roblight Ara 5 User manual

User manual
Ara 5

This device has a built in high power phosphor converted blue led. The light source
is grouped in Risk Group 2.
Warning
Do not look into the light port when lit.
Beware of placing highly light absorbing material directly in front (Distance 0-1cm)
of the port or a fibre. The extremely high intensity will increase the temperature in
the material.
Using non RobLight harnesses in this light generator is at its own risk.
Ensure that the polyconnector is undamaged and clean before using the light gener-
ator in retrofit RobLight installations.
Beware that when the or a light generator is operated at max ambient temperature
the surface temperature can exceed 75°C.
The light generator is only tested with RobLight standard polyconnector end.
The warranty label is not to be broken under ANY circumstances. If broken the
warranty is terminated.
Product overview/unboxing
1 Ara 4
1 User manual
Installation instructions
Follow the installation instructions to ensure
• Safe operation
• Full functionality
• Stated expected lifetime
• Uninterrupted illumination
Warranty label
Risk group 2
CAUTION.
Possibly hazardous optical radiation emitted from this
product. Do not stare at operating lamp. May be harmful
to the eye.

General
Material Aluminium, POM and other
Dimensions (L x H x W) Ø29 x 44 x 76 mm
Weight (total) 60 g
Safety CE, RoHS, WEEE, F
Topology Serial connection
Environmental
Protection rating IP 20
Cooling Natural convection
Ambient temperature 0° to 45°C
Driver/electrical
Driver LED driver constant current
Supply voltage (mains) 100-240V 50/60Hz
Driver expected lifetime 50.000 hours (@TC = 65°C)
Total power consumption 2.4 W
LED current 700 ma DC (±5%)
Dimmer systems applicable Pot, PUSH (mains)
Light source
Applied LED Cree
LED expected lifetime >50.000 hours @Ta = 25°C
Typical CCT 3000K
Typical Ra (CRI1-8) 97+
Technical data

Surface mounting
Connect driver and
main power (100-
240V)
Mount the track ( se user manuel 9908
2147)
and place the product on the track.
Local dimming Ara 5 and 5+
Each head can be dimmed
indivdually by pressing the button on the
base of the fixture. Will change the state of the fixture. The fixtur can
cycle betwen 3 states : Max intensity » Memorrized intensity » Min inten-
sity.
By keeping the button pressed it will adjust the dimming level. Dimming
level is memorized when button is released, and set the fixture in me-
morized state.
The fixture will omly dim to the lowest possibel light output.
By application of the master dimmed at the dim to 0 as achieved.

Lens mounting
When adjusting the 48°/8° lens use the narrow end
of lens tool A (accessor)
Easily mount the lens by
screwing io into the fixture
Dont touch the lens surface.
Installing accessories
You can mount a film filter using filter clip A (accessories).
Dimension : Ø28*0.4 mm
To ensure the most durable solution only use filters from recognized suppliers. (Lee,
Rosco, etc)
Place the filter in the holder
and press the holder onto the
lens
NB. The film technology is not a du-
rable solution and will fade.

Accessories
Part name Description Ordering
Lens A 10° black
Lens A 10° grey
Lens A 10° white Spot 10 1148 0100
1148 0105
1148 0106
Lens A 20° black
Lens A 20° grey
Lens A 20° white Narrow 20 1148 0300
1148 0305
1148 0306
Lens A 30° black
Lens A 30° grey
Lens A 30° white Medium 30 1148 0500
1148 0505
1148 0506
Lens A 48°/8° black
Lens A 48°/8° grey
Lens A 48°/8° white Oval 48/8 1148 0400
1148 0405
1148 0406
Lens tool A For mounting/removing lenses 1148 0007
Filter clip A black Mounting ring for colour filters 1148 0006
Driver set 4A 15W
15W 24V. Plug-and-play LED
driver
1-6 connections
1-10 V dimming
1148 0008
Driver set 4A 25W
25W 24V. Plug-and-play LED
driver
1-9 connections
1-10 V dimming
1148 0010
Driver set 4A 48W
48W 24V. Plug-and-play LED
driver
1-9 connections
1-10 V dimming
1148 0011
Filter Colour filter
Ø28*0.4 mm On request
Barn doors Ara black 1148 8012
Ara snoot 50 mm black 1148 8016

Troubleshooting
The cooling for this device is dependant that the metal surface is clean and free
from dust. The product can be cleaned with a soft brush or low pressure cleaned
and dry compressed air. If a vacuum cleaner is applied arrangements to remove
static electricity must be done.
The lens can be changed as shown in this manual. Take care not to damage or soil
the lenses when handling/cleaning. Take care not to touch the LED when the prod-
uct is open.
This product is not supposed to be otherwise serviced, if it is used as recommend-
ed.
If the product isn’t performing as specified, use the troubleshooting guide. If you
need further assistance please contact our office.
If needed the Led module can be interchanged by a trained technician.
Maintenance, spare parts and repairs
If problems are not solved using this guide, please contact RobLight A/S.
Problem Trace the problem Solution
No light
Check the power Connect the power cord properly/ Turn
on the device
Check the tempera-
ture.
Check it is installed according to the
instructions.
Check the dimming Unplug. Unplug the dimmer system
from the driver. Turn on the power.
Light switches
on and off
Check the operating
conditions of the
light generator
Check it is installed according to the
instructions.
Check active cool-
ing system.
Remove dirt and dust from light gene-
rator.

Application notes
The data we have stated are based on the expected lifetime of the key components
at the temperatures where the suppliers have performed their standardized tests.
All the data is for clean environment.
The product is designed to run at max. ambient, but the longest usable operation is
at lower temperatures.
If used using drivers and/or wiring not supplied by RobLight the warranty will be
terminated.
When using drivers not supplied by RobLight be aware of fluctuations in the current
supply as ripple and on/off current can be excessive for many standard CC drivers.
This product is a constant current device. Higher current than the stated will dam-
age the product.
The product is not designed to run without a lens.
This system is an electronic device and therefore will not work forever.
The light output and light tone can change during the lifespan of the product.
The most important factor influencing the practical lifetime is the temperature of
the surrounding air.
RobLight accepts no responsibility for possible errors in catalogues, brochures and other printed material.
RobLight reserves the right to alter or discontinue its products without notice. © 2019 RobLight A/S
RobLight A/S, Nordhavnsvej 1A, DK-9900 Frederikshavn
T: [phone], E: [e-mail]
www.rob-light.com
99082116, 17-06-2021, Rev. 1.1
CLEAN AIR
KEEP COOL