Robertshaw 9701i User manual

Models 9701i, 9715iand 9720i
Quick Start Installation Manual
111-284D
Installation DOs and DON’Ts
DO
• Shut off all power to system before installing.
• Read entire manual before installing.
• Make sure that all wiring conforms to
national and local codes.
DO NOT
• Install on voltages greater than 30 VAC.
• Short jumper across terminals on the gas
valve or at the system control.
• Connect ground to any terminal in
this unit.
• Install on outside walls or in direct sunlight.
Select location for installation.
1
Open the case with a screwdriver. Place
in slot and gently pry forward at all four
locations.
2
Mark mounting hole locations on wall.
3
Drill 3/16” holes at marked locations on
wall. Insert plastic anchors into holes.
4
Align unit base over plastic anchors
embedded in wall and secure with the
screws provided.
5
Connect wiring between unit and
furnace. For Model 9701i(1H/1C
gas/electric furnace).
6
Cut
out
opening
a
b
1/2"
1-1/2"
1"
1
2
3
4
Mark mounting hole
locations on wall using
unit base as template.
Drill 3/16 holes
a
b
Press anchors into holes until flush.
Y1
R
C
E/W1
O B G
G
Y
R
W
C
Thermostat
C - 24VAC Common
R - 24VAC
Y1 - 1st stage cooling
E/W1- 1st stage heating
O - Not used
B - Not used
G - Fan
TERMINAL DESIGNATIONS
9701i
Equipment Wiring
Terminals
Please refer to furnace
installation manual for
proper terminations.
DELUXE
PROGRAMMABLE
THERMOSTATS
Remove 1/2” of insulation
from end of each wire

NOTE: For 9701i single stage heat
pump applications, place a jumper
between the E/W1 and Y1 terminals.
7
Connect wiring between unit and
furnace. For Model 9715i (2H/2C
gas/electric furnace applications).
8
Replace cover on thermostat.
Turn on power to unit and proceed
with programming per instructions on
the display or in the user’s manual.
11
Connect wiring between unit and
furnace. For Model 9720i (2H/2C
heat pump with furnace or strip heat).
9
To set your name and phone
number into the thermostat press
MENU, select INSTALLER
SETTINGS, and CONTACT
INFORMATION. The screen at the
bottom left should appear.
To enter your name press EDIT.
Use the UP or DOWN button to
scroll through the characters.
(DOWN gets you to the letters
faster.) After each letter press NEXT.
When you are done entering your
name, press ACCEPT.
Connect wiring between the thermo-
stat and the indoor sensor (9020i)
and the outdoor sensor (9025i), if
used. Use twisted pair wiring (22AWG
minimum) with a maximum length of
300 feet (or 100m).
10
Now enter your phone number.
Use the UP and DOWN arrow to
select the first number. Press NEXT.
When you have completed entering
your phone number, press ACCEPT.
The screen will return to the
INSTALLER SETTINGS. Finish
setting the thermostat for the
application.
Y1
R
C
E/W1
O B G
Thermostat
C - 24VAC Common
R - 24VAC
Y1 - 1st stage cooling
E/W1- 1st stage heating
W2- 2nd stage heating
Y2 - 2nd stage cooling
L - Not used
O - Not used
B - Not used
G - Fan
TERMINAL DESIGNATIONS
W2
Y2
L
C
R
Y1
Y2
W1
W2
G
O
B
9715i
Equipment Wiring
Terminals
Please refer to furnace
installation manual for
proper terminations.
Y1
R
C
E/W1
O B G
Thermostat
C - 24VAC Common
R - 24VAC
Y1 - 1st stage heating/cooling
E/W1 - Emergency heat strip
W2- 2nd stage heating
Y2 - 2nd stage cooling
L - System fault indicator
O - Cool active reversing valve
B - Heat active reversing valve
G - Fan
TERMINAL DESIGNATIONS
W2
Y2
C
R
Y1
Y2
E
W2
L
G
B
L
O
9720i
Equipment Wiring
Terminals
Please refer to heat
pump installation manual
for proper terminations
If terminal E is not supplied,
add jumper across E/W1
and W2 on the thermostat.
Controls Americas
515 South Promenade Avenue
Corona, CA 92879-1736
United States of America
Made in Mexico
www.about-i-series .com 111-284D
Set Your Name Set Your Phone Number
Y1
R
C
E/W1
O B G
G
Y1
R
C
B
O
Thermostat
Jumper Wire
C - 24VAC Common
R - 24VAC
Y1 - 1st stage cooling
E/W1- 1st stage heating
O - Reversing valve (cool)
B - Reversing valve (heat)
G - Fan
TERMINAL DESIGNATIONS
9701i
Equipment Wiring
Terminals
Please refer to heat
pump installation
manual for proper
terminations.
CONTACT INFORMATION
BACK EDIT ACCEPT NEXT
CONTACT INFORMATION
AIR EXPERTS
CONTACT INFORMATION
AIR EXPERTS
ACCEPT NEXT
1
ACCEPT NEXT
CONTACT INFORMATION
AIR EXPERTS
1-555-555-1212
1 2
13
Recycling Thermostat
If this thermostat REPLACES a thermostat that contains mercury,
DO NOT discard the old thermostat in the regular trash. Mercury
is harmful to humans and the environment. For this reason, do not
open, break, or crush the mercury cell. If mercury leaks from a
damaged cell, DO NOT touch or handle mercury with bare hands.
Use protective, non-absorbent gloves to place mercury into a
sealable container. Fill the container with sand or another
absorbent material and seal the container completely.
Return the mercury or mercury products, in a sealed container, to
Invensys Climate Controls or a local recycling center for proper
disposal. If you have any questions, call Robertshaw technical
support at 1-800-445-8299.
In U.S.:
Invensys Controls Americas
28C Leigh Fisher Blvd.
El Paso, TX 79906
Attn: Mercury Recycling Center
In Canada:
Invensys Controls Americas
3515 Laird Road - Unit #14
Mississauga, Ontario L5L 5Y7
Attn: Mercury Recycling Center