Roberts SRCD970 User manual

SRCD970
Stereo CD Radio
Cassette Recorder
Please read this manual before use
ROBERTS
Sound for Generations

1. Tone control
2. Headphone socket
3. Tape/Radio/C Function
switch
4. Volume control
5. Telescopic aerial
6. C lid
7. C repeat button
8. C stop button
9. C play/pause button
10. C mix button
11. C track F Skip and B Skip
buttons
12. C compartment open button
13. FM stereo indicator
14. Waveband switch
15. Tuning scale
16. Tuning control
17. Liquid crystal display
18. Pause button
19. Stop/eject button
20. Fast forward button
21. Rewind button
22. Play button
23. Record button
24. Cassette door
1
2
3
4
5
6
7
8
9
10
11 12 14 15
16
13
17
18
19
20
21
22
23
24
Controls

If you need any further advice, please
call our Technical Helpline on
0181 758 0338 (Mon- ri)
General
o not allow this unit to be exposed to water or steam. o not leave the unit
where excessive heat could cause damage. It is recommended that the FM
band be used wherever possible as better results in terms of quality and
freedom from interference will usually be obtained than on the MW band.
Mains supply
The SRC 970 will operate from a supply of AC 230 volts, 50Hz only.
For your convenience this product is supplied with a plug which is fitted with
a fuse of the appropriate rating. If the plug supplied is not suitable for your
socket outlet, it should be removed by unscrewing the plug top, the terminal
screws, and removing the cable.
The correct style of plug to suit your household together with a correctly
rated fuse should be fitted.
IF IN OUBT - CONSULT A QUALIFIE ELECTRICIAN
IMPORTANT. DO NOT make any connection to the larger terminal which
is marked with the letter E or by the safety earth symbol or coloured
Green or Green-and-yellow.
The wires in the mains lead are coloured in accordance with the following
codes :-
BLUE - NEUTRAL BROWN - LIVE
As these colours may not correspond with the coloured markings identifying
the terminals in your plug, proceed as follows:
The wire coloured BLUE must be connected to the terminal marked N or
coloured BLACK.
The wire coloured BROWN must be connected to the terminal marked L or
coloured RE .
use
This apparatus must be protected by a 3A fuse (BS1362) in a 13A plug
(BS1363). If another type of plug is used a 5A fuse should be fitted in the
plug, adaptor or distribution board.
IF IN OUBT - CONSULT A QUALIFIE ELECTRICIAN.
Batteries
Remove the battery cover on the rear of the unit by pushing the catches in
the direction of the arrows. Insert eight IEC size LR20 batteries ( size) into
the compartment. Take care to ensure all batteries are inserted with the
correct polarity as shown inside the battery compartment. Replace the
battery cover.
Reduced power, distortion, and a 'stuttering' sound are all signs that the
batteries may need replacing.
We would recommend for economy, that the SRCD970 is used on the
mains whenever possible with battery operation for occasional or
stand-by use only
Automatic Mains/Battery switching
To change from battery to mains operation, simply plug the mains lead into
the mains input socket on the rear of the unit. The batteries will be
automatically disconnected. It does not matter which way round the plug is
inserted but make sure it is fully pushed home. The other end should be
plugged into a domestic supply socket.

Aerials
The telescopic aerial (5) located on the rear of the SRC 970 is for FM
reception. The telescopic aerial should be fully extended and angled for
optimum reception
There is a built in ferrite aerial for MW stations. Rotate the SRC 970 to the
position giving best reception.
Radio operation ( M)
Slide the Tape/Radio/C switch (3) to the "Radio" position. Slide the
waveband switch (14) to the FM Stereo position. Adjust the volume
control (4) until a hissing sound is heard. Rotate the tuning control (16) until
the desired station is received. If the station being received is in 'Stereo' the
stereo indicator (13) will illuminate. Adjust the volume control (4) and tone
control (1) to the required settings.
If the FM signal becomes weak or is accompanied by a high level of
background hiss, you may select 'MONO' mode by setting the waveband
switch (14) to the "FM" position. To switch off the radio, slide the Tape/
Radio/C switch (3) to the "Off/Tape" position.
Radio operation (MW)
Slide the Tape/Radio/C switch (3) to the "Radio" position". Slide the
waveband switch (13) to the MW position. Adjust the volume control (4)
until a hissing sound is heard. Rotate the tuning control (16) until the desired
station is received. Adjust the volume control (4) and tone control (1) to the
required settings. Rotate the SRC 970 to the position giving best reception.
To switch off the radio, slide the Tape/Radio/C switch (3) to the "Off/Tape"
position.

If you need any further advice, please
call our Technical Helpline on
0181 758 0338 (Mon- ri)
CD operation
Playing a disc
Press the open button (12) to open the C compartment. Carefully place
a disc onto the spindle in the C compartment, ensuring that the label is
facing upwards. Close the lid ensuring it latches shut. Slide the Tape/Radio/
C switch (3) to the "C " position. The Liquid crystal display (17) will light
up if the unit is connected to the mains supply. Press the C play/pause
button (9) to play the disc. Adjust the volume control (4) and tone control (1)
to the required settings. To switch off, slide the Tape/Radio/C switch (3)
to the "Off/Tape" position.
Pausing during CD play
Whilst the C is playing, press the C play/pause button (9) to pause play.
The disc will continue rotating, but play will stop and the pause symbol will
appear on the Liquid crystal display (17). To resume play, press the C
play/pause button (9) again. The pause symbol will disappear from the
Liquid crystal display.
Stopping CD play
To stop C play, press the stop button (8). The disc will stop rotating.
Track change function
Whilst the C is playing, press either the F Skip or B Skip buttons (11) to
change to the desired track. You can also change tracks when the player
is in stop mode. Change to the desired track using the F Skip or B Skip
buttons (11) and press the play/pause button (15) to commence play of the
selected track.
Repeat function
To repeat only one track, press the repeat button (7) until the Liquid crystal
display shows REPEAT 1.
To repeat all tracks on a disc, press the repeat button (7) until the Liquid
crystal display shows REPEAT.
To cancel the repeat function, press the repeat button (7) until the word
REPEAT 1 or REPEAT is removed from the Liquid crystal display.

Mixed play
When mixed play is selected the SRC 970 will play all the tracks on the disc
in random order. Press the mix button (10) until the word Mix appears in
the display. Press the play/pause button (9) to start the disc playing. The
SRC 970 will now play all tracks on the disc in random order.
Listening to cassette tapes
Slide the Tape/Radio/C switch (3) to the "Tape" position. Press the stop/
eject button (19) to open the cassette door (24). Insert a pre-recorded
cassette with the tape surface nearest to the cassette keys and the side with
the desired recording facing towards you. Close the cassette compartment.
epress the play button (22) and adjust the volume control (4) to suit your
personal taste. Use the fast forward (20) or rewind buttons (21) to locate a
specific part of the tape. If you wish to temporarily stop the playback
depress the pause button (18). When you are ready to resume playback
press the pause button a second time. When the end of tape is reached the
SRC 970 will automatically switch off.
Recording from the Radio
Slide the Tape/Radio/C switch (3) to the "Radio" position. Tune in to the
desired station. Adjust the volume control (4) to suit your requirements.
Insert a blank cassette with the tape surface nearest to the cassette keys.
epress the record button (23) to commence recording. The recording
level is set automatically and is not affected by the setting of the volume
control. When recording from the MW band a whistle may occur. To remove
the whistle slide the beat cut switch (25) on the rear of the SRC 970 to the
position giving best reception.

If you need any further advice, please
call our Technical Helpline on
0181 758 0338 (Mon- ri)
Recording from CD
Press the open button (12) to open the C compartment. Carefully place
a disc onto the spindle in the C compartment, ensuring that the label is
facing upwards. Close the lid ensuring it latches shut. Slide the Tape/Radio/
C switch (3) to the "C " position. Insert a blank cassette with the tape
surface nearest to the cassette keys. epress the pause (18) and record
(23) buttons. Select the required track using the track buttons (11). Press
the pause button (18) followed by the C play/pause button (9) to commence
recording.
Caution
If the Record button will not depress, do not force it. It is probably because
the cassette tabs have been broken to prevent accidental erasure of an
existing recording (see preventing accidental erasure).
Headphones
A 3.5mm socket (2) on the top of the SRC 970 is provided for use with
stereo headphones. Inserting a plug into this socket automatically mutes
the internal loudspeakers.

A
C60
Safety tab side A Safety tab side B
Preventing accidental erasure
To safeguard your recordings against accidental erasure, break off the
appropriate tab on the cassette as shown . There is one tab for each side
of the cassette. This will prevent the Record button from being pressed. To
restore the cassette to normal, seal the tab openings with a small piece of
self-adhesive tape.
Cleaning the Heads
The binder and oxide from magnetic tapes can accumulate on the pinch
roller (A) the capstan shaft (B) and also the heads (C and ). This will impair
the sound quality.
To clean these parts proceed as follows:-
1. Turn off the power to the unit.
2. Press the Stop/Eject button (19).
3. Press the Play button (22) and the heads will be clearly seen.
4. Clean the surfaces (A, B, C, ) with a lint free rag or cotton swab soaked
in alcohol. Press the stop/eject button as soon as cleaning is over.

If you need any further advice, please
call our Technical Helpline on
0181 758 0338 (Mon- ri)
Product Care
o not expose the SRC 970 to extremes of temperature. The product
should be kept in a warm environment free from dust and damp. For
external cleaning use only a soft, clean cloth. Use a damp cloth to clean the
plastic cabinet. A mild soap will help to remove grease or oil. Never use
strong detergents or spray cleaners, abrasive powders, thinners or solvents
on the machine, as these may cause damage the finish.
CD Player Maintenance
The player mechanism is fitted with self-lubricating bearings, and must not
be oiled or greased.
Cleaning compact discs
While C s do not scratch the way vinyl records do, they are not
indestructible. Although the music tracks on the disc are covered with a
protective layer, it is still advisable to treat the disc carefully. As long as you
always pick up discs by the edge, and put them back in their holders
immediately after use, cleaning will not normally be necessary. However,
should fingerprints, dust or dirt appear, you can wipe them off with a soft,
lint-free cloth. Wipe the disc in a straight line from centre to edge. If the disc
is heavily soiled use a commercially available C cleaner. etergent or
abrasive cleaning agents must never be used. Never write on the disc label
 this can cause irreparable damage to the disc.

The Company reserves the right to amend the specification without notice.
Disc player
Laser wavelength 780nM
Laser power 5mW max
Frequency response 20Hz-20kHz +2db -2dB
Radio
requency Coverage
FM 87.5 -108MHz
MW 530 - 1605kHz
Aerial System FM Telescopic aerial
MW Built-in Ferrite aerial
Specifications
Power Requirements
Mains AC 230 volts, 50Hz only
Batteries 8 x LR20 ( size)
(battery life approx. 25 hours)
General
Output Power 2 x 2W RMS
Loudspeakers 2 x 100mm dia 4ohms
Headphone socket 3.5mm stereo
Imported by:-
ROBERTS RADIO LIMITED
PO BOX 130
MEXBOROUGH
SOUTH YORKSHIRE
S64 8YT