Richcomm NetmateLite User instructions

Richcomm System Technologies Co.,Ltd
Tel:[phone]
Fax: [phone]
www.richcomm.com.cn/e
1
NetmateLite
Basic Web-based SNMPCard for UPS
Installation and Setting
Instruction

Richcomm System Technologies Co.,Ltd
Tel:[phone]
Fax: [phone]
www.richcomm.com.cn/e
2
Hello
Installation Requirement
The monitored UPS with RS232 communication port or internal slot;
The computer(best administrators computer) with Ethernet port
A complete network environment.
Note: Please read this user manual before installation.

Richcomm System Technologies Co.,Ltd
Tel:[phone]
Fax: [phone]
www.richcomm.com.cn/e
3
1. Ports Definition
NetmateLite/NetmateLite Mini/NetmateLite SE Available
①Ethernet Port: UTP 10/100M RJ45 Ethernet port.
②USB Port: For initial configuration;
③S1 (Green): Running indicator, flash is normal;
④S2 (Green): SNMP running indicator, flash is normal, flash frequency is determined by
SNMP inquire cycle;
⑤S3 (Red): Device status indicator (red), continuous on shows connected well with UPS and
have communication, flash shows device disconnected or communication failed;
⑥Default: Factory default switch;
⑦RS232 Port(External card): Connect with UPS;

Richcomm System Technologies Co.,Ltd
Tel:[phone]
Fax: [phone]
www.richcomm.com.cn/e
4
⑧Gold Finger: Insert in UPS internal slot;
NetmateLite Mini1/NetmateLite Mini2 Available
①Ethernet Port: UTP 10/100M RJ45 Ethernet port.
②PW (Red): Power status indicator, often light shows device power is connected, no light
means not connect power.
③S1 (Green): Running indicator, slow flash normal;
④S2 (Green): SNMP running indicator, flash normal, flash frequency is determined by
SNMP inquire cycle;
⑤S3 (Red): Device status indicator (red), continuous on shows connected well with UPS and
have communication, flash shows device disconnected or communication failed;
⑥4 Pin Serial Port: Connect with UPS;
⑦Gold Finger: Insert in UPS internal slot;

Richcomm System Technologies Co.,Ltd
Tel:[phone]
Fax: [phone]
www.richcomm.com.cn/e
5
2. Installation
2.1 Network Dirgram

Richcomm System Technologies Co.,Ltd
Tel:[phone]
Fax: [phone]
www.richcomm.com.cn/e
6
2.2 Hardware Installation
External SNMP Cards
Procedure:
①Use DB9 pin cable connect external card with UPS by RS232 port
②Use T568B network cable connect to network
③Use power adapter connect to power supply(12V DC)
Internal SNMP Cards
Procedure:
①Insert internal SNMP card to solt
②Use T568B network cable connect to network
To Network
To Power

Richcomm System Technologies Co.,Ltd
Tel:[phone]
Fax: [phone]
www.richcomm.com.cn/e
7
2.3 Set Network Segment
For initial configuration, we should set a same network segment before login in web interface, the
default IP address of SNMP cards are: 192.168.0.100, so network segment should be set like
192.168.0.XXX

Richcomm System Technologies Co.,Ltd
Tel:[phone]
Fax: [phone]
www.richcomm.com.cn/e
8
2.4 Command “ping”
Before we input input the user name and password, we can check the dault IP address whether
available in your network by command “ping”
Ping Pass
Ping Fail

Richcomm System Technologies Co.,Ltd
Tel:[phone]
Fax: [phone]
www.richcomm.com.cn/e
9
2.5Login Web Monitoring Interface
All above steps finished, open a web browser(suggest IE/firefox/chrome etc), input default IP
address 192.168.0.100 and enter
Input user name and password , default user name & Password are both “admin”.
（Users can change the User name and Password by the post setting）

Richcomm System Technologies Co.,Ltd
Tel:[phone]
Fax: [phone]
www.richcomm.com.cn/e
10
2.6Web Monitoring Interface
After input the user name and password, the monitoring homepage will come out soon, and then we
can check the UPS current status and do other software setting
3. Software Setting Introdution
3.1 UPS Information
Sub-Menu：
System Information
Device Information
Current Status
Remote Control
3.1.1 System Information
This page is to display UPS basic information and network information. The info shown here are
provided by NetmateLite SNMP card itself and parameter settings