RILYSON SS009 User manual

SKU#SS009
For any missing or damaging parts, hardware, or any other problems,
WELCOME to email us at:
1/4
1/4

• Please read through the instructions before beginning assembly.
• Two adults are recommended for assembly.
• Clear out the space for assembly and lay out all of the parts based on the Parts List, extra room will allow
you to easily determine if all the pieces are present.
• Save all packing materials until assembly is complete to avoid accidentally discarding smaller
parts or hardware.
• Keep small parts and pieces away from children until fully assembled.
• Use on even surfaces only.
• Improper use of this product or failure to use as directed may result in injury.
• Ensure that all bolts are securely tightened before use. It is recommended that you re-check all nuts and bolts
illdtiht
• Do not swing in the chair beyond the parameter of the base as doing so may result in the chair tipping over and
ld lt i i j
PANEL AND FITTINGS IDENTIFICATION:
Right Arm (B)
Qty:1 Qty:1 Qty:1
HARDWARE LIST:
Back (C)Left Arm (A)
Seat Panel (D) Seat Cushion (I) Back Cushion (J)
Qty:1 Qty:1 Qty:1
Long Bolts (F) Washers (G) Hex Key (H)
Qty: 4 Qty: 6 Qty: 10 Qty: 1
Short Bolts (E)
2/4

STEP-BY-STEP ASSEMBLY:
Step 1: Attach left arm (A) and right arm (B) to chair back (C) with 4 long bolts (F) and 4
washers (G) using hex key (H). Do not fully tighten bolts.
1
Step 2: Attach seat panel (D) to chair back (C) with 2 long bolts (F) and 2 washer (G)
using hex key (H). Do not fully tighten bolts.
2
3/4
3/4

Step 3: Attach seat panel (D) to left arm (A) and right arm (B) with 4 short bolts (E) and
4 washer (G) using hex key (H). Verify the alignment and adjust, then fully tighten all
the bolts.
3
Step 4: Turn over the assembled chair, and put the seat cushion (I) and back cushion
(J) onto the chair.
4
I
J
4/4

SKU#SS010
For any missing or damaging parts, hardware, or any other problems,
WELCOME to email us at:
1/3

• Please read through the instructions before beginning assembly.
• Two adults are recommended for assembly.
• Clear out the space for assembly and lay out all of the parts based on the Parts List, extra room will allow
you to easily determine if all the pieces are present.
• Save all packing materials until assembly is complete to avoid accidentally discarding smaller
parts or hardware.
• Keep small parts and pieces away from children until fully assembled.
• Use on even surfaces only.
• Improper use of this product or failure to use as directed may result in injury.
• Ensure that all bolts are securely tightened before use. It is recommended that you re-check all nuts and bolts
illdtiht
• Do not swing in the chair beyond the parameter of the base as doing so may result in the chair tipping over and
ld lt i i j
PANEL AND FITTINGS IDENTIFICATION:
TABLE TOP (A) LEGS (B) TABLE TRAY (C)
Qty: 12 Qty: 12 Qty: 1
Qty:1
HARDWARE LIST:
Qty:1 Qty:1
BOLTS (D) WASHERS (F) HEX KEY (G)
2/3

STEP-BY-STEP ASSEMBLY:
Step 1: Attach the 4 legs (B) to table top (A) by 8 bolts (D) and 8 washers (F) with hex
key (G). Do not fully tighten bolts now.
1
Step 2: Attach table tray (C) to 4 table legs (B) by 4 bolts (E) and 4 washers (F) with
hex key (G). Turn over the assembled table, verify the alignment and adjust, then fully
tighten all the bolts.
2
3/3

SKU#SS011
For any missing or damaging parts, hardware, or any other problems,
WELCOME to email us at:
1/4

• Please read through the instructions before beginning assembly.
• Two adults are recommended for assembly.
• Clear out the space for assembly and lay out all of the parts based on the Parts List, extra room will allow
you to easily determine if all the pieces are present.
• Save all packing materials until assembly is complete to avoid accidentally discarding smaller
parts or hardware.
• Keep small parts and pieces away from children until fully assembled.
• Use on even surfaces only.
• Improper use of this product or failure to use as directed may result in injury.
• Ensure that all bolts are securely tightened before use. It is recommended that you re-check all nuts and bolts
illdtiht
• Do not swing in the chair beyond the parameter of the base as doing so may result in the chair tipping over and
ld lt i i j
PANEL AND FITTINGS IDENTIFICATION:
Left Arm (A)
Qty:1
HARDWARE LIST:
Qty:1 Qty:1
Right Arm (B) Back (C)
Seat Panel (D) Seat Cushion (I) Back Cushion (J)
Qty:1 Qty:1 Qty:2
Long Bolts (F) Washers (G) Hex Key (H)Short Bolts (E)
Qty: 4 Qty: 7 Qty: 11 Qty: 1

STEP-BY-STEP ASSEMBLY:
Step 1: Attach left arm (A) and right arm (B) to chair back (C) with 4 long bolts (F) and 4
washers (G) using hex key (H). Do not fully tighten bolts.
1
Step 2: Attach seat panel (D) to chair back (C) with 3 long bolts (F) and 3 washer (G)
using hex key (H). Do not fully tighten bolts.
2
3/4
3/4

Step 3: Attach seat panel (D) to left arm (A) and right arm (B) with 4 short bolts (E) and
4 washer (G) using hex key (H). Verify the alignment and adjust, then fully tighten all
the bolts.
3
Step 4: Turn over the assembled chair, and put the seat cushion (I) and back cushion
(J) onto the chair.
4
I
JJ
4/4