Riley Hopkins RileyFLASH 16x16 User manual

RILEY FLASH 16X16 & 18X18
Assembly Instructions

2
Tools Required:
What’s in the box
• (x1) 7/16” Wrench • (x1) 9/16” wrench
Tag Item Q.
1Main flash panel assembly 1
2ZINC ATTACHMENT BRACKETS (RH & LH) 2
3LOWER STAND LEGS 4
4Hardware Kit 1
5UPPER STAND UPRIGHT POLE 1
6LOWER STAND UPRIGHT POLE 1
1
2
456
3

3
Tag Item Description Q.
11 PRHD-HC3/8NC2-1/4GR5ZC 3/8-16 x 2-1/4 Hex Cap Screw
Grade 5 Zinc 4
MFSA-RHFLASH-KIT
Riley Hopkins 16x16 & 18x18 flash dryer hardware kit
Tag Item Description Q.
1MFCO-CSTR2X3/8ML Caster, Medium Duty 2" Wheel
3/8" Stud 4
2MFCO-HANDLEVER Hand Lever knob tapered 3" long 1
3PRHD-CALR1INPIPE 1-3/8" id Locking Collar 1
4PRCO-KNBFLT3/8NC1-1/4ML Fluted bracket 3/8-16 x 1-1/4"
Male Stud 1
5PRHD-FLN3/8NCGR5ZC 3/8-16 Flanged Whiz Nut Zinc 10
6PRHD-LWA1/4ZC 1/4 Split Lock Washer 5
7PRHD-WA1/4USSGR5ZC 1/4 USS Flat Washer Zinc 4
8PRHD-HC1/4NC1/2GR5 1/4-20 x 1/2 Hex Cap Screw Zinc 1
9PRHD-HC1/4NC3/4GR5 1/4-20 x 3/4 Hex Cap Screw Zinc 4
10 PRHD-HC3/8NC2GR5ZC 3/8-16 x 2 Hex Cap Screw Grade
5 Zinc 2
5
76
8
9
10
1
11
23
4

4
Step 1
Aach the legs to the lower stand upright pole (four holes). Use the upper set of holes to
aach two of the opposite legs as shown. Aach the other two legs using the lower sets of
mounting holes with a 9/16” wrench.
TAG Item Description QTY.
1MFPB-16X16FLFT UNIVERSAL RILEY FLASH DRYER FEET-
FORMED 4
2PRHD-HC3/8NC2-1/4GR5ZC 3/8-16 X 2-1/4 HEX CAP SCREW GRADE 5
ZINC 4
3PRHD-FLN3/8NCGR5ZC 3/8-16 FLANGED WHIZ NUT ZINC 4
4MFPD-RHCRTSID RH CART SIDE PANEL (THREADED) 1
3
1
2

5
Step 2
Aach the locking casters on all four of the mounting holes of the stand with a 9/16” wrench.
The lower stand is completed.
TAG Item Description QTY.
1MFCO-CSTR2X3/8ML CASTER, MEDIUM DUTY 2" WHEEL 3/8"
STUD 4
2PRHD-FLN3/8NCGR5ZC 3/8-16 FLANGED WHIZ NUT ZINC 4
1
2

6
Step 3
Install the le and right mounting brackets to the main flash panel assembly. Use a 7/16”
wrench but do not fully tighten at this step.
TAG Item Description QTY.
1MFZC-16X16FLBKT1 & 2 UNIVERSAL FLASH DRYER MOUNTING
BRACKET (LH & RH) 2
2PRHD-WA1/4USSGR5ZC 1/4 USS FLAT WASHER ZINC 4
3PRHD-LWA1/4ZC 1/4 SPLIT LOCK WASHER 4
4PRHD-HC1/4NC3/4GR5 1/4-20 X 3/4 HEX CAP SCREW ZINC 4
3
1
2
4

7
Step 4
Install the hand lever on the desired side of the mounting channel. Install this based on which
side of the press you are using the flash dryer and whether you are right- or le-handed.
Use a 7/16” end wrench and fully tighten the knob.
TAG Item Description QTY.
1PRHD-HC1/4NC1/2GR5 1/4-20 X 1/2 HEX CAP SCREW ZINC 1
2PRHD-LWA1/4ZC 1/4 SPLIT LOCK WASHER 1
3MFCO-HANDLEVER HAND LEVER KNOB TAPERED 3" LONG 1
1
2
3

8
Step 5
Aach the upper stand upright pole to the mounting brackets of the flash dryer with a 9/16”
wrench. The upper holes of the bracket have adjustments to set the angle of the flash dryer.
This can be adjusted at the final stage once installed into the lower stand assembly. Fully
tighten the 7/16” hardware from step 3 aer installing this set of hardware.
TAG Item Description QTY.
1MFMS-FLUPRTUBE UPPER FLASH DRYER STAND TUBE 1
2PRHD-HC1/4NC3/4GR5 1/4-20 X 3/4 HEX CAP SCREW ZINC 2
3PRHD-FLN3/8NCGR5ZC 3/8-16 FLANGED WHIZ NUT ZINC 2
1
2
3

9
Step 6
Install the locking collar and fluted knob to the upper stand pole. This will set the overall height
of the flash dryer. This can be adjusted once at press to the desired distance from the platen.
TAG Item Description QTY.
1PRCO-KNBFLT3/8NC1-1/4ML FLUTED BRACKET 3/8-16 X 1-1/4" MALE
STUD 1
2PRHD-CALR1INPIPE 1-3/8" ID LOCKING COLLAR 1
3MFMS-FLUPRTUBE UPPER FLASH DRYER STAND TUBE 1
3
1
2

10
Step 7
NOTE: UNPLUG FLASH DRYER WHEN NOT IN USE.
DO NOT LEAVE THE UNIT UNATTENDED WHILE UNDER POWER.
Slide the upper flash assembly into the lower stand assembly. Make any final adjustments
to the overall height of the flash dryer. Once at press, you can also make any adjustments
needed to the tilt angle of the flash panel. Plug the unit into a standard 110v 15 amp outlet to
begin use.