Rivers Edge Treestands RELAX WIDE RE631 User manual

Operator's Manual
One-Man
Ladder Stands
GAS/OIL
RATIO
50:1
P/N: OMRELD001
REV3: 02/17/15
© 2015 RETI
All Rights Reserved.
Get parts online at
www.HuntRiversEdge.com
PACKNSTACK™
Model RE622 JUMBO JACK™
Model RE628
RELAX™ WIDE
Model RE631
Wear Your
Harness!
INCLUDES MODEL #'s:
RE622, Pack-N-Stack™
RE627, Oasis™
RE628, Jumbo Jack™
RE631, Relax™ Wide

Check for parts online at www.HuntRiversEdge.com or call 800-450-EDGE (3343) M-F 8-52
Operator's Manual
Rivers Edge® One-Man Ladder Stands
WARRANTY
Rivers Edge Tree Stands, Inc. (“RETI”) oers a one year warranty for all components of the treestand. These warranties apply to the original owner with a
proof of purchase. These warranties begin on the date of purchase by the rst retail consumer and continue for the period specied above. These warranties
apply to products that are not modied, abused or used in a manner that deviates from the product’s intended usage. Minor fading in color is normal and is
not covered by warranty. Any corrosion of painted surfaces that occurs as a result of paint being removed or damaged is also not covered by warranty. RETI
oers no other warranty expressed or implied. Products for which warranty work has been approved must be sent directly to RETI and performed by RETI.
To obtain warranty service and/or replacement instructions, you must obtain prior approval from Rivers Edge® Treestands before shipping your
package to us by calling our customer service department at 800-450-EDGE (3343) or by writing to: Rivers EdgeTree Stands, Inc., P.O. Box 755, 1160
Eighth Avenue, Cumberland, WI 54829 for a return material authorization number (RMA#). All items must be shipped prepaid. RETI will, at no charge,
repair or replace, in RETI’s sole discretion, any product that satises the conditions stated above. RETI retains the right to change models, specications and
price without notice.
This equipment has been manufactured under strict quality and safety guidelines. As with any equipment of this type, full understanding of the instructions
and its use is mandatory and imperative for the safety of its user. RETI is not responsible for any damages or injuries sustained due to improper use or
modication of any of its products, or resulting from any use which deviates from the product’s intended usage. RETI is not responsible for any injuries
sustained due to failure to read and adhere to the instructions for use. Any misunderstanding or questions regarding the products of their use should be
directed to RETI prior to any use. All RETI treestands are sold with a full body harness (“Fall Arrest System”) that meets standards set by the Treestand
Manufacturer’s Association (“TMA”). It is the owner's sole responsibility to inspect the product regularly for damage, improper installation, or conditions
that could jeopardize the ultimate safety of the product. Failure to use or improper use of the provided Fall Arrest System may result in serious injury or death.
ALWAYS wear the provided Fall Arrest System while using this product. Owner is responsible to understand and follow product eld weight rating
and must never exceed maximum weight rating. RETI is not responsible for any malfunction or injury resulting from normal wear and tear, damage caused
by improper use, improper maintenance, negligence or accidents. This product, if used safely as intended, will provide trouble free service for the useful life
of the product. We hope you will enjoy the quality of our products for years to come, and have a safe hunt.
For replacement parts, phone 800-450-EDGE (3343) or go online to www.HuntRiversEdge.com.
INTRODUCTION
Rivers Edge® Treestands are engineered with you the hunter in mind. We appreciate your purchase of one of our world
class treestands. Follow these few simple instructions and your stand will provide you many years of trouble-free plea-
sure. Instructions should be kept in a safe place and reviewed at least annually.
If for any reason you have a problem with your product, DO NOT return to the retailer, contact the Rivers Edge® cus-
tomer service department at 800-450-EDGE (3343) for assistance.
CONTENTS
Introduction/Warranty ..................................................................................................................................................................................................................2
Warnings.............................................................................................................................................................................................................................................3
Inspection and Maintenance ......................................................................................................................................................................................................4
Assembly/Parts Explosion/Parts List (RE622) ....................................................................................................................................................................5-9
Assembly/Parts Explosion/Parts List (RE627) ...............................................................................................................................................................10-19
Assembly/Parts Explosion/Parts List (RE628) ...............................................................................................................................................................20-29
Assembly/Parts Explosion/Parts List (RE631) ...............................................................................................................................................................30-35
Set-Up and Use Instructions (All ladders in this manual).........................................................................................................................................36-37
Bolt Guide ....................................................................................................................................................................................................................................... 38

Check for parts online at www.HuntRiversEdge.com or call 800-450-EDGE (3343) M-F 8-5 3
Operator's Manual
Rivers Edge® One-Man Ladder Stands
WARNINGS
WARNING
DO NOT USE THIS PRODUCT UNTIL YOU HAVE WATCHED
THE INCLUDED TREESTAND SAFETY DVD, UNDERSTAND
IT AND PRACTICED THE TECHNIQUES FOR SAFE HUNTING
DISCUSSED IN THIS DVD.
YOU MUST ALWAYS USE THE PROVIDED FULL BODY
HARNESS FALL ARREST SYSTEM THAT MEETS TMA
STANDARDS WHILE USING THIS PRODUCT. SINGLE SAFETY
BELTS AND CHEST HARNESSES ARE NO LONGER ALLOWED
AND SHOULD NEVER BE USED.
IF YOU ARE NOT WEARING A FULL BODY HARNESS THAT
IS PROTECTING YOU FROM A FALL, DO NOT LEAVE THE
GROUND.
FAILURE TO USE OR IMPROPER USE OF THE PROVIDED FULL
BODY HARNESS FALL ARREST SYSTEM THAT MEETS TMA
STANDARDS MAY RESULT IN SERIOUS INJURY OR DEATH!
READ, UNDERSTAND AND FOLLOW ALL INSTRUCTIONS. IF ANY
INSTRUCTIONS ARE NOT UNDERSTOOD OR IF YOU HAVE A
PARTS ISSUE CALL 800450EDGE 3343 BEFORE USING.
READ, UNDERSTAND AND FOLLOW ALL ASSEMBLY,
INSPECTION, MAINTENANCE, FULL BODY HARNESS FALL
ARREST SYSTEM & USE INSTRUCTIONS PROVIDED BEFORE
EACH USE. FAILURE TO FOLLOW ALL WARNINGS AND
INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR
DEATH.
READ AND PERFORM ALL INSPECTION AND MAINTENANCE
TASKS BEFORE EACH AND EVERY USE REPLACE ANY
QUESTIONABLE COMPONENTS IMMEDIATELY WITH RIVERS
EDGE® ORIGINAL REPLACEMENT PARTS. DO NOT LEAVE
YOUR STAND OUTDOORS  REMOVE AFTER EACH USE AND
STORE INDOORS!
INSTRUCTIONS SHOULD BE KEPT IN A SAFE PLACE AND
REVIEWED AT LEAST ANNUALLY. IT IS THE RESPONSIBILITY
OF THE TREESTAND OWNER TO FURNISH THE COMPLETE
INSTRUCTIONS TO ANY PERSON THAT WHO BORROWS OR
PURCHASES THE TREESTAND.
DOUBLE CHECK ASSEMBLY STEPS TO BE CERTAIN YOU HAVE
CORRECTLY ASSEMBLED THIS PRODUCT.
DO NOT CRUSH TUBING WHEN TIGHTENING BOLT
ASSEMBLIES! IDENTIFY AND FAMILIARIZE YOURSELF WITH
ALL PARTS BEFORE YOU START. A BOLT IDENTIFICATION
CHART CAN BE FOUND IN THE BACK.
DO NOT EXCEED THE TOTAL FIELD RATING 300 LBS.
NEVERUSEANYPRODUCTTHATHASNOTBEENMAINTAINED
OR INSPECTED PROPERLY  YOUR LIFE DEPENDS ON IT!
WHEN HUNTING FROM A TREESTAND, FALLS CAN OCCUR
ANY TIME AFTER LEAVING THE GROUND CAUSING INJURY
OR DEATH.
NEVER ATTACH TO A DEAD, ODDSHAPED, LEANING,
DISEASED, LOOSEBARKED TREE OR UTILITY POLES.
WARNING
REPLACE ANY AND ALL TREESTAND STRAPS EVERY TWO
YEARS OR WHEN ANY SIGNS OF DAMAGE OR WEAR EXIST
BEFORE.
SOME MODELS INCLUDE A FOOTREST, WHICH IS DESIGNED
AS A FOOTREST ONLY. NEVER STAND ON THE FOOTREST.
BE SURE TO RAISE AND LOWER YOUR WEAPON AND GEAR
WITH A HAUL LINE. GUN BARREL END AND ARROW TIPS
MUST BE POINTED DOWN AWAY FROM YOU.
BE SURE SEAT PAD AND/OR BUCKLES ARE SECURELY AND
CORRECTLY ATTACHED TO PREVENT ACCIDENTAL REMOVAL.
WARNING
ALL ASSEMBLY MUST BE DONE BY THREE PEOPLE IN THIS
ORDER AT GROUND LEVEL BEFORE UPRIGHTING.
NEVER EXCEED THE MAXIMUM STATED USE HEIGHT.
CHECK THE GROUND UNDER STAND TO MAKE SURE IT IS
FIRM AND LEVEL. SLOPED GROUND OR UNEVEN SURFACE
ONE SIDE ON A ROCK CAN CAUSE YOUR LADDER TO TILT
OR SHIFT OFF THE TREE AS YOU CLIMB.
CHECK EVERY LADDER SECTION CONNECTION EVERY TIME
YOU USE THE STAND BEFORE YOU LEAVE THE GROUND.
IF LADDER SECTIONS ARE SEPARATING, DO NOT USE THE
STAND.
LUBRICATION IS HIGHLY RECOMMENDED AT SLIDE
TOGETHER POINTS OF EACH SECTION TO PREVENT
BINDING. SECTIONS ARE STACKED TOGETHER BY SLIDING
SECTIONS TOGETHER, INSIDE OF EACH OTHER. SECTIONS
ARE THEN SECURED WITH SPRING LOCK PINS.
BE SURE ALL LADDER SECTIONS ARE SEATED COMPLETELY
TOGETHER ON SWEDGED OR POCKETED ENDS OF PIPE.
STABILIZER BAR MUST ALWAYS BE CORRECTLY AND SECURELY
ATTACHEDTO LADDER ANDTREE BEFORE CLIMBING LADDER.
SOME MODELS INCLUDE A MULTIPIECE STABILIZER BAR
SYSTEM. BE SURE SPRING LOCK PIN GOES THROUGH BOTH
THE EXTENSION TUBE AND THE STABILIZER BAR.
BE CERTAIN SPRING LOCK PINS ARE LATCHED SECURELY TO
PREVENT ACCIDENTAL REMOVAL.
BE SURE YOUR DOUBLE KNOTS ARE ALL SECURE ON ALL
ROPE CONNECTIONS.
NEVER ASCEND OR DESCEND LADDER WITHOUT TIE
OFF ROPES SECURELY HOLDING LADDER TO TREE AND
STABILIZER BAR SECURELY ATTACHED.

Check for parts online at www.HuntRiversEdge.com or call 800-450-EDGE (3343) M-F 8-54
Operator's Manual
Rivers Edge® One-Man Ladder Stands
INSPECTION AND MAINTENANCE SCHEDULE
FOR ALL RIVERS EDGE® PRODUCTS
   
damage.
 
 
 
repair or discard product if any damage is found.)
 
 
 
prevent noise, wear, and rust.
  
excessive heat, or rotting damage that may eect the safety of your
product. Discard any questionable product.
 
to all weld locations. (Return to factory for repair or discard product if
any damage is found.)
 
snug up any that may be loose. Be careful not to crush tubing when
tightening!
       
webbing, and strap or chain assemblies. Replace with factory new
any item or assembly that shows signs of wear, damage, kinking, or
functions incorrectly.
 
structural damage or wear.
 
missing parts.
  
parts, or altering adding or attaching anything to it except if explicitly
authorized in writing by the manufacturer.
ALWAYS…
 
 
use and save for future reference.
 
TMA standards immediately upon reaching foot platform.
 
 
 
damage before every application, replace if necessary.
 
being secure in the treestand and a re arm must be pulled up with
it unloaded, chamber open and muzzle down.
 
 
 
 
 Lubricate all slide together points to prevent binding, wear, rust and noise.
 
 
treestand will be located and the expected duration of the hunt.
 
signal are or personal locator device (PLD) and it must be readily
available at all times.
 
and do not store a treestand outdoors when not in use.
NEVER…
 
 
 
 
or utility poles.
 
than 20 inches.
 
windstorms or icy conditions and end your hunt and return to the
ground if inclement conditions arise.
 
 
 
 
prescription drugs.
 
 
 
 
 
prior medical condition that could cause a problem i.e., heart condition,
joints that lock-up, spinal fusion, etc. or if you are not well rested.
 
 

Check for parts online at www.HuntRiversEdge.com or call 800-450-EDGE (3343) M-F 8-5 5
Operator's Manual
Rivers Edge® One-Man Ladder Stands
ASSEMBLY INSTRUCTIONS RE622
Tools needed – two 7/16" wrenches
IMPORTANT ASSEMBLY TIP: DO NOT TIGHTEN NUT& BOLT COMBINATIONS
COMPLETELY UNTIL ALL PARTS ARE ASSEMBLED TOGETHER! FINGER TIGHT-
EN PLUS ONE TURN OF A WRENCH ONLY! THIS WILL TEMPORARILY HOLD THE
LOCK NUT ON THE BOLT WHILE HELPING ALIGNMENT OF ALL PARTS! AFTER
ALL PARTS ARE ASSEMBLED TOGETHER, ALL NUT AND BOLT COMBINATIONS
MUST BE COMPLETELY TIGHTENED.
1. Attach the foot platform (1ML61), mesh side up, to the 2-step ladder section
w/ stabilizer bar mount (SL64) using (2) provided 1/4-20 x 2-1/4” bolts and
locknuts. SEE FIGURE 1. DO NOT tighten all nut & bolt assemblies
completely!
NOTE: Mesh surface should be on top with squared ends of platform
closest to ladder.
2. Attach the foot platform at bars (AL7) to the foot platform and to the inside
of top ladder section side rails using (4) provided 1/4-20 x 1-1/2”bolts and
locknuts. SEE FIGURE 1.
3. Attach sling seat (48066) to assembled top sitting section by sliding each
side rail through webbing loops of seat (3 on each side of seat). Seat should
be orientated with seat straps on bottom side of seat for comfort.
NOTE: Always have all three seat loops on each side of seat at-
tached to the side rails of assembled top sitting section.
4. Attach the tree blade frame (SL67) to the side rails (SL69) using (4) provided
1/4-20 x 2-1/4”bolts, locknuts and steel washers. SEE FIGURE 2. You must
now tighten all nut & bolt assemblies. Be sure not to over tighten or
crush tubing when tightening!
5. Sections are assembled on the ground in the following order: bottom section
(SL62 ladder); second section (SL62 ladder); third section (SL63 ladder with
stabilizer bar mount); fourth section (assembled SL64 ladder with foot
platform); top section (assembled top sitting section). SEE FINISHED 13’
PACK-N-STACK LADDER LINE ART.
Figure 1
Figure 2
1/4-20 x 2-1/4" bolts
steel washers
side rails
tree blade frame
locknuts
locknuts
foot platform at bars
1/4-20 x 2-1/4" bolts
mesh foot platform
1/4-20 x 1-1/2" bolts
2-step ladder
w/stabilizer
bar mount
WARNING
FOOT PLATFORM AND SITTING SECTION MUST ALWAYS
FACE THE SAME DIRECTION, TOWARDS THE TREE.

Check for parts online at www.HuntRiversEdge.com or call 800-450-EDGE (3343) M-F 8-56
Operator's Manual
Rivers Edge® One-Man Ladder Stands
Figure 5
Figure 3
Figure 4
spring lock pins
stabilizer bar
stabilizer bar
extension tube
spring lock pins
6. With all sections assembled together on ground, secure all sections together

to the outside of ladder side rails. SEE FIGURE 3.
7. a. Attach the stabilizer bar extension tube (1ML23) to the third ladder section
mounting bracket using (1) provided spring lock pin. SEE FIGURE 4.
b. Slide the stabilizer bar (L29) into the extension tube and attach the two
pieces together using (1) provided spring lock pin. Spring lock pin must go
through both the extension tube and the stabilizer bar at appropriate hole
to achieve desired distance from tree. Adjustment in length may be needed
when ladder is uprighted later in instructions. SEE FIGURE 4.
8. a. Tie one end of the provided 9’rope to the link welded onto the stabilizer
bar, just in front of the tree hugger. Be sure your double knot is secure.
SEE FIGURE 5.
b.Tie one end of each of the provided 15’ropes to the square tube side rails
and tree blade frame, just in front of the welded on tree blade. Be sure your
double knots are secure. SEE FIGURE 5.

Check for parts online at www.HuntRiversEdge.com or call 800-450-EDGE (3343) M-F 8-5 7
Operator's Manual
Rivers Edge® One-Man Ladder Stands
RE622 BACKPACKING STRAP
ATTACHMENT INSTRUCTIONS
1. Stack metal components of the ladder AS SHOWN IN
FIGURE 1A AND 1B.
2. Lay stabilizer with extension tube along side of stacked ladder.
Wrap the provided ladder ratchet strap around the stacked frame.
-
curely hold all ladder components together.
3. Attach backpacking straps (48067) on packed ladder. Fold strap
in half. Feed folded strap through foot platform mesh and around
platform frame OR around the ladder rung located directly under-
neath the foot platform. Feed the two loose ends of strap through
folded loop and pull tight forming a cinch knot. SEE FIGURES 2A
AND 2B. Feed the two loose ends of straps around bottom group
of ladder rungs and secure with provided tri-slide buckles.
SEE FIGURE 2C.
4. Secure all ladder sections and stabilizer bar together with your ratchet strap.
Figure 1A: Stacked View
Figure 1B: Unstacked View
Figure 2A: Attaching the straps Figure 2B: Pulling the straps tight
Figure 2C: Attaching
straps to bottom

Check for parts online at www.HuntRiversEdge.com or call 800-450-EDGE (3343) M-F 8-58
Operator's Manual
Rivers Edge® One-Man Ladder Stands
FINISHED PACK-N-STACK™ LADDER
fourth section
ratchet strap
stabilizer bar
extension tube
15' tie-o ropes
9' stabilizer bar rope
spring lock pins
second section
top section
bottom section
third section

Check for parts online at www.HuntRiversEdge.com or call 800-450-EDGE (3343) M-F 8-5 9
Operator's Manual
Rivers Edge® One-Man Ladder Stands
LADDER PARTS RE622
12
3
3
2
2
13
4
1
7
1
3
6
2
11
4
10
8
4
9
9
5
14
KEY # PART # DESCRIPTION QT Y.
1 48240B  4
2 48271B  6
3 48752B  10
4 63281 
RETAINER
10
51ML23 SUPPORT TUBE, STABILIZER 1
61ML61 FOOT PLATFORM 1
7AL7 SIDE SUPPORT, FOOT PLATFORM 2
8 L29 STABILIZER BAR, 18" 1
9 SL62 SWEDGED LADDER, 38" 2
10 SL63 SWEDGED LADDER W/VAM, 38" 1
11 SL64 SWEDGED LADDER W/VAM, 38" 1
12 SL67 TREE BLADE, LADDER 1
13 SL69 SIDE RAIL 2
14 48261B  4
ITEMS BELOW NOT SHOWN
 48415  1
 10531  1
 48691 

2
 48066 SEAT, W/STIFFENER, SLING 1
 48800 DVD TREESTAND SAFETY 1
LADDER PARTS LIST RE622
Maximum Height - 12' 3" to seat
Maximum Field Rating - 300 lbs.
Tree Diameter Range - 12" to 20"
NO EXTENSIONS AVAILABLE FOR THIS MODEL.
NEVER MODIFY OR EXCEED ORIGINAL STATED USE HEIGHT!

Check for parts online at www.HuntRiversEdge.com or call 800-450-EDGE (3343) M-F 8-510
Operator's Manual
Rivers Edge® One-Man Ladder Stands
ASSEMBLY INSTRUCTIONS RE627
Tools needed – two 7/16” wrenches, one 9/16" wrench
IMPORTANT ASSEMBLY TIP: Do not tighten any nut and bolt combinations
completely until all parts are assembled together! Finger tighten plus one
turn of a wrench only! This will temporarily hold the lock nut on the bolt while
helping alignment of all parts! After all parts are assembled together, all nut
& bolt combinations must be completely tightened.
1. Attach the front platform (410050) and the rear platform (410058)
together using (2) provided 1/4-20 x 2”bolts, locknuts and steel
washers. SEE FIGURE 1. DO NOT tighten all nut and bolt assem-
blies completely!
NOTE: Mesh surface of foot platforms should be on top.
2. Attach the platform support rails (410055) to the bottom of as-
sembled foot platforms using (8) provided 1/4-20 x 2-1/4”bolts,
locknuts and steel washers. SEE FIGURE 2.
3. Attach the platform at support braces (1ML40) to the rear plat-
form and platform support rails using (4) provided 1/4-20 x 1-1/2”
bolts and locknuts. SEE FIGURE 2.
Figure 1
Figure 2
front platform
rear platform
1/4-20 x 2" bolt
steel washers
locknuts
rear platform platform support rail
at support
braces
1/4-20 x 2-1/4" bolts
steel
washers
locknuts
1/4-20 x
1-1/2" bolts

Check for parts online at www.HuntRiversEdge.com or call 800-450-EDGE (3343) M-F 8-5 11
Operator's Manual
Rivers Edge® One-Man Ladder Stands
Figure 3
ladder side rails
steel washers
1/4-20 x 2" bolt
locknuts
right
armrest
backrest mounts
1/4-20 x 3" bolts
left
armrest
1/4-20 x
2-1/4" bolts
1/4-20 x 2"
bolts
4. Attach the front of the ladder side rails (410053) to the front plat-
form using (2) provided 1/4-20 x 2”bolts (2), locknuts (4) and steel
washers. SEE FIGURE 3.
5. Attach the left armrest (410062L), right armrest (410062R) and
(2) backrest mounts (410082) to the previously assembled ladder
side rails and platform support rails using (2) provided 1/4-20 x
2” bolts, (4) 1/4-20 x 2-1/4” bolts, (2) 1/4-20 x 3”bolts, (8) locknuts
and (8) steel washers. SEE FIGURE 3.
6. Attach the tree blade (410056) to the ladder side rails using (4)
provided 1/4-20 x 2-1/4”bolts, locknuts and steel washers. SEE
FIGURE 4.
7. Attach footrest (410061) to ladder side rails using (2) provided
1/4-20 x 2-3/4” bolts, locknuts, steel washers and nylon spacers.
SEE FIGURE 5.
Figure 4
Figure 5
tree blade
1/4-20 x
2-1/4" bolts
locknuts
steel washers
ladder side rails
1/4-20 x
2-3/4" bolts
footrest
steel
washers
locknuts
nylon
spacers

Check for parts online at www.HuntRiversEdge.com or call 800-450-EDGE (3343) M-F 8-512
Operator's Manual
Rivers Edge® One-Man Ladder Stands
FIGURE 9b - Rear xed brace rotated into locked position
FIGURE 9a - Rear xed brace in vertical position
FIGURE 8c - Finger tighten locknut
FIGURE 8b - Insert 1/4-20 x 2-3/4" bolt
FIGURE 8a - Angle side rail outside of rear xed brace
FIGURE 7 - Insert 1/4-20 x 2-3/4" bolt
SEAT ASSEMBLY
8. a. Position the factory assembled mesh seat (360018) upside down
on a sturdy, hard surface. SEE FIGURE 6.
b. Insert (1) 1/4-20 x 2-3/4”bolt through the rear xed brace (410122)
and side rail of mesh seat. Finger tighten locknut (rear xed brace
locknuts will need to be removed in order to attach nished seat to
treestand later in assembly instructions). SEE FIGURE 7.
NOTE: The rear xed brace is meant to be wider than the seat. The
TearTu material is extremely durable and is meant to stretch.
SEE FIGURE 7.
c. Angle the other side rail so it is outside of the rear xed brace
to align the bolt holes. SEE FIGURE 8a. Insert (1) 1/4-20 x 2-3/4"
bolt through the rear xed brace and side rail (bolt will enter at an
angle). SEE FIGURE 8b. Finger tighten locknut to aid in further as-
sembly. SEE FIGURE 8c.
d. Rotate the rear xed brace towards the seat to lock the brace in
position. SEE FIGURE 9a and 9b.
FIGURE 6 - Factory assembled mesh seat
Rear xed brace is wider than seat.
bolt
Bolt will enter
at an angle.
locknut
locknut

Check for parts online at www.HuntRiversEdge.com or call 800-450-EDGE (3343) M-F 8-5 13
Operator's Manual
Rivers Edge® One-Man Ladder Stands
FIGURE 13 - Install previously removed bolt and locknut
FIGURE 14 - Tighten front brace bolts and locknuts (4)
FIGURE 12a - Front hinged brace in vertical position
FIGURE 12b - Front hinged brace rotated into locked position
FIGURE 11 - Insert (2) 1/4-20 x 1-1/4" bolts
FIGURE 10 - Remove "locking" bolt and hinge front brace
SEAT ASSEMBLY CONTINUED
e. Remove the factory installed "locking" bolt and locknut from the

to aid in assembly. SEE FIGURE 10.
f. Insert (2) 1/4-20 x 1-1/4" bolts through the front hinged brace and
each side rail, and nger tighten locknuts. SEE FIGURE 11. Brace
should remain hinged.
g. Rotate the front hinged brace towards the seat to lock the brace
in position. SEE FIGURES 12a and 12b.
h. Push down on the front hinged brace and install the previously
removed bolt and locknut. SEE FIGURE 13.
i. Tighten all (4) bolts and locknuts on the front hinged brace at this
time. SEE FIGURE 14. This will tighten up the side rails of the seat
to the braces and square up the entire seat.
NOTE: The rear xed brace locknuts will need to be removed in
order to attach nished seat and should not be tightened at this
time.
"locking" bolt hole location
 Push front hinged brace
down rmly.
bolt
locknut
PUSH DOWN

Check for parts online at www.HuntRiversEdge.com or call 800-450-EDGE (3343) M-F 8-514
Operator's Manual
Rivers Edge® One-Man Ladder Stands
Figure 15
Figure 16
Figure 17
shooting
rail J-pipes
shooting rail
1/4-20 x 1-1/4" bolt
1/4-20 x
2-1/4" bolts
bolt-on
ladder step
ared rails
seat assembly
1/4-20 x 2-1/4" bolts
nylon washers
locknuts
1/4-20 x
1-1/2" bolts
steel washers
locknuts
Figure 18
mesh backrest
retaining bar
1/4-20 x 1-1/2"
bolts
backrest spacer
locknuts
plastic stiening
rods
3/8-16 nut
3/8" lock washer
9. Remove the locknuts from the (2) 1/4-20 x 2-1/4”bolts that were previ-

the seat assembly to the ladder side rails using (2) provided 1/4-20 x
2-1/4”bolts, locknuts and nylon washers. SEE FIGURE 15. Make sure
all (4) angle brackets are fully cradling fabric rails.
NOTE: Mesh seat is not depicted in drawing so hardware can be visible.
10. Insert the shooting rail J-pipes (410113) into the shooting rail front
(410065) and secure together using (2) provided 1/4-20 x 1-1/4”
bolts and locknuts. SEE FIGURE 16.
11. Insert the two side rails into the ared rails (410054). Secure using
(2) provided 1/4-20 x 1-1/2”bolts, locknuts and steel washers. SEE
FIGURE 17.
12. Attach the bolt-on ladder step (410034) to the front side of ared
rails using (2) provided 1/4-20 x 2-1/4”bolts, locknuts and steel
washers. SEE FIGURE 17.
13. Attach the mesh backrest assembly (360021) and the (2) retaining
bars (410081) to the backrest mounts using (6) provided 1/4-20 x
1-1/2”bolts and locknuts. SEE FIGURE 18. The mesh backrest must
wrap around the front side of backrest mounts and the plastic sti-
ening rod located in the sewn sleeve on each side of the backrest
MUST be positioned behind the backrest retainer bars to act as a
stop and prevent the backrest from pulling out during use. All bolts
MUST go through the backrest retainer bars, the holes provided in
the backrest and the backrest mounts. SEE FIGURE 18. Temporary
removal of the backrest mount tube from the rest of the assembled
ladder top may be necessary to attach the mesh backrest. If this is
needed, re-attach backrest mount tubes with mesh backrest to the
ladder top assembly.

Check for parts online at www.HuntRiversEdge.com or call 800-450-EDGE (3343) M-F 8-5 15
Operator's Manual
Rivers Edge® One-Man Ladder Stands
Figure 19
spring lock pins
Figure 20
Figure 21
support braces
1/4-20 x 1-1/2" bolts
shooting
rail
locknuts
14. Thread the non-locking 3/8-16 nut onto the threaded end of
spacer rod all the way to the bottom of threads and slide 3/8”lock
washer on. Insert the threaded end of spacer rod through either
backrest mount tube far enough to be able to insert the opposite
end of spacer rod (end with welded-on washer) into opposite
backrest mount tube. Thread 3/8-16 nut back against mount tube.
Using a 9/16” wrench, tighten nut until mesh backrest becomes
taut. SEE FIGURE 18. You must now tighten all nut and bolt
assemblies. Be sure not to over tighten or crush tubing when
tightening!
15. Sections are assembled on the ground in the following order; bot-
tom section (410066 3-step ladder); second section (410068 3-step
ladder with stabilizer bar mount); third section (410069 3-step
ladder w/ mounting holes); top section (assembled top platform
section). SEE FINISHED 17’ OASIS LADDER.
16. With all sections assembled together on ground, secure all sec-

spring lock pin must be put to the outside of ladder side rails.
SEE FIGURE 19.
17. Attach the (2) support braces (410024) to the inside of platform
support rails and outside of top ladder section w/ mounting holes
using (4) provided 1/4-20 x 1-1/2”bolts and locknuts. SEE FIGURE
20. Tighten securely. Be sure not to over tighten or crush tub-
ing when tightening!
18. a. Attach the removable shooting rail by setting rail down over
studs provided on armrests. SEE FIGURE 21. Lubrication is rec-
ommended to prevent binding and noise.
b. Attach the (2) provided 9”and (1) provided 47”camo foam pads
to the armrests and shooting rail by wrapping around tubing and
attaching Velcro together.
c. Attach foam padded seat bumpers (48102) to bottom side of
front seat spacer assembly. Surface must be clean and at room
temperature to assure proper adhesion.

Check for parts online at www.HuntRiversEdge.com or call 800-450-EDGE (3343) M-F 8-516
Operator's Manual
Rivers Edge® One-Man Ladder Stands
Figure 22
Figure 23
stabilzier bar extension tube
spring lock pins
stabilizer bar
19. a. Attach the stabilizer bar extension tube (1ML23) to the second
ladder section mounting bracket using (1) provided spring lock
pin. SEE FIGURE 22.
b. Slide the stabilizer bar (L17) into the extension tube and attach
the two pieces together using (1) provided spring lock pin. Spring
lock pin must go through both the extension tube and stabilizer
bar at appropriate hole to achieve desired distance from tree. Ad-
justment in length may be needed when ladder is uprighted later
in instructions. SEE FIGURE 22.
20. a. Tie one end of the provided 9’rope to the link welded onto the
stabilizer bar, just in front of the tree hugger. Be sure your double
knot is secure. SEE FIGURE 23.
b. Tie one end of each of the provided 15’ ropes to the square tube
of tree blade frame, just in front of the tree blades. Be sure your
double knots are secure. SEE FIGURE 23.

Check for parts online at www.HuntRiversEdge.com or call 800-450-EDGE (3343) M-F 8-5 17
Operator's Manual
Rivers Edge® One-Man Ladder Stands
Finished Oasis™ Ladder
bottom section
second
section
third
section
top section
ratchet strap
15' tie-o
ropes
9' stabilizer
bar rope
stabilizer bar
stabilizer bar
extension tube
spring
lock
pins

Check for parts online at www.HuntRiversEdge.com or call 800-450-EDGE (3343) M-F 8-518
Operator's Manual
Rivers Edge® One-Man Ladder Stands
RE627 PARTS EXPLOSION
16
31
17
34
18
4
26
5
28
27
8
26 27
30
30
9
7
25
6
11
25
30
13
28
3
24
10
28
28
26
19
20
22
15
33
14
35
12
21
33
32 27
29
1
36
2
37
23
16
31
17
34
18
4
26
5
28
27
8
26 27
30
30
9
7
25
6
11
25
30
13
28
3
24
10
28
28
26
19
20
22
15
33
14
35
12
21
33
32 27
29
1
36
2
37
23

Check for parts online at www.HuntRiversEdge.com or call 800-450-EDGE (3343) M-F 8-5 19
Operator's Manual
Rivers Edge® One-Man Ladder Stands
KEY # PART # DESCRIPTION 6Q
1 10347  2
21ML23 TUBE, STABILIZER, SUPPORT 1
31ML40 
LADDERS
2
4 410024  2
5 410034 STEP LADDER 17" 1
6 410050  1
7 410053 RAIL SIDE LADDER 2
8 410054 RAIL SIDE FLARED LADDER 2
9 410055 RAIL PLATFORM SUPPORT 2
10 410056 WELDMENT, TREE BLADE LADDER 1
11 410058  1
12 410061 FTS FOOTREST LADDER 1
13 410062L WELDMENT ARMREST LEFT 1
14 410062R  1
15 410065  1
16 410066 WELDMENT LADDER 3 STEP 1
17 410068 WELDMENT LADDER W/MOUNT 3 STEP 1
18 410069  1
19 410081  2
20 410082  2
21 410112  1
22 410113  2
23 410118  1
24 410122  1
RE627 PARTS LIST
KEY # PART # DESCRIPTION Q T Y.
25 48153B  6
26 48240B  16
27 48261B  32
28 48271B  20
29 48280B  2
30 48752B  50
31 63281 
RETAINER
8
32 67540B  2
33 8909B  4
34 L17 WELDMENT, STABILIZER BAR 1
35 WN516  2
36 10755  1
37 719  1
ITEMS NOT SHOWN
 360018 ASSEMBLY SEAT OASIS 1
 360021  1
 48415  1
 10531  1
-- 48736  2
 48912  1
 48691 

1
 48102 PAD, BUMPER SEAT 2
 48800 DVD TREESTAND SAFETY 1
Maximum Height - 17' 2" to shooting rail
Maximum Field Rating - 300 lbs.
Tree Diameter Range - 12" to 20"
NO EXTENSIONS AVAILABLE FOR THIS MODEL.
NEVER MODIFY OR EXCEED ORIGINAL STATED USE HEIGHT!
16
31
17
34
18
4
26
5
28
27
8
26 27
30
30
9
7
25
6
11
25
30
13
28
3
24
10
28
28
26
19
20
22
15
33
14
35
12
21
33
32 27
29
1
36
2
37
23

Check for parts online at www.HuntRiversEdge.com or call 800-450-EDGE (3343) M-F 8-520
Operator's Manual
Rivers Edge® One-Man Ladder Stands
Figure 1
Figure 2
front platform
rear platform
1/4-20 x 2" bolts
steel washers
locknuts
rear platform platform support rails
at support
braces
1/4-20 x 2-1/4" bolts
steel
washers
locknuts
1/4-20 x
1-1/2" bolts
ASSEMBLY INSTRUCTIONS RE628
Tools needed – two 7/16” wrenches, one 9/16" wrench
IMPORTANT ASSEMBLY TIP: Do not tighten any nut and bolt combinations
completely until all parts are assembled together! Finger tighten plus one
turn of a wrench only! This will temporarily hold the lock nut on the bolt
while helping alignment of all parts! After all parts are assembled together,
all nut & bolt combinations must be completely tightened.
1. Attach the front platform (410083) and the rear platform (410086)
together using (2) provided 1/4-20 x 2”bolts, locknuts and steel
washers. SEE FIGURE 1. DO NOT tighten all nut and bolt assem-
blies completely!
NOTE: Mesh surface of foot platforms should be on top.
2. Attach the platform support rails (410055) to the bottom of as-
sembled foot platforms using (8) provided 1/4-20 x 2-1/4”bolts,
locknuts and steel washers. SEE FIGURE 2.
3. Attach the platform at bars (1ML40) to the rear platform and
platform support rails using (4) provided 1/4-20 x 1-1/2”bolts and
locknuts. SEE FIGURE 2.