Rima ONGAS MEGA 05 User manual

1
MEGA FLOOR TYPE CONDENSING BOILER
* ONGAS MEGA 05
* ONGAS MEGA 06
* ONGAS MEGA 07
* ONGAS MEGA 08
* ONGAS MEGA 09
* ONGAS MEGA 10
* ONGAS MEGA 11
* ONGAS MEGA 12
* ONGAS MEGA 13
* ONGAS MEGA 14
* ONGAS MEGA 15
* ONGAS MEGA 16
* ONGAS MEGA 17
www.rima.com.tr
INSTALLATION MANUAL

2

3
TABLE OF CONTENTS
1. General Information ..............................................................................................................................5
1.1. Introduction...................................................................................................................................5
1.2. Certificates....................................................................................................................................6
1.3.1. Explanations of the Symbols .....................................................................................................6
1.3.2. General Warnings and Recommendations.................................................................................8
1.3.2.1. Points to be Considered During Handling and Transport.......................................................8
1.3.3. Power Saving.............................................................................................................................8
1.3.4. Cascade Configuration...............................................................................................................9
1.3.5. Safety Instructions .....................................................................................................................9
1.4. Responsibilities.............................................................................................................................9
1.4.1 Things To Do Before Calling an Authorized Service.................................................................10
1.5. Explanation of the Symbols on the Packaging .............................................................................12
1.5.1. Parts Delivered With the Product ..............................................................................................13
1.6. Data and Packaging Labels...........................................................................................................13
2. General Specifications of the Condensing Boiler..................................................................................14
2.1. Components of the Floor Type Condensing Boiler......................................................................15
2.1.1. Component Neumber of the Floor Type Condensing Boiler.....................................................16
2.2. Technical Specifications of the Floor Type Condensing Boiler...................................................18
3. Installation and Commissioning ............................................................................................................20
3.1. Minimum Distances Recommended............................................................................................21
3.2. Dimensions of the Floor Type Condensing Boiler......................................................................22
3.3. Gas Connections..........................................................................................................................23
3.4. Power Connections......................................................................................................................24
3.5. Electrical Wiring Diagram...........................................................................................................25
3.6. Commissioning............................................................................................................................26
4.Operation of the Control Panel ..............................................................................................................27
4.1. Control Panel Screen ...................................................................................................................27
4.2. Application Modes.......................................................................................................................28
4.3. Programming ...............................................................................................................................31
4.4. User Levels..................................................................................................................................33

4
4.5. Operation of Control Panel Accessories......................................................................................36
5. Installation and Inspection of the Piping ...............................................................................................37
5.1. Heating (Radiator) Water.............................................................................................................37
5.1.1. Water Conditioning...................................................................................................................37
5.1.2. Water Pressure..........................................................................................................................37
5.2. Discharging of the Condensate....................................................................................................38
5.3. Instructions for the Adjustment of Gas Ratio..............................................................................39
5.3.1. Instructions for the Adjustment of Gas Ratio...........................................................................39
5.4. Flue Connections......................................................................................................................... 42
5.4.1. Examples of Installation ...........................................................................................................42
5.5. Hydraulic Piping Connection Diagram Examples ………………..………………...……...43
6.Error Codes List......................................................................................................................................44
7.Cleaning and Maintenance .....................................................................................................................51
7.1. Inspection of the Burning System................................................................................................53
7.2. Cleaning of the Modulated Fan, Venturi, Burner ........................................................................53
8.Warranty Conditions and Commissioning ..........................................................................................53
8.1. Condensing Boiler Commissioning Form .................................................................................. 54
8.2. Operating Instructions .........................................................................................................55
8.3. Inspection of the Condensing Boiler System..............................................................................56

5
1.GENERAL INFORMATION
1.1.Description
First of all, we would like to thank you for choosing the RIMA brand.
In this manual, you will find installation and operation information for the RIMA branded floor type
natural gas condensing heating boilers with aluminum cast fins manufactured by ÖNMETAL.
Please read this booklet carefully in order to operate your device with high efficiency and
economically, comfortably and for a long period.
DO NOT tamper with any component or setting of your device for any reason other than as described
in this manual, such as operating, adjusting, or maintaining the device.
Have your device installed by Authorized Dealers.
Our Authorized Dealers and After-sales Service Centers shall provide you with the necessary
information about the operation and maintenance of your device after placing the device, making the
required connections and commissioning it.
In case you cannot contact with our Authorized Services and for any problems you have, our Central
Technical Service shall help you.
We wish you to use your boiler in good times.
1.2.Certificates
Önmetal Döküm Sanayi ve Tic. Ltd. Şti. is certified with the Certificate of Competency with After-
sales Services as per TS 12676 Authorized Services - The Rules for the Boilers and Heat Exchangers
as the scope of the service dated and numbered 14.09.2011/0 and issued by the T.R. MINISTRY OF
CUSTOMS AND TRADE’s Directorate General of Consumer Protection And Market Surveillance,
and with the Service Place Competency Certificate issued by TSE.
The structure and operation of the boilers comply with the Regulations of European Union and the
conditions stipulated in the regulations of all countries in which the European Union Standard is
applicable.
ONGAS MEGA Series Floor Type Condensing Boilers are the registered brands of Önmetal Döküm
Sanayi ve Tic. Ltd. Şti. and they are manufactured in the own facilities of the company in Edirne,
Turkey.
2016/426/EU –Gas Appliances Regulation
2014/35/EU –Low Voltage Directive
2014/30/EU –Electromagnetic Compatibility Directive
92/42/EEC –Efficiency Directive
813/2013/EU –Ecodesign Regulation
2009/125/EC –Ecodesign Requirements Directive (implementing directive)
RIMA ONGAS MEGA Floor Type Condensing Boilers comply with the EC Directives.

6
1.3.1.Explanations of the Symbols
Warning Signs
Safety Warnings are indicated with a warning triangle.
Important information for the safety of persons are indicated with the symbol on the left
1.3.2.General Warnings and Recommendations
• ONGAS MEGA Series Floor Type Condensing Boilers with Aluminum Cast Fins are
designed to be used in heating installations with domestic hot water and/or in domestic hot
water installations and manufactured with the technology and materials suitable for this
design. They shall not be used for this intended use.
• While placing the boiler in the boiler room, the point where the boiler shall be installed and operated
shall have a concrete base that is stable and strong enough to bear the weight of the boiler.
• ONGAS MEGA Series Floor Type Condensing Boilers are delivered without circulation pumps
• Example installation diagrams are provided at the end of the manual. Installations for the boilers
shall be made according to these diagrams. Only the general installation principle of the system and
the sensors and relay points used for automation are provided in these diagrams. Installation elements
such as sediment traps, check valves, expansion tanks are not indicated. These equipment shall be
selected and installed separately.
• Sufficient space shall be left around the boiler while placing it in the boiler room for maintenance
and service operations.
• In the installation, a sediment trap shall be placed in the secondary circuit after the balance vessel
and an air separator shall be placed in the primary circuit after the balance tank.
• In the summer months when the boiler is not operated, the circulation pumps shall be operated for
five minutes 1-2 times a month to prevent jamming and to extend their service life. (Lime water causes
malfunctions if the boiler is not used for a long period).
• Capacity selection of the boiler shall be performed according to the installation projects prepared in
accordance with the standards. Otherwise it may not be possible to obtain the desired efficiency from
the boiler.
• ONGAS MEGA Floor Type Condensing Boilers are intended for heating systems only as standard.
Another boiler or a heat exchanger is also required to heat the domestic water. To provide efficient hot
water, the capacities of the boiler and the external boiler or heat exchanger shall be compatible.
• If the boiler has stopped automatically due to over-temperature, do not add cold water to the boiler to
restart the boiler. Wait until the boiler has cooled down and then try restarting, if it does not, inform
the authorized service.
• Electrical supply of the boiler is provided from the mains. For this reason, power and lighting
installation of the boiler room, electrical connections of the boiler, control panels and boiler room
grounding line shall be made by experts of their field in accordance with the relevant standards
• It is suitable for Vented (B type) applications, designed for central heating and optionally for the
circulation of domestic hot water.

7
• All electrical and electronic controls are supported on the control panel located at the top of the
boiler.
• The cleaning of the installation is of utmost importance for the transformation projects from
boilers with solid fuel or liquid fuel to boilers with gas fuel. The installation shall be washed, any
leaks shall be detected and repaired and a plate type heat exchanger shall be used.
• Boilers shall be installed in a place with no risk of frost. When the boiler is not operated, the water
remaining in the radiators shall be drained to prevent freezing.
• Boilers shall not be installed in a location that contains moisture, vapor or dust. Otherwise the boiler
shall not operate correctly and efficiently.
• The floor of the installation location of the boiler shall be stable, firm and wide, and it shall be
positioned high above the ground in order not to be affected by floods.
• The supply of fresh air shall be free of halogen hydrocarbons (sprays, paints and some chemicals),
otherwise these shall cause corrosion and erosion of the boiler and flue.
• Flammable materials shall not be placed on or near the boiler.
• Fresh air intake shall comply with the instructions of the local gas supplier and the instructions for
gas connection, otherwise there is a risk of poisoning.
• Condensate and flue connections shall be made in accordance with the rules and standards.
• Before starting to work on the boiler, always disconnect the main power line and turn off the main
gas valve.
• If you smell gas, turn off the main gas valve and call the emergency number for gas leaks in your
neighbourhood. If you smell flue gas, turn off the boiler and call the authorized service immediately
Combustibility (flammability) levels of construction materials and products
A- Non-combustible
Granite, sandstone, concrete, brick, ceramic, fireproof plasters
B- Very Difficult to Burn
acumin, isumin, heraclith, lignose, fiberglass components
C1- Difficult to Burn
Products made of beech or oak, hobrex plates, werzalit, umuakart
C2- Medium Combustibility
Wet wood, black pine, cork and tree crumbs, rubber sole
C3- Easy to Burn
Asphalt Components, Fiber components, cellulose materials, polyurethane, polystyrene, PVC, polyethylene
Keep the boilers at least 200 mm away from flammable materials with B, C1, C2 burning classes as
specified in the table during their installation and operation.
• For materials that burn rapidly and by themselves after any spark, that are easily ignitable with a
burning class of C3, increase the safety distance to at least 400 mm.
The boiler is set for natural gas H/E (G20, 20 mbar) in the factory.
• The boiler shall only be installed in a room that meets proper ventilation requirements and that is
separated from living areas. Otherwise there is a risk of suffocation or poisoning.
• To prevent incorrect circulation, control valves shall be used in conjunction with the circulation
pump system. A strainer (filter) shall be used in the return water lines of the new/old buildings and
new/old installation systems.

8
• A relief valve (max. 6 bar) and a manometer shall be used in the installation system. No other valves
shall be present between the boiler and the relief valve, otherwise pipes or other parts may explode in
the over-pressurized boiler (risk of evaporation).
• Supply of cold water to the boiler shall be performed when the boiler is cold.
• It is possible that oxygen may pass through the floor heating pipes into the water. Oxygen in the
water causes corrosion of the boiler. Therefore, if the boiler is to be used in a floor heating system, a
heat exchanger shall be added to the circuit and mixing of the boiler water and installation water shall
be prevented.
• The external air sensor is delivered with the device as standard to ensure more economical operation
of the boilers. This sensor allows fuel savings about 35%. Moreover, optional controller units may be
installed to allow scheduling of the boiler. Similar applications are also implemented in cascade
systems.
The boiler shall only be installed in a room that meets proper ventilation requirements and that is
separated from living areas. Otherwise there is a risk of suffocation or poisoning. Read the technical
instructions before installation and operation.
1.3.2.1.Points to be Considered During Handling and Transport
Products are shipped on pallets as protected by styrofoam and film.
The products are fastened to the pallets with retaining screws.
In addition, the products are protected with a wooden case against external impacts.
Appropriate markings are provided on the case. During storage, it may be stored at proper ambient
humidity and temperature without opening the package.
1.3.3.Power Saving
The proper use of energy resources in our world is a real problem of modern
societies. While we are generating energy for our future, we use natural resources that shall
be exhausted in the near future unless we encourage more rational and efficient use of these
resources.
Condensation technology is a big step towards the rational use of energy as it provides energy savings
of up to 35% and lower emission values (80% for CO and 90% for NOx) compared to conventional
heating systems.
Moreover, the annual CO2emission values of high efficiency condensing boilers are 20% less in
average than the boilers with standard efficiency.
In the countries that have advanced in technology, all of the new boiler installations are selected as
condensing boilers and the governments have started to encourage persons to choose this technology.
The device offers intuitive and advanced diagnostic systems that allows detection of faults by the user.

9
1.3.4.Cascade Configuration
The use of floor type condensing boilers in central systems is increasing every day. Condensing
boilers designed for this purpose provide high capacities with low space requirement. An
advantageous and economical heating is ensured by reaching a capacity of 49440 kW in one boiler and
a max. capacity of 3090 kW with a cascade system. It allows easy installation and easy operation with
its compact design which reduces the space requirement. Provides ease of installation in confined
spaces thanks to its easily accessible internal structure. ONGAS MEGA series provide excellent
compatibility when they are installed to replace old systems that have expired their service life.
Condensation technology with advanced control systems reduces your fuel costs by 30%- 40% by
providing fuel savings from the first day of operation. Allows cascade operation even in areas with a
very limited installation space thanks to its compact design and light weight.
1.3.5. Safety Instructions
The boiler is connected to 380V mains.
An incorrect installation or any attempts to repair using incorrect electrical components may
pose a lethal risk.
Keep unauthorized personnel away from the boiler. Do not leave any objects on or near the
boiler.
Do not touch the hot water connections or the flue outlet during the operation of the boiler -
risk of burning.
Installation, repair, commissioning and maintenance operations shall only be carried out by
suitably qualified personnel. It complies with all relevant international/local standards and
certificates.
Before starting to work on the boiler, always disconnect the main power line and turn off the
main gas valve.
If you smell gas, turn off the main gas valve and call the emergency number for gas leaks in your
neighborhood. If you smell flue gas, turn off the boiler and contact the authorized service or the
installer.
1.4. Responsibilities
Manufacturer’s Responsibilities: They shall manufacture and ship products in accordance with the
relevant directives
Responsibilities of the Contractor: Contracting company is responsible for the installation. The
company shall read this manual and follow the instructions provided in the manual before calling the
authorized service.

10
1.4.1.Points to Consider Before Contacting the Authorized Service
First of all, we would like to thank you for choosing and using the “Rima Condensing Boiler”. Below
is a list of things to do before calling the Rima Authorized Service.
Protect your device against factors that may damage the packaging and the device (moisture,
water, impact, construction materials, etc. ) during the transport and subsequent assembly of
the device. The boilers shall be installed on a stable, firm ground. In case of a surface which is
not suitable for supporting of the boilers and the connection equipment, a suspension system
with a metal profile shall be used.
The installation water shall be conditioned by considering whether the system is a new heating
system to be installed or an heating system to be transformed. If the installation to be used for
the system is old or if it shall be transformed, the water in the installation shall be completely
drained and water shall be conditioned (cleaning shall be performed and a preservative shall
be used). We recommend the use of plate heat exchangers in such systems particularly. The
presence of blockages in the heating installation such as dirt, sediment, burrs, iron dust, lime,
etc., adversely affect the operation of the boiler. This may cause inefficient operation,
overheating, noisy operation, and damage to the heat exchanger of the boiler over time.
Installation water shall be conditioned and preserved in new installations.
o7<pH value used in the installation> 8.5
oFor the hardness of the water, the hardness value appropriate to the capacity shall be
determined in accordance with the table given below.
Total capacity
(kW)
Total hardness (French hardness - ° F)
Total volume of
the system (less
than 20 l/kW)
Total volume of
the system
(between 20-50
l/kW)
Total volume of
the system
(higher than 50
l/kW)
>600
<0.2
<0.2
<0.2
Water containing sediment or of unknown content such as well water and transport water shall
not be used. Use of any chemicals by adding them to the installation without the approval of
the manufacturer shall render the products void of warranty. As Rima Heating Systems, we
recommend use of water treatment products with Sentinel X100, X300 or X400 brands. Use
neutral, non-acidic and non-alkaline cleaners. Any damage to the product or installation that
may occur without taking the approval of the manufacturer in applications performed using
the products of different companies is out of warranty cover. It is the user’s responsibility to
ensure that the water to be circulated in the installation is clean.
Sub-boiler pumps, hydraulic sets, balance vessels, sediment traps, air separators to be used in
the installation shall be selected as suitable to the boiler and heating installation.

11
Selection of the Balance Tank
A separate flue outlet shall made for each boiler and each flue shall be connected to the main
flue from the sides. In case of connection to existing flues, make sure that they are clean,
otherwise the flues may prevent the passing of gases during operation.
All electrical installations are the responsibility of the contractor. Connect your device to a
380 V single phase and grounded power supply. Connections to the boiler shall be performed
by the authorized service. All connections to be made on the electrical panel through the boiler
shall be performed by Rima authorized service centers. If it is desired that the electrical
installation is also performed by the authorized service, labor costs shall be subject to a charge
to be determined by the service.
A certificate of conformity shall be taken from the gas companies before calling the service.
ONGAS MEGA may only be operated with natural gas. Gas pressure in the gas line shall be
set to 21 mbar with a regulator and a filter shall be present in the gas line.
Any leaks in the installation shall be repaired. Faults and damages that may occur due to
power-water-gas installations and/or installation equipment, leaks in the installations,
installation connections, and flue connections are out of the warranty cover. Automatic supply
shall not be applied.
The systems where our gas fueled condensing boilers shall be installed are closed-circuit
systems. In closed-circuit systems, a closed expansion tank shall be used. An open expansion
tank shall not be used.
The application pressure of the system is between 0.8 bar and 6 bar. Since the closed-circuit
operating pressure allowed by the boiler is maximum 6 bar, a balance vessel shall be used for
pressures up to 6 bar, and a plate heat exchanger shall be used instead of the balance vessel for
pressures over 6 bar in cascade systems. A relief valve with adjustable pressure is not allowed.
When a plate heat exchanger is used, expansion tanks with suitable capacity shall be used on
both sides of the system

12
The boiler drainage shall be directed so that flowing of the condensation water is allowed. The
materials used for the installation the condensate drainage shall be made of plastic. Blocking
the condensate drain shall cause the boiler to shut down automatically or leak from the siphon.
If you suspect a frost condition, it shall be useful to pour hot water into the exposed part of the
drain. Always ensure that the drain is open to ensure that the boiler functions properly.
It is essential to use a manometer that indicates the operating pressure in the system.
Procurement of the zone control module and its installation to the boiler control panel is the
responsibility of the user.
The heating system has a protection function for conditions with a risk of frost. To enable this
function, the power to the boiler room shall be switched on
Faults and damages that occur due to the environmental conditions and incorrect storage by
the consumer are not covered by the warranty.
IMPORTANT: If deficiencies in the system are detected by the service personnel during the
commissioning, our service shall not commission the system; and the service fee incurred when the
service is called again for commissioning following the provision of the necessary conditions in the
system shall be borne by the user.
Responsibilities of the User: Reading the manuals, maintaining and preserving the product in
accordance with the warranty conditions, and preventing the intervention of persons other than the
authorized service.
1.5. Explanation of the Symbols on the Packaging
Fragile Top side Recycle Protect Against Water
All gas devices shall be installed by qualified technicians. Any error in the installation of these devices
may result in criminal actions as required. RIMA ONGAS MEGA condensing boilers shall not be
installed or modified in any way other than those specified in this manual. Always keep the boiler in
its safety packaging during its transport before installation. Additional protection measures may when
required by the installation site. Please follow the rules and instructions for the authorization of the
installation.

13
Packaging Label:
1.5.1. Parts Delivered as Standard with the Product
Siphon Assembly
Operating Manual
Warranty Certificate
Important: Operating instructions to ensure that the boiler may be used without any problem for many
years are included in the operating manual.
Gas Type Label
The boiler is set for natural gas H/E (G20, 20 mbar) in the factory.

14
1.6.Data Label
2. GENERAL SPECIFICATIONS OF THE CONDENSING BOILER
2.1.Components of the ONGAS MEGA Floor Type Condensing Boiler

15
2.1.Spare part of the ONGAS MEGA Floor Type Condensing Boiler

16

17

18
2.2. Technical Specifications of the Floor Type Condensing Boiler
ONGAS MEGA Serisi
ONGAS
MEGA 05
ONGAS
MEGA 06
ONGAS
MEGA 07
ONGAS
MEGA 08
ONGAS
MEGA 09
ONGAS
MEGA 10
ONGAS
MEGA 11
Heat input (max)
kW
800
1000
1200
1400
1600
1750
1900
Heat input (min)
kW
100
120
140
180
190
210
230
Heat output (max) –Rated (80/60°C)
kW
778
970
1170
1360
1560
1700
1850
Heat output (max) –Rated (50/30°C)
kW
830
1050
1260
1460
1680
1830
1990
Calorific efficiency –Rated (80/60°C)
%
97,3
97,2
97,2
97,2
97,2
97,2
97,2
Calorific efficiency –Reduced
(80/60°C)
%
96,2
96,9
96,9
96,8
96,9
96,9
96,9
Calorific efficiency –Rated (50/30°C)
%
96
96,3
96,3
96,2
96,3
96,3
96,3
Calorific efficiency –Reduced
(50/30°C)
%
104
104,7
104,7
104,2
104,7
104,7
104,7
Calorific efficiency –Partial (30°C)
%
107,4
107,4
107,4
107
107,4
107,4
107,4
NOx class
6
Max. central heating temperature
°C
80
Max. domestic hot water temperature
°C
65
Operating pressure (min –max)
bar
0,8-6
DB Level (kazandan 1 mt)
dB
Weight
kg
Power Supply
V/Hz
IP Class
IP
Power Consumption
W
Water inlet (return) & outlet (flow)
DN 125
Gas inlet
2”
Flue gas outlet (Ø)
200
250
Flue gas type
B23
Flue gas temperature –Rated
(80/60°C)
68,3
68,7
68,7
69,9
68,7
68,7
68,7
Flue gas temperature –Reduced
(80/60°C)
59
57,7
57,7
56,4
57,7
57,7
57,7
Flue gas temperature –Rated
(50/30°C)
45,2
44,1
44,1
44,2
44,1
44,1
44,1
Flue gas temperature –Reduced
(50/30°C)
30,6
30,2
30,2
30
30,2
30,2
30,2
Waste gas output flow rate at full load
Waste gas output flow rate at
minimum load
pascal
CO2at Pmax
CO2at Pmin
CO O2=0% at Pmax
CO O2=0% at Pmin
NOx O2=0% at Pmax
NOx O2=0% at Pmin

19
ONGAS MEGA Serisi
ONGAS
MEGA 12
ONGAS
MEGA 13
ONGAS
MEGA 14
ONGAS
MEGA 15
ONGAS
MEGA 16
ONGAS
MEGA 17
Heat input (max)
kW
2050
2200
2450
2700
2900
3100
Heat input (min)
kW
245
230
285
305
330
360
Heat output (max) –Rated (80/60°C)
kW
1990
2140
2380
2620
2800
2995
Heat output (max) –Rated (50/30°C)
kW
Calorific efficiency –Rated (80/60°C)
kW
2150
2340
2565
2820
3040
3230
Calorific efficiency –Reduced (80/60°C)
kW
Calorific efficiency –Rated (50/30°C)
%
97,2
97,7
97,2
97,2
97,2
96,6
Calorific efficiency –Reduced (50/30°C)
%
96,4
97
96,3
96,3
96,3
96,1
Calorific efficiency –Partial (30°C)
%
104,7
106,3
104,7
104,7
104,7
104,1
NOx class
%
107,4
108,2
107,4
107,4
107,4
107,1
Max. central heating temperature
%
108
108,2
108
108
108
107,4
Max. domestic hot water temperature
6
Operating pressure (min –max)
°C
80
DB Level (kazandan 1 mt)
°C
65
Weight
bar
0,8-6
Power Supply
dB
IP Class
kg
Power Consumption
V/Hz
Water inlet (return) & outlet (flow)
IP
Gas inlet
W
Flue gas outlet (Ø)
DN 125
Flue gas type
2”
Flue gas temperature –Rated (80/60°C)
Flue gas temperature –Reduced (80/60°C)
B23
Flue gas temperature –Rated (50/30°C)
68,7
67,9
68,7
68,7
68,7
68,7
Flue gas temperature –Reduced (50/30°C)
61,5
61,7
61,5
61,5
61,5
61,5
Waste gas output flow rate at full load
57,7
57,8
57,6
57,7
57,7
57,7
Waste gas output flow rate at minimum
load
44,1
42,9
44,1
44,1
44,1
44,1
CO2at Pmax
30,2
30
30,2
30,2
30,2
30,2
CO2at Pmin
pascal
CO O2=0% at Pmax
CO O2=0% at Pmin
NOx O2=0% at Pmax
NOx O2=0% at Pmin
Heat input (max)

20
3. INSTALLATION AND COMMISSIONING
3.1.Packaging and Handling
ONGAS MEGA Series condensing boilers are dispatched as covered with sheets coated with powder-
static paint, wrapped with stretch film, on pallets and inside crates. Appropriate markings are provided
on the case. During storage, it may be stored at proper ambient humidity and temperature without
opening the package.
Recommended minimum distances for floor type boilers:
ONGAS Mega Series condensing boilers shall be placed as follows;
•Place the boiler to the boiler room taking the minimum recommended distances into account.
•Remove the gelatin, tapes, pallets and any other packaging.
•All gas appliances shall be installed by authorized persons as required by law. Any error in the
installation of these devices may cause loss of life and property.
•Boilers shall be installed in a place with no risk of frost. When the boiler is not operated, the
water remaining in the radiators shall be drained to prevent freezing.
•Boilers shall not be installed in a location that contains moisture, vapor or dust. Otherwise the
boiler shall not operate correctly and efficiently.