperuseofthegroundplugcanresultinariskofelectricshock.
Ifitisnecessarytouseanextensioncord,useonlya3-wireextensioncordthathasa
3-bladeroundpluganda3-slotreceptaclethatwillaccepttheplugontheequipment.
ThemarkedratingoftheextensioncordshouldbeAC100V120V,16Aormore.Ifa
grounding adapter is used, make sure the receptacle box is fully grounded.
Service warranty section
Anychangesormodicationsperformedbya3rdpartyonanishedproductisnot
covered under Trade Fixtures warranty service.
Safety caution section
TradeFixturesdoesnotrecommend3rdpartymodication;therefore,TradeFixtures
is not responsible for safety issues that result from 3rd party modications.
Safety Tips
Carefullyreadallsafetymessagesinthismanualandsafetysignsonequipment.Keep
safetysignsingoodconditionandreplacemissingordamagedsafetysigns.Learnhow
to operate the equipment and how to use the controls properly.
Theunitmustbeserviceandmaintainedbyappropriatelytrainedpersonnel.Keep
your RHINO® Grind in proper operating condition.
Do not allow unauthorized modications to the equipment.
Donotletchildrenorinrmpersonsoperatetheequipmentwithoutadultsupervision.
7

SAFETY PRECAUTIONS
SafetyPrecautions
ItisrecommendedthatyoudoNOTgrindtwoconsecutivetimeswithouta30secondrest,or
you run the risk of overheating the RHINO®Grind.
Technicians
CAUTION - Only trained and certied electrical personnel should service this
equipment. ALL WIRING MUST CONFORM TO NATIONAL AND LOCAL
CODES.
Shipping and Storage
CAUTION - RHINO® Grind nut butter grinder must remain upright to avoid
damage, or injury. Always ship, carry, store, and handle the RHINO® Grind nut
buttergrinderinanuprightpositiontopreventimproperinstallationand/ortipover.
Proper Lifting Procedures
When placing the RHINO® Grind for the rst time, you will be required to lift and
setapproximately70+lbsatthelocationofyourchoosing. Theinitialll,andsubsequent
refills of the nut hopper will weigh 20lbs. Wherepossible,werecommendusingateam
approach (2x).
Alwaysusegoodposture(keepingyourbackstraightandbendingyourknees,notyour
back)tolift. NEVERstandonastepstool,orladderandreachbeyondyourarmslength
toplacetherelledhopper backontotheRHINO®Grindnutbutter grinderbody.
NEVERletthehopperdrop intoplace. Itmustbesetgentlytoavoiddamagetothe
RHINO® Grind nut butter grinder body.
STOPPING THE RHINO®Grind
INTERRUPTING/SHUTTING OFF POWER
In the event of motor malfunction, electrical outage, surge, or
any other unusual situation where you want to immediately
shut o power to the RHINO® Grind:
1) Locate Main On/O power switch and move to the OFF position.
2) Remove the power cord from the main socket at the wall.
RESUMING NORMAL OPERATION
Oncetheissuehasbeenremovedandcorrected,thepowerisreadytoberestored:
1) Plug power cord into the main socket.
2) Switch the Main On/O power switch to the ON position.
3) Press the activation (start/stop) button on green illumination till the grinder
start dispensing the butter.
8
NOTE:The RHINO®Grind is not designed for a wash-down environment and
MUST NOT be placed in an area where a water jet could be used.

ANTI TIP SAFETY BRACKET
The RHINO® Grind should be operated on a sturdy level countertop, table or sur-
face capable of supporting 100lbs per completely full unit. If the RHINO® Grind
is installed on a short pull out drawer that does not fully support to the front of the
cup rest, we highly recommend using an anti-tip bracket. The anti-tip bracket can
be mounted by using Philips head wood screws or machine screws and nuts (Fig 1).
Once the anti-tip bracket is mounted, slide the RHINO® Grind into place and onto
the anti-tip device which will secure the unit in place (Fig-2). For additional anti-tip
bracket use recommendation, please contact Trade Fixtures.
9
Fig. 2
Slide back against Anti-Tip device
secure anti-tip
device to a level,
sturdy wooden
countertop using
wood screws ...
... or any other
worksurface (steel,
metal, or non-wood)
using machine screws,
nuts, and washers
for a secure,
snug installation Slideout Drawer
Fig. 1
SAFETY PRECAUTIONS

This section gives the unit design data and electronic safety feature of the
RHINO® Grind nut butter grinder.
DESIGN DATA & ELECTRICAL REQUIREMENTS
RHINO® Grind nut butter grinder Style (Model #):
621058631 - Nut Butter Grinder-Stainless Steel (NG2000) 100-120V/50-60Hz, 16A
621058738 - Nut Butter Grinder-Stainless Steel (NG2004) 200-240V/50-60Hz, 7.5A
621058697 - Nut Butter Grinder-Rest of World (NG2005) 200-240V/50-60Hz, 7.5A
European model (NG2001) 230V/50Hz
Ambient Operating Temperature 60°F / 15.6C to 72°F / 22.2C
Note: Nut Butter is best dispensed from a 72° ambient room temperature.
We recommend a 20A dedicated circuit and breaker with standard 3 prong
ground per RHINO® Grind machine. Typical current draw is 7A.
DIMENSIONS OF RHINO®Grind
The minimum counter depth is 15 1/2” to support the RHINO® front and rear feet.
Ifthe counterdepth islessthan22”we highlyrecommendusingtheanti-tipbracketwith
the unit.
General Description
LABEL
activation (start/stop) button
dispensing
spout
Nut
Hopper
Main On/O power switch
32oz deli
cups t
under
spout!
SPECS AND FEATURES
10

A.
B.
C.
A.
B.
Reverse Detail of Hopper
Hopper
MOTOR INTERRUPTING SAFETY SWITCHES
The RHINO® Grind is equipped with 2 safety
switches to prevent injury during rell or cleaning.
1.) When the hopper or 2.) the front merchandiser
has been removed for cleaning, or is not properly
installed, the power
to the RHINO®
Grind’s motor is
interrupted. IT
DOES NOT
MEAN THAT
POWER TO THE
MACHINE IS ABSENT.
PLEASE PROCEED
WITH CAUTION!
A. Align the 4 tabs in the back of the hopper with the rear of
the RHINO® Grind. B. Tabs should rest in the slots
on the grinder body. C. Align front merchandiser ensuring
the tabs align with no gap. Assure front merchandiser
fully seats to chassis.
The RHINO®
Grind should start
when the start/stop button
is pushed. If the button
is ashing red/yellow, check
for proper installation / alignment
at locations shown in A., B. and C.
and review Troubleshooting section.
REMOVING THE HOPPER, OR FRONT MERCHANDISER
This shows how to remove and reinstall the hopper, or front merchandiser for
cleaning, maintenance, etc.
REMOVAL
The hopper simply
rotates up until you can
lift it straight up from
the RHINO®
Grind chassis.
The merchandiser
may require a rm pull
toreleasefrommagnets.
HOPPER
MERCH.
HOPPER
MERCH.
REINSTALL
Align 4 tabs of
the hopper at the
rear, and rotate
it back into
position. The
merchandiser ts
into two slots and
rotates upward on chassis.
CHASSIS CHASSIS
11

SPECS AND FEATURES
12
LABEL GOES HERE.
PRODUCT LABEL
There is a product label holder
on the front of the RHINO®
Grind which measures 6” wide
by 4” tall. The visible area
measures 5.5” by 3.75” tall. Slide
the product label behind the
clear sheet and into the channel.
We also have a 6”
wide by 4” tall generic label that
we can send you, or you can
make your own.
POWER CORD MANAGEMENT
How to attach the cord to the cabinet for easy sliding in and out.
View from behind View from the front
Attach power cord through the wire clamp attached to the
back of your nut grinder. Allow enough slack to plug the
cordintothegrinder.
Extend grinder slideoutfullythenusewireclamp
(provided)toclampcord to back as shown. Makesurecord
is taut per detail. This will ensure the cord does not get
caughtbehindgrinderslideoutwhenpushedbackinplace.
Thread power cord through grommet hole and plug in.

UNPACKAGING AND INSTALLATION
Remove RHINO® Grind from packaging, and inspect for any damage that may
haveoccuredinshipping. Ifyouobserveranydamage,emailusimmediatelyatservice@
tradextures.com, otherwise install the Anti Tip device for attaching securely to a at
shelf, then level the RHINO® Grind and slide onto the anti-tip device with a minimum
clearance of 1/4” on each side, 2” at the rear and 5” minimum at the top of the unit. Lo-
cate the power socket and plug the RHINO® Grind into a grounded
receptacle. Do not plug several appliances into the same receptacle. Each RHINO®
Grind should be on a dedicated circuit, based on the design data.
LOAD NUT HOPPER
Lift the lid on hopper and ll with nut meat. Replace lid.
PRIMING THE RHINO GRIND
The RHINO® Grind was lubricated, sealed, and test run at our plant. No
further maintenance is required other than regular, cleaning of the unit. (For more
information, see cleaning/sanitizing section of this manual).
PRODUCT LISTING
DO NOT GRIND ANY NUTS WHICH ARE STILL IN THEIR SHELL.
Dryroastednutsworkbestforproducingaspreadablebutter. Raw,unroastednuts
or those with low oil content are not recommended to grind in the RHINO® Grind, as
theymayproduceathick,coarsenutbutter mealpaste ornotproducenutbutteratall.
Almonds, specically, need to be dry-roasted with a very low moisture content.
Products like sesame or ax seeds, or any not listed below are not grindable or don’t
produce favorable results when attempted.
The following nuts are great choices for selling as nut butter:
Peanuts, honey roasted peanuts, almonds, cashews, pecans, macadamia nuts,
hazelnuts, walnut pieces, pistachios, roasted sunower seeds, pumpkin seeds, or any
addition of chocolate pieces (which should be limited to 25% of hopper volume). The
RHINO® Grind was developed to grind whole nut and pieces, do not hesitate to grind
up whole nuts. Due to the all natural, no preservative nature of freshly ground nut but-
ters, we recommend refrigerating product after it is ground. Refer to Page 9.
Some nut grades will pose diculties, while other grades of the same nut type
will not. If you are having diculty with processing specic grades of nuts,
please contact service for assistance. We cannot guarantee every nut grade
processing performance but have had positive results (see chart next page).
Getting Started/Quick Start
UNPACKING/SETUP
13

Type of Nut/Seed Whole Halves Chopped/Pieces
Almonds - Whole (Dry Roasted)
Peanuts (Dry Roasted)
Honey Roasted Peanuts
Almonds - Diced (Dry Roasted)
Cashews** (Dry Roasted)
Filberts/Hazelnuts (Dry Roasted)
Pecans
Walnuts
Macadamia Nuts (Dry Roasted)
*- Diced 12/8 will not work as they are too fine.
** - Any grade between BB and SW210 should work.
NOTES:
Do NOT grind any nuts which are still in their shell.
Dry roasted nuts work best for producing a spreadable butter. Raw, unroasted nuts or those with low oil content are not
recommended to grind in the Rhino Grind unit, as they may product a thick coarse nut butter meal paste or not produce nut
butter at all. Some customers have found removing the duckbill to grind raw nuts is best.
Almonds, specifically, need to be dry-roasted with a very low moisture content. Products like sesame or flax seeds, or any not
listed above are not grindable or don't produce favorable results when attempted.
The Rhino Grind unit was developed to grind whole nuts and pieces,
do not hesitate to grind up whole nuts!
Great choices for selling as Nut Butter
Oil roasted nuts can be ground on the 'coarse' setting with the duckbill installed for a very smooth nut butter result.
Chocolate and Butterscotch Chips can be added, but should be limited to 25% of the total volume and no larger than a 10mm
size.
*
Getting Started/Quick Start
UNPACKING/SETUP
14

Cleaning and Sanitizing Procedures
PLEASE NOTE:
Before your rst use, or after the cleaning/sanitizing/drying
process, you will need to run a cup of nuts through the grinding
process until a sellable buttery nut paste begins to grind. Running the
RHINO® Grind on Fine texture minimizes the nut powder/dust dispense you
may see, or particles until the paste forms. Discard this cup, and you are now
ready to sell fresh nut butter!
FOREWORD ON CLEANING
These cleaning procedures are based on the rules and regulations of the U.S.
Food and Drug Administration’s (FDA) Food Code (latest edition, 2013), and
the Arkansas Department of Health, Food Protection Services division. The
Food Code is a model for safeguarding public health and ensuring food is
unadulterated and honestly presented when oered to the consumer. It
represents the FDA’s best advice for a uniform system of provisions that
addressesthesafetyandprotectionoffoodoeredatretailandinfoodservice.
This model is oered for adoption by local, state, and federal governmental
jurisdictions for administration by the various departments, agencies, bureaus,
divisions, and other units within each jurisdiction that have been delegated
compliance responsibilities for food service, retail food stores, or food vending
operations. Alternativesthatoeranequivalentlevelofpublichealthprotection
toensurethatfoodatretailandfoodserviceissafearerecognizedinthismodel.
These instructions are to be considered the best case for ensuring a perfectly
clean RHINO® Grind nut butter grinder. Any deviation from these
instructions inwhole,orinpart,wouldbeatyourdiscretionwhichcouldlessen
yourretailingexperience. Ifyouareunsure,pleasecheckwithyourlocalorstate
Health Department (Food Safety Division).
NSF CERTIFICATION
Trade Fixtures / New Leaf Designs has received NSF Certication.
NSF for sanitation and food safety (NSF-8)
UL CERTIFICATION
Trade Fixtures / New Leaf Designs has received UL (Underwriters
Laboratory) Certication. UL for electrical and ammability
safety (UL 763 and CAN/CSA C22.2 No. 195)
15
CLEANING/SANITIZING

RECOMMENDED CLEANING SCHEDULE
DAILY CLEANING
• To assure the RHINO® Grind maximizes sales and attracts customers, it is
important to maintain a clean area.
•Onadailybasis,theexteriorofthecabinetshouldbewipeddown toremoveany
foodtrace,cleananyspillagewhichmayhaveaccumulated,andremoveanytrash.
• Occasionally throughout the day, the use of warm water and disposable towel
is suggested to clean the dispensing nozzle by removing food deposits.
(Disassembly of the dispensing spout from the machine is not necessary) Also
cleaning the food contact catch tray.
WEEKLY CLEANING
• The RHINO® Grind is easily cleaned by hand. Avoid using commercial
dishwashers, or detergents which may deteriorate grinder componentry.
• Keeping the RHINO® Grind clean will ensure many years of operation, build
consumer condence, and oer a fresh, healthy option for customers.
• Weekly cleaning is more involved than daily cleaning and involves disassembly
of the main grinder mechanism, which is easily done by hand. The following
components will be addressed in weekly cleaning ... Auger, Grinding Plates,
Cover, Housing, Duckbill Valve, Nut Hopper, internal components and Shutter.
Please see the “Cleaning of Product Delivery Parts” section of the manual.
FOOD CONTACT CLEANING (INTERIOR COMPONENTS)
The following pages provide detailed instruction on how to clean the RHINO®
Grind’s internal components. Instructions are provided in this manual for
cleaning.
WE RECOMMEND YOU USE THESE INSTRUCTIONS TO CLEAN THE
NUT BUTTER GRINDER EVERY TIME YOU REPLACE OR REFILL THE
NUT HOPPER. CAREFULLY READ AND FOLLOW ALL INSTRUCTIONS.
Catch tray can
be removed, and
cleaned by pulling
out and away from
RHINO®Grind
chassis.
CLEANING/SANITIZING
16

Remove hopper
from equipment
Pull to remove
front merchandiser
Unscrew the locking
captive screw on top
Rotate Cover clockwise to unlock
Pull out once aligned with slots.
Disassembly / Reassembly
SAFETY PRECAUTION FOR UNIT CLEANING
1. Switch o the RHINO® Grind at Main On/O power switch.
2. Disconnect the power cord from the power source.
3. Remove, or dispose of the nut hopper contents depending on their age.
4. Disassemble as per instructions given below.
For any issues you may encounter with the RHINO® Grind nut
butter grinder, we recommend you take the following course of action:
- Review this instruction manual
- Check the Electronic Stop / Power Supply
- Call us at 1-800-872-3490, or email service@tradextures.com
The use of this supplied wrench may be required to break
loose the grinding wheel in the next step. Press and hold augur lock
pin and turn the wrench counter clockwise. PLEASE NOTE: Do
not use this tool to tighten the grinding wheel during reassembly.
WE RECOMMEND YOU HAND WASH ALL
COMPONENTS AND AVOID USING DISHWASHERS OR
DETERGENTS WHICH MAY DEGRADE THE PARTS.
1.
Push pin
upward
2. Turn wrench
counterclockwise
17
CLEANING/SANITIZING

Press/Hold Auger lock pin. Rotate
Grinding Wheel counterclockwise.
Remove thumbscrews from
housing. Place on catch tray brkt.
Remove housing from
the auger assembly
Wipe the auger, rotary seal
and housing mounting plate
thoroughly using a dry cloth
Empty the hopper bin &
remove the shutter by pulling the
cotter rings and clevis pins
Wipe thoroughly internal and
external surfaces of the hopper,
shutter and pins using a dry cloth
Disassembly / Reassembly
Unscrew 3 captive screws, and seperate the
retaining ring from cover for cleaning. When
reinstalling these pieces, make sure the raised
weld nuts do not rest against the cover when
hand tightening the retaining ring and 3 thumb
screws. Failure to do so, may result in leaking.
Unscrew the two thumb screws which hold
the grinding plate on the auger housing
and remove for cleaning. Take notice of
the alignment notch which needs to be
located in the range as shown by the red
circle during the reinstallation process.
Alignment
Notch
CAUTION: THE GRINDING PLATE MAY HAVE SHARP BURRS,
EDGES OR TEETH. PROCEED WITH CAUTION AND CARE.
Retaining ring
only installs
one way
Raised
weld
lip up
CLEANING/SANITIZING
18

CLEANING OF PRODUCT DELIVERY PARTS
1. Remove Grinding Housing Cover, and pull the duck bill valve out.
2. Soak the parts in warm water for several minutes, then brush or otherwise
remove nut butter from all parts.
3. Brush wash all components with soapy water. Rinse thoroughly in clean,
warm water.
4. In a clean sink, prepare a sanitizing solution of KAY-5® Sanitizer/Cleaner,
or comparable sanitizer/cleaner by dissolving 1 packet in 2½ gallons (9.5
liters) of lukewarm water. Immerse the part for 1–2 minutes. Remove and
drain. DO NOT RINSE. Visually inspect ALL parts and surfaces are free
of residue, nut butter paste, particles, soaps, etc. If not, repeat steps 1-4.
5. Air dry all parts thoroughly & make certain that surfaces are free of
moisture. Reassemble the parts to the unit.
6. After reassembling, reconnect cord to power source & test the unit by
running it briey before adding nuts into the hopper.
A pictorial view of cleaning with a brush:
REASSEMBLY
1. Reassemblebyreversingtheinstructions.2.Ensurethenuthopperisproperly
installed. 3. Fillthenuthopperwith nutmeat.4. Connectcord topowersource.
5. Switch on the RHINO® Grind. 6. If activation button does not activate,
please refer to page 18 Troubleshooting. 19
CLEANING/SANITIZING

Wiring Schematic / U.S. Model
20
100-120V
50-60Hz