Rightline Gear 110M10 User manual

1-Lay the air mattress over a at area, free from rocks
and sticks (Fig 1). Make sure the mattress is completely
unfolded and its ocked side is facing up (Fig 2).
3-Insert the air pump’s charge plug into the vehicle’s 12
volt DC outlet (Fig 4).
4-Place the adaptor into the mattress’s easy inate valve’s
opening (Fig 5). The adaptor will push the valve open.
Power the air pump on (Fig 6).
Fig 1 Fig 2
5-Inate the mattress to the desired rmness, turn the air
pump off, and remove the adaptor from the opening. The
air pressure inside the mattress will push the valve closed.
Screw the cap over the easy inate valve’s opening (Fig
7).
Inate The Air Mattress
2-Attach the large adaptor to the ination port on the side
of the air pump (Fig 3).
Fig 3 Fig 4
Fig 7 Fig 8
Fig 9
7-Place the mattress between the wheel wells of the truck
bed (Fig 9) with its ocked side facing up and its valve
side facing the rear of the truck.
6-Use the mouth valve to inate the mattress if the air
pump is unavailable (Fig 8).
Truck Bed Air Mattress 110M10, 110M60
www.rightlinegear.com/setup.html
Set Up
Video:
QR
CODE
WARNING: THE AIR PUMP’S POWER SUPPLY MUST
BE A VEHICLE’S 12 VOLT DC OUTLET.
Flocked
Side
WARNING: DO NOT LEAVE THE PUMP UNATTENDED
WHILE OPERATING. DO NOT ALLOW THE PUMP TO
GET WET OR KEEP IT RUNNING FOR OVER 15 MIN-
UTES. DO NOT OBSTRUCT THE INFLATION AND DE-
FLATION PORTS. DO NOT ALLOW SMALL DEBRIS TO
BE SUCKED INTO THE INFLATION OR DEFLATION
PORTS.
Fig 5 Fig 6
NOTE: IT IS RECOMMENDED TO KEEP THE MATTRESS
INFLATED FOR SEVERAL HOURS BEFORE INITIAL
USE. THE MATTRESS’S MATERIAL WILL STRETCH DUR-
ING THIS TIME AND ADDITIONAL AIR WILL BE RE-
QUIRED TO RETURN THE MATTRESS TO ITS DESIRED
FIRMNESS. THE LOSS OF AIR BEFORE INITIAL USE IS
NORMAL AND DOES NOT MEAN THE MATTRESS IS
LEAKING.
8-Store your gear between the mattress and the bed walls
(Fig 10).
Fig 10

WARNING: INFANTS AND YOUNG CHILDREN
CAN SUFFOCATE ON INFLATABLE MATTRESSES;
NEVER PLACE THEM TO SLEEP ON THIS AIR
MATTRESS. KEEP FLOCKED SIDE FACING UP.
KEEP SHARP OBJECTS AWAY FROM MATTRESS.
KEEP MATTRESS AWAY FROM FIRE. MATTRESS
NOT FOR USE IN WATER. MATTRESS NOT FOR
USE WHEN VEHICLE IS MOVING.
Fold The Air Mattress
1-Fold the sides of the mattress into the middle (Fig 15).
Fold side A over side B (Fig 16).
2-Roll the mattress toward the valve end to push out any
remaining air. Make sure to depress the easy inate
valve to let the air escape (Fig 17). Screw the cap over
the easy inate valve’s opening to prevent air from re-
entering.
3-Place the mattress and the air pump into the stuff sack
(Fig 18).
Fig 18
Fig 15 Fig 16
1 Year Manufacturer’s Limited Warranty
www.rightlinegear.com/product-warranty.html
Fig 17
Easy Inate
Valve
AB
Fig 13 Fig 14
4-Deate the mattress until no air remains inside.
Fig 11 Fig 12
1-Attach the large adaptor to the deation port on the
top of the air pump (Fig 11).
Deate The Air Mattress
2-Insert the air pump’s charge plug into the vehicle’s 12
volt DC outlet (Fig 12).
3-Place the adaptor into the mattress’s easy inate valve’s
opening (Fig 12) and power the air pump on (Fig 13).