Vivo STAND-V003D User manual

Triple Monitor Vertical Desk Stand
Scan the QR code with your mobile device or follow the link
for helpful videos and specications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v003d
[email protected]om www.vivo-us.com 1-800-371-5654
SKU: STAND-V003D

2 3
ASSEMBLY STEPS
PACKAGE CONTENTS
WARNING!
A (x1)
Pole
B(x1)
Base
C(x1)
Arm
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualied technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specied in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: NOT ALL HARDWARE INCLUDED WILL BE USED
D(x3)
VESA Plate
E(x3)
M4x6
F (x3)
M5x14
G (x1)
M10 Bolt
H (x1)
Support Plate
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
K (x1)
Grommet
Base
L (x3)
Wire Clip
OPTION A: Weighted Base Installation
1. Install the Pole (A) to the Weighted Base (B)
using M5x14 Bolts (F), and tighten using the
Allen Wrench (M), see Figure 1.
2. Optionally, you can drill a 10mm diameter hole
in your desk and secure using the Support
Plate (H), M10 Washer (I), Spring Washer (J)
and M10 Bolt (G). Fasten the M10 Bolt with
provided Wrench (N), see Figure 2.
I(x1)
M10 Washer
J(x1)
Spring Washer
STEP 1
M (x1)
Allen Wrench
N(x1)
Wrench
O(x12)
M4x12 Thumb
Bolt
P (x12)
M4x30
Q(x12)
M4 Spacer
OPTION B: Existing Grommet Hole
Installation
If the existing grommet hole comes with a
plastic protector, remove it to ensure a at
surface before installing the desk mount.
1. Install the Grommet Base Plate (K) to
the Pole (A) M5x14 Bolts (F), and tighten
using the Allen Wrench (M), see Figure 3.
2. Attach So Pad (r) to the Grommet Base
Plate (k), see Figure 4.
3. Position the Pole (A) on the mounting
surface and secure using the Support
Plate (H), M10 Washer (I), Spring Washer
(J) and M10 Bolt (G). Fasten the M10 Bolt
using provided Wrench (N), see Figure 5.
22 lbs
Per Arm
(10 kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
TOOLS NEEDED
Phillips
Screwdriver Drill
R(x1)
So Pad
h
g
i
l
j
Figure 2
a
f
b
Figure 1
h
g
i
j
a
k
f
Figure 3
Figure 5
rFigure 4

4 5
STEP 1 (Continued)
OPTION C: Self-Drilled Grommet Hole
Installation
1. Position the Pole (A) on the mounting
surface and mark the center hole. Drill
a 3/8” (10mm) diameter hole at the
marked position through the mounting
surface.
2. Install the Grommet Base (K) to the Pole
(A) using M5x14 Bolts (F), and tighten
using the Allen Key (M), see Figure 7.
3. Position the Pole (A) on the mounting
surface and secure using the Support
Plate (H), M10 Washer (I), Spring Washer
(J) and M10 Bolt (G). Fasten the M10
Bolt using provided Wrench (N),see
Figure 8.
STEP 3
OPTION A: Flat Back Monitor
For monitors with at backs attach VESA plate (D) using M4x12 Thumb Bolts (O).
OPTION B: Curved Back Monitor
For monitors with curved or recessed backs attach VESA plate using M4x30 Bolts (P) and M4 Spacers
(Q).
STEP 2
Install Monitor Arm (C) to the Pole (A). Fasten the bolt with supplied Allen Wrench (M). Attach the Wire
Clip (L) to the Pole (A).
h
g
i
j
k
a
f
Figure 6
Figure 8
rFigure 7
c
m
l
o
q
p

6 7
STEP 4 STEP 5
Fasten the grub screw in Monitor Arm to x the tilting angle by provided Allen Key (M). Manage the
wires as in the diagram.
Slide the monitor onto the head of Monitor Arm (C) as shown in the diagram. Install the M4x6 Bolt (E).
Make sure the bolt is installed before you rotate the monitor.
grub
scre w
e

Last Updated: 11/29/2018
If any parts are received damaged or defective, please contact us. We are happy to
replace parts to ensure you have a fully functioning product.
For more VIVO products, check out our website at:
www.vivo-us.com.
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected]om www.vivo-us.com 1-800-371-5654