Rivers edge Big foot xl lounger re552 User manual

Operator's Manual

Hang-On Stands

GAS/OIL

RATIO

50:1

P/N: 18051

REV5: 03/15/16

Get parts online at

www.HuntRiversEdge.com

PARTICIPATING MEMBER

PRODUCT MEETS

INDUSTRY STANDARDS

RECOGNIZED BY

BIG FOOT™ TRAVELER

Model RE513

BIG FOOT™XL LOUNGER

Model RE552

INCLUDES MODEL #'s:

RE513, Big Foot™ Traveler

RE552, Big Foot™ XL Lounger

Wear Your

Harness!

Check for parts online at www.HuntRiversEdge.com or call 800-450-EDGE (3343) M-F 8-52

Operator's Manual

Hang-On Stands

CONTENTS

Introduction/Warranty ..................................................................................................................................................................................................................2

Warnings.........................................................................................................................................................................................................................................3-4

Inspection and Maintenance ......................................................................................................................................................................................................4

Assembly Instructions (RE513) ...................................................................................................................................................................................................5

Assembly Instructions (RE552) ...................................................................................................................................................................................................6

Set Up and Use Instructions ........................................................................................................................................................................................................8

Threading the Float Buckle..........................................................................................................................................................................................................9

Parts Explosion/Parts List (RE513) .......................................................................................................................................................................................... 10

Parts Explosion/Parts List (RE552) .......................................................................................................................................................................................... 11

INTRODUCTION

Rivers Edge® Treestands are engineered with you the hunter in mind. We appreciate your purchase of one of our world

class treestands. Follow these few simple instructions and your stand will provide you many years of trouble-free

pleasure. Instructions should be kept in a safe place and reviewed at least annually.

If for any reason you have a problem with your product, DO NOT return to the retailer, contact the Rivers Edge®

customer service department at 800-450-EDGE (3343) for assistance.

WARRANTY

RETI oers a one year warranty for all components of the treestand. These warranties apply to the original owner with a proof of purchase. These warranties

begin on the date of purchase by the rst retail consumer and continue for the period specied above. These warranties apply to products that are not

modied, abused or used in a manner that deviates from the product’s intended usage. Minor fading in color is normal and is not covered by warranty.

Any corrosion of painted surfaces that occurs as a result of paint being removed or damaged is also not covered by warranty. RETI oers no other warranty

expressed or implied. Products for which warranty work has been approved must be sent directly to RETI and performed by RETI. To obtain warranty service

and/or replacement instructions, you must obtain prior approval from RETI before shipping your package to us by calling our customer service

department at 800-450-3343 or by writing to: RETI, P.O. Box 755, 1160 Eighth Avenue, Cumberland, WI 54829 for a return material authorization

number (RMA#). All items must be shipped prepaid. RETI will, at no charge, repair or replace, in RETI’s sole discretion, any product that satises the conditions

stated above. RETI retains the right to change models, specications and price without notice.

This equipment has been manufactured under strict quality and safety guidelines. As with any equipment of this type, full understanding of the instructions

and its use is mandatory and imperative for the safety of its user. RETI is not responsible for any damages or injuries sustained due to improper use or

modication of any of its products, or resulting from any use which deviates from the product’s intended usage. RETI is not responsible for any injuries

sustained due to failure to read and adhere to the instructions for use. Any misunderstanding or questions regarding the products of their use should be

directed to RETI prior to any use. All RETI treestands are sold with a full body harness (“Fall Arrest System”) that meets standards set by the Treestand

Manufacturer’s Association (“TMA”). It is the owner's sole responsibility to inspect the product regularly for damage, improper installation, or conditions

that could jeopardize the ultimate safety of the product. Failure to use or improper use of the provided Fall Arrest System may result in serious injury or death.

ALWAYS wear the provided Fall Arrest System while using this product. Owner is responsible to understand and follow product eld weight rating

and must never exceed maximum weight rating. RETI is not responsible for any malfunction or injury resulting from normal wear and tear, damage caused

by improper use, improper maintenance, negligence or accidents. This product, if used safely as intended, will provide trouble free service for the useful life

of the product. We hope you will enjoy the quality of our products for years to come, and have a safe hunt.

Check for parts online at www.HuntRiversEdge.com or call 800-450-EDGE (3343) M-F 8-5 3

Operator's Manual

Hang-On Stands

MODEL RE513 / RE552

MAXIMUM OCCUPANCY  ONE 1

TOTAL WEIGHT LIMIT  300 LB

TREE DIAMETER RANGE  8"TO 20"

WARNING

This product carries strict weight restrictions. Do Not use

this product if you exceed the total weight limit. Please

note that the total weight limit includes the user(s) and

their equipment.

WARNING

Pull up a bow, backpack, or rearm or other equipment

only after being secure in the treestand and a rearm

must be pulled up with it unloaded, chamber open, and

muzzle down.

Always inform someone of the hunting location, where

the treestand will be located and the expected duration

of the hunt.

A signal device such as a mobile phone, radio, whistle,

signal are or personal locator device (PLD) must be on

your person and readily available at all times.

Inspect the treestand and all safety devices each time

before use and Do Not store a treestand outdoors when

not in use.

Never modify your treestand in any way by making

repairs, replacing parts, or altering it except if explicitly

authorized in writing by the manufacturer.

Practice installing, adjusting and using your treestand at

ground level prior to using it at elevated positions. Study

your new stand to become familiar with all of its features

and design. Doing so will conrm that the product is

manufactured, assembled and installed correctly.

Instructions (written and video) shall be kept in a safe place

and reviewed at least annually. It is the responsibility of

the treestand owner to furnish the complete instructions

to any person who borrows or purchases the treestand.

The use of a lineman’s/climbing belt is required when

installing a hang-on treestand to stabilize the user with

the tree.

Correct tightening and adjustment of chains, cables,

straps, etc. are critical to stable hang-on treestand

installation. All treestand contact points must be in

contact with the tree before you step onto your stand.

Never leave a treestand in a tree for more than two weeks

since weather or animals could cause damage. Tree

growth can also stress and damage straps and buckles.

Practice the attachment of hang-on treestands at ground

level before using in a hunting environment. Doing so

will conrm that the product is manufactured, assembled

and installed correctly. Failure to install and test at ground

level rst puts users at risk for serious injury or death.

Use a haul line to raise and lower the treestand. Never

climb with anything on your back.

Always lean forward as you ascend or descend ladder or

climbing aid.

Never lean out over edge of device.

WARNING

When hunting from a treestand falls can occur any

time after leaving the ground causing injury or death.

Always wear a Fall Arrest System (FAS) comprising a full

body harness at all times after leaving the ground. You

must stay connected at all times after leaving the ground

while using climbing and hang-on treestands. Single

safety belts and chest harnesses are no longer allowed

and shall never be used. If you are not wearing a full body

harness properly attached to the tree that is protecting

you from a fall, do not leave the ground.

Read and understand all of the manufacturer’s Warnings

and Instructions and use all safety devices provided by

the manufacturer. Contact the manufacturer for any

questions. Failure to do so could result in injury or death.

Never exceed the total weight limit of the treestand.

Never use a treestand during inclement weather such as

rain, lightning, windstorms or icy conditions and end your

hunt and return to the ground if inclement conditions

arise.

Never use a treestand while using drugs (even

prescription drugs) or alcohol.

Never use a treestand while feeling ill, nauseous or dizzy,

or if you have a prior medical condition that could cause

a problem, that is, heart condition, joints that lock-up,

spinal fusions, etc., or if you are not well rested. Never

sleep in stand.

Never use a treestand on a dead, leaning, diseased or

loose barked tree, or a utility pole. Always avoid electrical

power lines.

Never rely on a tree branch for support.

Never jump or bounce on a treestand to seat it to the tree.

Check for parts online at www.HuntRiversEdge.com or call 800-450-EDGE (3343) M-F 8-54

Operator's Manual

Hang-On Stands

WARNING

Climbing aids (stick ladders, sectional ladders, steps, etc.)

must extend above the platform to allow the user to step

down onto the platform. Never step up to your stand from

a climbing aid. To ensure that you step down onto the

platform, the maximum recommended use height is ve

feet less than the height of the climbing aid being used.

Do Not use this product until you have watched the

included treestand safety DVD, understand it, and practiced

the techniques for safe hunting discussed in this DVD.

Read and perform all inspection and maintenance tasks

before each and every use. Replace any questionable

components immediately with RETI original replacement

parts.

Do Not crush tubing when tightening bolt assemblies!

Identify and familiarize yourself with all parts before you

start. A bolt identication cart can be found in the back.

Double check assembly steps to be certain you have

correctly assembled this product.

Never use any product that has not been maintained or

inspected properly - Your life depends on it!

Replace any and all treestand straps every two years or

when signs of damage or wear exist before.

Do Not use any type of after market hanging assists,

bracket mount systems or any other type of mechanism

to attach your hang-on treestand to a tree. These types of

devices can negatively aect the stability of the treestand

in the tree and reduce or prevent proper tightening, tree

adhesion and performance of the treestand to the tree

which can lead to serious injury or death.

Platform must be folded up to remove stand! This allows

slack in strap for removal.

Always climb tree on the oat buckle side of this treestand.

Visually inspect that both sewn loop attachments are

securely connected to be assured you have correctly

attached stand to tree as per instructions and Figures.

Always wear the appropriate footwear when using a hang-

on treestand. A good non-slip safety boot is important to

your personal safety. Be especially careful that boot laces

do not get hooked on the stand or any of its components

(tuck shoelaces into boots before climbing).

Never touch or move buckle while stand is in use.

INSPECTION AND MAINTENANCE SCHEDULE

BEFORE EACH USE PERFORM THE FOLLOWING:

• Inspect all webbing, rope, cord, and strap assemblies for

wear or damage.

• Inspect cables and/or cable ends for damage or kinking.

• Inspect all hardware and chain components for damage.

• Inspect for any structural damage to product. (If any exists

call RETI customer service.)

• Inspect all nut and bolt assemblies to be certain none are

loose.

• Inspect for any missing parts.

• Lubricate all pivot and slide together points with powder

graphite, petroleum jelly or silicone spray to prevent noise,

wear and rust.

• Inspect entire product for any rust, corrosion, cracks,

freezing, excessive heat or rotting damage that may eect

the safety of your product. Discard any questionable

product.

• Inspect entire product for any structural damage - pay close

attention to all weld locations. (Return to factory for repair or

discard product if any damage is found.)

• Using correct wrenches inspect all nut & bolt assembly

locations and snug up any that may be loose. Be careful not

to crush tubing when tightening!

• Inspect and check operation of all cables, cable ends, cord,

rope, webbing, and strap or chain assemblies. Replace with

factory new any item or assembly that shows signs of wear,

damage, kinking, or functions incorrectly.

• Inspect seat. Replace any seat with factory new that shows

signs of structural damage or wear.

• Inspect all hardware for wear or damage, also be sure you

have no missing parts.

• Never modify your stand in any way by making repairs,

replacing parts, or altering adding or attaching anything to it

except if explicitly authorized in writing by the manufacturer.

Check for parts online at www.HuntRiversEdge.com or call 800-450-EDGE (3343) M-F 8-5 5

Operator's Manual

Hang-On Stands

ASSEMBLY INSTRUCTIONS RE513

Tools needed – two 7/16" wrenches, two 1/2" wrenches

IMPORTANT ASSEMBLY TIP: Do not tighten any nut and bolt combi-

nations completely until all parts are assembled together! Finger

tighten plus one turn of a wrench only! This will temporarily hold the

lock nut on the bolt while helping alignment of all parts! After all parts

are assembled together, all nut & bolt combinations must be com-

pletely tightened.

1. Bolt the metal seat frame (C33) onto the seat post using the (2) provided

1/4-20 x 2-1/4" bolts, locknuts and (6) nylon washers. SEE FIGURES 1.

DO NOT tighten all nut & bolt assemblies completely!

2. Attach removable seat cushion to metal seat frame by sliding seat

frame into pocket. Wrap the Velcro seat straps or buckle straps

around seat frame and secure together. Snap the side release buckle

together for buckle style seats. Pull straps tight so seat is not loose.

3. Bolt cables onto platform using the (2) provided 5/16-18 x 1-1/2" bolts,

locknuts and steel washers. SEE FIGURE 2.You must now tighten all

nut & bolt assemblies. Be sure not to over tighten or crush tubing

when tightening!

NOTE: Using powder graphite lubricant during assembly of moving

parts will help eliminate noise during use!

FIGURE 1

1/4-20 x 2-1/4" bolts

nylon washers

locknuts

seat frame

seat post

platform cable

5/16-18 x 1-1/2" bolts

steel washers

locknut

FIGURE 2

Check for parts online at www.HuntRiversEdge.com or call 800-450-EDGE (3343) M-F 8-56

Operator's Manual

Hang-On Stands

ASSEMBLY INSTRUCTIONS RE552

Tools needed – two 7/16" wrenches, two 1/2" wrenches

IMPORTANT ASSEMBLY TIP: Do not tighten any nut and bolt combina-

tions completely until all parts are assembled together! Finger tighten

plus one turn of a wrench only! This will temporarily hold the lock nut on

the boltwhile helping alignmentof allparts!After allparts are assembled

together, all nut and bolt combinations must be completely tightened.

1. Attach the seat frame weldment (CXR15) to the seat post (CXR14) using

(2) provided 1/4-20 x 2-1/2”bolts, locknuts and (6 to 8) nylon washers.

SEE FIGURE 3. DO NOT tighten all nuts and bolts completely!

NOTE: You may need to place 2 nylon washers between seat post

upright and seat frame to take up necessary gap.

2. Attach cable (48212) ends to the platform (CXR12) using (2) provided

5/16-18 x 1-1/2” bolts, locknuts and steel washers. SEE FIGURE 4.

You must now tighten all nut & bolt assemblies securely. Be sure

not to over tighten or crush tubing when tightening!

NOTE: Using powder graphite lubricant during assembly of moving

parts will help eliminate noise during use!

3. If included, attach backpacking straps (48067) at desired location

on platform. Fold strap in half. Feed folded strap through platform

mesh. Feed the two loose ends of strap through folded loop and pull

tight forming a cinch knot. SEE FIGURES 5A AND 5B. Feed straps

through platform mesh and secure with provided tri-slide buckles.

SEE FIGURES 5C

4. Attach padded seat (48103) by feeding straps around the lower portion of

seat frame. Feed the long strap through both metal tri-slides that are sewn

to opposite side of strap. Wrap the long strap back around one tri-slide

and through the second tri-slide and pull tight. SEE FIGURE 6. Repeat

the same operation for the other seat strap. Adjust as needed to achieve

desirable seat height. Excess strap can be tucked away using provided

Velcro tabs under the seat.

5. Attach (2) provided 9" camo arm pads (48736) to upper portion of

seat frame weldment by wrapping around tubing and attaching

Velcro together.

FIGURE 6

FRONT VIEW OF

SEAT ASSEMBLY

pull to

tighten

FIGURE 5A FIGURE 5B

FIGURE 5C

platform cable

5/16-18 x 1-1/2" bolts

steel washers

locknuts

FIGURE 4

locknuts

nylon washers

(2 if needed)

1/4-20 x 2-1/2"

bolts

nylon washers

FIGURE 3

Check for parts online at www.HuntRiversEdge.com or call 800-450-EDGE (3343) M-F 8-5 7

Operator's Manual

Hang-On Stands

WARNING

Double check assembly steps to be certain you have

correctly assembled this product.

Practice installing, adjusting and using your treestand at

ground level prior to using it at elevated positions. Study

your new stand to become familiar with all of its features

and design. Doing so will conrm that the product is

manufactured, assembled and installed correctly.

Always wear the appropriate footwear when using a hang-

on treestand. A good non-slip safety boot is important to

your personal safety. Be especially careful that boot laces

do not get hooked on the stand or any of its components

(tuck shoelaces into boots before climbing).

Climbing aids (stick ladders, sectional ladders, steps, etc.)

must extend above the platform to allow the user to step

down onto the platform. Never step up to your stand from

a climbing aid. To ensure that you step down onto the

platform, the maximum recommended use height is ve

feet less than the height of the climbing aid being used.

Do Not twist strap when attaching. See setup and use

instructions for correct attachment.

Always climb tree onthe attachmentside ofthis treestand.

Visually inspect your connection to be assured you have

correctly attached stand to tree as per instructions and

diagrams.

The use of a lineman’s/climbing belt is required while

ascending, descending and installing a hang-on treestand

to stabilize the user with the tree.

Correct tightening and adjustments of chains, cables,

straps, etc. are critical to stable hang-on treestand

installation. All treestand contact points must be in

contact with the tree before you step onto your stand.

Platform must be folded up to remove stand! This allows

slack in strap for removal.

Never touch or move buckle while stand is in use.

If seat is removable, be certain it is securely attached

when in use.

Never stand on seat, it is designed for sitting only.

Some models include a footrest, which is designed as a

footrest only. Never stand on footrest! Always be fully

aware of foot placement.

WARNING

All users are responsible for ensuring strap is attached

to treestand properly and securely. Failure to do so may

result in serious injury or death. Read and understand

all instructions for proper installation procedure and

product warnings before use.

WARNING

Only use approved RETI parts. Failure to do so may result

in serious injury or death!

WARNING

It is critical to familiarize yourself with how the strap

attaches to the stand. Practice attaching the stand to the

tree several times at ground level before ascending up

the tree.

Check for parts online at www.HuntRiversEdge.com or call 800-450-EDGE (3343) M-F 8-58

Operator's Manual

Hang-On Stands

SETUP AND USE INSTRUCTIONS

RE513 & RE552

During installation and removal of a hang-on treestand, you must

always and properly use the included Full Body Harness (Fall Arrest

System) with climbing belt. Refer to the Full Body Harness and

climbing belt instructions included with this product for proper use.

You must always use the Full Body Harness while using this product.

1. At desired height, attach by following instructions - a,b,c,d,e,f.

NOTE: Stand should be attached to tree with platform folded in

an upright position!

a. Lengthen strap by pulling buckle away from strap - this will allow

strap to slide around buckle roller bar.

b. Take snap hook/buckle end and wrap around tree. Be sure the

strap is even and at the same level all the way around the tree. Also,

be sure there are no twists in the strap. Connect hook to opposite

side of stand by inserting through slot provided. Be absolutely sure

snap hook engages through slot of bracket and can not come o.

SEE FIGURE 7

c. Pull on excess end of strap rmly - snugging up stand to tree.

SEE FIGURE 8

NOTE: Platform must be folded up while doing this.

d. While platform is still folded up, push treestand in a downward

direction to further tighten strap. SEE FIGURE 9

e. Once securely attached, pivot the platform down.This lever-action

will snug stand up tight to tree to prevent any shifting. Redo as

necessary to accomplish a snug stand-to-tree t. All four contact

bars must be touching tree! SEE FIGURE 10

f. The tension on strap will not allow any slippage due to roller bar

tension of buckle. Proper installation should be checked prior to

stepping onto platform to ensure safety.

2. Before stepping down onto center of stand platform, be sure it is secured

properly and is tight against tree with all (4) contact bars touching tree!

3. Carefully step onto stand platform to be sure you have a solid feel

against tree and platform is level. Seat folds down for sitting and tips

back for standing.

4. RE552 ONLY. Attach backrest portion of seat to tree by wrapping

the long strap with buckle end around tree and snapping together

with opposite end. Adjust as needed.

NOTE: To remove stand, fold platform back up and pull on buckle hand

strap to release tension on roller bar.

TREE

FIGURE 7

FIGURE 8 FIGURE 9

FIGURE 10

excess end

of strap

platform

seat

Check for parts online at www.HuntRiversEdge.com or call 800-450-EDGE (3343) M-F 8-5 9

Operator's Manual

Hang-On Stands

THREADING THE FLOAT BUCKLE

Always check the condition of your Big Foot strap before use. If strap

becomes twisted or if you need to replace a worn or damaged strap,

make sure to follow these instruction to ensure proper assembly.

1. Hold oat buckle so warning tag faces upward. SEE FIGURE 11

2. Feed end tail of strap up through the bottom of the oat buckle on

the snap-hook side of the roller bar. SEE FIGURE 12

NOTE: Smooth side of end tail must face snap-hook.

3. Feed end tail over roller bar and down through oat buckle.

SEE FIGURE 13

4. Pull end tail away from oat buckle. SEE FIGURE 13

FIGURE 13

FIGURE 11

warning tag

oat buckle snap-hook

FIGURE 12

snap-hook

roller bar

end tail

of strap smooth side

WARNING

All users are responsible for ensuring strap is attached

to treestand properly and securely. Failure to do so may

result in serious injury or death. Read and understand

all instructions for proper installation procedure and

product warnings before use.

WARNING

Only use approved RETI parts. Failure to do so may result

in serious injury or death!

WARNING

It is critical to familiarize yourself with how the strap

attaches to the stand. Practice attaching the stand to the

tree several times at ground level before ascending up

the tree.

Check for parts online at www.HuntRiversEdge.com or call 800-450-EDGE (3343) M-F 8-510

Operator's Manual

Hang-On Stands

BIG FOOT™ TRAVELER

Model RE513

HANGON PARTS EXPLOSION RE513

KEY # PART # DESCRIPTION QT Y.

1 8655B BOLT 5/1618 X 13/4" HH BLK ZN 2

2 48210 CABLE 26" BLACK VINYL W/

BLACK ENDS

3 48152 BOLT 5/1618 X 11/2" HH BLK ZN 2

4 48250B BOLT 1/420 X 13/4" HH BLK ZN 2

5 WN516 WASHER 5/16" NYLON, BLK 6

6 WF516B WASHER 5/16" FLAT BLK ZN 8

7 48271B BOLT 1/420 X 21/4" HH BLK ZN 2

8 48752B NUT 1/420 FLANGE NYLOCK BLK

960G5NYB NUT 5/1618 FLANGE NYLOCK

BLK ZN

10 CB18 PLATFORM 1

11 C19 SEAT POST 1

12 C33 SEAT FRAME 1

ITEMS BELOW NOT SHOWN

 RE760 TREE STRAP ASSEMBLY 1

 10531 FULL BODY HARNESS FAS 1

 15599 CLIMBING BELT 1

 48101 SEAT PAD 1

 48800 DVD TREESTAND SAFETY 1

HANGON PARTS LIST RE513

Check for parts online at www.HuntRiversEdge.com or call 800-450-EDGE (3343) M-F 8-5 11

Operator's Manual

Hang-On Stands

HANGON PARTS EXPLOSION RE552

KEY # PART # DESCRIPTION QT Y.

1 1423B BOLT 5/1618 X 2 HHCS

GR5 BLK ZN

2 48153B BOLT 1/420 X 2 HHCS

GR5 BLK ZN

3 48212 CABLE 28" BROWN VINYL 2

4 48152 BOLT 5/1618 X 11/2 HHCS

GR5 BLK ZN

5 48270B BOLT 1/420 X 21/2 HHCS

GR5 BLK ZN

6 WF516B WASHER FLAT 5/16" STANDARD

BLACK ZN

7 WN516 WASHER, 5/16", BLACK NYLON 10

860G5NYB NUT 5/1618 NYLOCK BLACK 4

9 48752B NUT, FLANGED, NYLOCK, 1/420 4

10 CXR14 WELDMENT, FTS, SEAT POST

LOUNGER

11 CXR15 WELDMENT, SEAT FRAME,

LOUNGER

12 CXR12 WELDMENT, PLATFORM,

LOUNGER

ITEMS BELOW NOT SHOWN

 RE760 TREE STRAP ASSEMBLY 1

 10531 FULL BODY HARNESS FAS 1

 15599 CLIMBING BELT 1

 48103 SEAT W/ BACKREST, LOUNGER

HANGON

 48736 CAMO ARMREST PAD, 9" 2

 48067 KIT, BACKPACK STRAPS 1

 48800 DVD TREESTAND SAFETY 1

HANGON PARTS LIST RE552

BIG FOOT™ XL LOUNGER

MODEL RE552

*All weights, specications and features are approximate and are subject to change without notice. Due to continuous product improvements, product images may not be exact. Warning labels in some product images