RIGHT ANGLE 200CPU User manual

FOR THE HEIGHT, WIDTH, & DEPTH OF YOUR CPU. MAKE SURE THE CPU HAS
PAGE 1 OF 3
ENOUGH CLEARANCE TO ROTATE LEFT & RIGHT AS FAR AS YOU WANT IT TO
1
VERSION DATED: 8/15/11
ROTATE.
STEP 2: REMOVE THE CPU HOLDER FROM THE TRACK
SQUARE
2
TAPE MEASURE
#2 SQUARE HEAD DRIVER BIT
#2 PHILLIPS DRIVER BIT OR
CORDLESS DRILL
TOOLS REQUIRED FOR ASSEMBLY:
READ ALL THE INSTRUCTIONS BEFORE BEGINNING
BY SLIDING IT OUT
TOWARD THE FRONT AND SET IT ASIDE.
STEP 3:
HARDWARE PACK 50519
E POSE THE GLUE DOTS ON THE TOP OF THE TRACK 1 BY PULLING
THE PAPER STRIPS OFF THE TRACK. POSITION THE TRACK IN THE LOCATION
SHOWN AND PRESS IT FIRMLY IN PLACE SO THE GLUE DOTS WILL HOLD THE
TRACK TO THE BOTTOM OF THE WORKSURFACE.
IMPORTANT NOTE: THE WORKSURFACE MATERIAL MUST BE COMPATIBLE WITH
THE SCREWS PROVIDED. THE WORKSURFACE MUST BE AT LEAST 1" THICK.
INSTRUCTION 50576
STEP 4: ATTACH THE TRACK 1
. DO NOT OVER-TIGHTEN THE SCREWS. USE A LOW TORQUE
TO THE WORKSURFACE WITH (4) WOOD
SCREWS
SETTING ON THE DRILL.
200CPU HOLDER INSTALLATION INSTRUCTIONS:
STEP 1: DETERMINE THE LOCATION TO MOUNT THE CPU HOLDER ALLOWING
ITEM # PART # DESCRIPTION QTY.
1 50093 16" TRACK ASSY 1
2 51708 M5 x 18mm SQ/PH/WSHR HEAD WOOD SCREW 4
3 200CPU ECONOMY CPU HOLDER 1
4 52679 8-32 x 3/8 PHILLIPS TRUSS HEAD MACHINE SCREW 2
5 50330 #20/3 WIRE PULL HANDLE 1
6 50232 FRONT STOP 1
7 50200 10-24 x 1/2 SELF TAPPING MACHINE SCREW 2
6703 ZINSER ST., SCHOFIELD, WI 54476
PHONE: [phone] FAX: [phone]
.raproducts.com
K&A MANUFACTURING
1
PAPER STRIPS
COVERING
GLUE DOTS
STEP 3
WORKSURFACE AND BACK 3/8"
WITH THE FRONT OF THE
1
2
PLACE THE TRACK SQUARE
BOTTOM OF WORKSURFACE
STEP 4

PAGE 2 OF 3
STEP 5: ATTACH THE HANDLE 5 TO THE FRONT OF THE 200CPU HOLDER 3
USING (2) MACHINE SCREWS 4 FROM THE BACK.
NOTE: IF YOUR CPU IS LESS THAN 3 7/8" WIDE, SKIP FORWARD TO STEPS A-C
ON PAGE 3 OF 3.
STEP 6: PLACE THE CPU HOLDER 3 ON TOP OF YOUR CPU AND WRAP THE
STRAPS AROUND THE BOTTOM OF THE CPU. CONNECT THE ENDS OF THE
STRAPS TOGETHER. TIGHTEN THE CPU IN THE CPU HOLDER BY PULLING ON
THE FREE ENDS OF THE STRAPS.
STEP 7: SLIDE THE CPU HOLDER 3 & THE CPU INTO THE TRACK.
STEP 8: INSERT THE FRONT STOP 6 INTO THE END OF THE TRACK. ATTACH
IT USING (2) SELF TAPPING SCREWS 7 FROM THE BOTTOM UP AND INTO
THE TRACK.
6703 ZINSER ST., SCHOFIELD, WI 54476
PHONE: [phone] FAX: [phone]
.raproducts.com
K&A MANUFACTURING
4
STEP 5
THAN 3 7/8" WIDE, SEE
PAGE 3 OF 3.
VERSION DATED 8/15/11
3
NOTE: IF YOUR CPU IS LESS
5
STEP 6
PULL ON THE FREE ENDS OF STRAPS
TO TIGHTEN THE CPU ONTO THE HOLDER.
6
STEPS 7 & 8
7

PAGE 3 OF 3
IF YOUR CPU IS LESS THAN 3 7/8" WIDE FOLLOW THE STEPS BELOW:
STEP A: REMOVE THE BUCKLES FROM THE FREE ENDS OF THE STRAPS ON THE CPU HOLDER,
THEN REMOVE THE STRAPS FROM THE CPU HOLDER.
STEP B: RE-ROUTE THE FREE ENDS OF THE STRAPS THROUGH THE SLOTS IN THE TOP OF THE
CPU HOLDER AS SHOWN ON THE FRONT VIEW. RUN THE FREE ENDS UP THROUGH THE RIGHT
HAND SLOTS FROM THE BOTTOM. THEN RUN THE FREE ENDS BACK DOWN THROUGH THE
LEFT HAND SLOTS FROM THE TOP.
STEP C: RE-ATTACH THE BUCKLES TO THE STRAPS. THE BACK OF THE BUCKLES MUST FACE
THE CPU. RUN THE FREE ENDS OF THE STRAPS INTO THE BUCKLES FROM THE BACK. THEN
RUN THE FREE ENDS BACK THROUGH THE BUCKLES OVER THE TOPS OF THE LOCKING BARS.
THE FREE ENDS MUST FACE OUT FROM THE CPU HOLDER. GO BACK AND COMPLETE STEPS 6-8.
VERSION DATED 8/15/11
6703 ZINSER ST., SCHOFIELD, WI 54476
PHONE: [phone] FAX: [phone]
.raproducts.com
K&A MANUFACTURING
FRONT VIEW
FREE ENDS
ROUTE THE FREE ENDS UP THROUGH THE
RIGHT HAND SLOTS, THEN DOWN
THROUGH THE LEFT HAND SLOTS.
RUN THE FREE ENDS UP THROUGH THE BUCKLES
FROM THE BACKS. THEN RUN THEM BACK
DOWN OVER THE TOPS OF THE LOCKING
BARS & THROUGH THE BUCKLES. THE FREE
ENDS SHOULD FACE OUT FROM THE CPU
HOLDER.
FREE END