Rocky Mountain COLORADO User manual

Rocky Mountain Saunas
INSTRUCTIONS MANUAL
ROCKY MOUNTAIN SAUNAS INC.
7450-M W. 52ND AVE. PMB 123
1-888-358-1270
www.rockymountainsaunas.com
COPYRIGHT 2015 ROCKY MOUNTAIN SAUNAS INC. ALL RIGHTS RESERVED
i

ROCKY MOUNTAIN SAUNAS INC.
7450-M W. 52ND AVE. PMB 123
1-888-358-1270
www.rockymountainsaunas.com
COPYRIGHT 2015 ROCKY MOUNTAIN SAUNAS INC. ALL RIGHTS RESERVED
1
2
TABLE OF CONTENTS
INSTALLATION
ELECTRICAL REQUIREMENTS 3
UNPACKING YOUR SAUNA 5
COLORADO AND DURANGO INSTRUCTIONS 6-9
RIO GRANDE INSTRUCTIONS 10-13
BIG BEAR INSTRUCTIONS 14-17
HOW TO USE
CONTROL PANEL INSTRUCTIONS 18
FREQUENTLY ASKED QUESTIONS 19
DISCLAIMER 20
WARRANTY AND RETURN POLICY INFORMATION 21
SAFETY CERTIFICATIONS 22
Note:
The electric cord extends out from the center of the roof cap. The cord is approximately 9ft long. It is recommended that
the location of the outlet you are installing is accessible without moving the sauna.
Dedicated circuit requires that no other appliance should share outlet/circuit with sauna. Failure to comply with this
requirement may cause electrical interruption and diminished sauna performance.
It is recommended that a qualified electrician install your dedicated electrical wiring for proper sauna function and to avoid
any potential electrical hazards.

ROCKY MOUNTAIN SAUNAS INC.
7450-M W. 52ND AVE. PMB 123
1-888-358-1270
www.rockymountainsaunas.com
COPYRIGHT 2015 ROCKY MOUNTAIN SAUNAS INC. ALL RIGHTS RESERVED
1
3
ELECTRICAL REQUIREMENTS
Colorado: 110-120volts/15amp dedicated circuit/outlet
NEMA 5-15R(required) NEMA 5-15P(included)
8 Heaters 1600-watts
Durango/Rio Grande: 110-120volts/20amp dedicated circuit/outlet
NEMA 5-20R(required) NEMA 5-20P(included)
9 Heaters 2150-watts
Big Bear: 220-240volts/20amp dedicated circuit/outlet
NEMA 6-20R(required) NEMA 6-20P(included)
15 Heaters 2850-watts
WARNING:

ROCKY MOUNTAIN SAUNAS INC.
7450-M W. 52ND AVE. PMB 123
1-888-358-1270
www.rockymountainsaunas.com
COPYRIGHT 2015 ROCKY MOUNTAIN SAUNAS INC. ALL RIGHTS RESERVED
1
4
1) No plumbing or plumbing fixtures should be placed in the sauna.
2) Keep all liquids away from the heating panels
3) Install sauna on a completely level surface.
4) Flammable objects and corrosive chemical substances should be kept far away from the sauna.
Part A: Installation
Unpacking your Sauna
Please identify the 3 boxes (A/B/C) that arrived in your shipment. Place boxes in an open area. All 3 boxes are
labeled with the contents inside. It is recommended that a minimum of 2 people be present for unpacking and
assembly. Lay boxes flat on the ground with lettering facing up. Please make sure the area is clear of debris. Open
the boxes from smallest to largest to make for light, fast work.
The following steps will be divided into 3 sections.
First, we will start with the Colorado/Durango, next will be the Rio Grande and finally the Big Bear Sauna.
The tools required for assembly are a Phillips-Head Screwdriver (optional tools: Rubber mallet & small step ladder).
Note: All panels all labeled with white stickers. Please follow instructions carefully. If you should have any
questions, please do not hesitate to contact us at
1-888-358-1270 or info@rockymountainsaunas.com
Colorado & Durango

ROCKY MOUNTAIN SAUNAS INC.
7450-M W. 52ND AVE. PMB 123
1-888-358-1270
www.rockymountainsaunas.com
COPYRIGHT 2015 ROCKY MOUNTAIN SAUNAS INC. ALL RIGHTS RESERVED
1
5
Colorado Durango
Step 1: Open Box C (Floor panel/Roof panel/Bench panel/Accessories box). Lay the floor panel
at your desired location. The floor heater is towards the front of the sauna.
Step 2: Open Box A (Front panel/Back panel). Install the Back panel first by sliding the panel
onto the metal brackets on the floor panel. Next install the Front panel by the same method
used for the Back panel. Please remove plastic wrap from Front panel but be careful so that the
glass door does not swing open. At this point, one person should secure both Front and Back
panels by holding them.
Moving Your Sauna after Assembly- RMS strongly recommends that you place sliders or ‘EZ Moves’
(Lowe’s or Home Depot) under the furniture feet or the perimeter corners of the Base Platform of the
Colorado 2 person sauna to allow for easy sliding of the sauna into its permanent location after
assembly. Place the EZ moves under the corners prior to beginning assembly. (On the Durango, Rio
Grande and Big Bear models, you may want to use a few mores ‘sliders’. Place sliders under the corners and
under the outside perimeter of the base platform.)
IMPORTANT NOTE: WHEN MOVING THE ASSEMBLED SAUNA:
1. DO NOT PUSH ON THE CABINET ITSELF AS YOU MAY “RACK” OR DAMAGE SAUNA !!
2. ALWAYS PUSH ON THE BASE PLATFORM TO MOVE SAUNA !!
3. SLIDERS MAY BE LEFT IN PLACE FOR EASING MOVING TO FACILITATE DUSTING, VACUUMING, ETC.

ROCKY MOUNTAIN SAUNAS INC.
7450-M W. 52ND AVE. PMB 123
1-888-358-1270
www.rockymountainsaunas.com
COPYRIGHT 2015 ROCKY MOUNTAIN SAUNAS INC. ALL RIGHTS RESERVED
1
6
Step 3: Open Box B (Right Panel/Left Panel). Install Right and Left Panels by lining up the panels
to the Front and Back. Right Panel means Right facing the sauna Please semi-tighten installation
bolts (located in accessories box).
Step 4: Install Bench Support panel (located in Box C). Please make all 4 electrical connections to
the Back panel.

ROCKY MOUNTAIN SAUNAS INC.
7450-M W. 52ND AVE. PMB 123
1-888-358-1270
www.rockymountainsaunas.com
COPYRIGHT 2015 ROCKY MOUNTAIN SAUNAS INC. ALL RIGHTS RESERVED
1
7
Step 5: Install Bench by guiding it between the Right and Left panels. There are 2 small pieces of
wood that may be used to prevent the back of the bench from sliding upward when user sits on
front of bench. They can be screwed to back wall directly above the bench. The pieces of wood
are included in the accessories box. When all 4 panels and the bench seat are securely in place,
please tighten all installation bolts.
Step 6: Install Roof panel. Guide the roof panel over the sauna and secure into position. Please
feed all the electrical connections that are on the Front/Back/Right/Left panels through the
holes in the roof panel.
Step 7: Once Roof Panel is securely in place, proceed up top to make all electrical connections.
Please note that there are 3 white ribbon connections (2pin-temp sensor/3pin-chromo/8pin-
power). Match the male/female black electrical cord heater connections. There are 2 in the front
and 2 in the back

ROCKY MOUNTAIN SAUNAS INC.
7450-M W. 52ND AVE. PMB 123
1-888-358-1270
www.rockymountainsaunas.com
COPYRIGHT 2015 ROCKY MOUNTAIN SAUNAS INC. ALL RIGHTS RESERVED
1
8
Step 8: Install Top Cover. Feed the main power cord through the hole in the dust cover.
Step 9: Install Cup Holder(s), Magazine Rack, Towel Holder. These items may be installed in any
location that you desire. Mount Air Purifier to Back panel by using a wood screw (just like
hanging a picture). When installing the ionizer, cup holders, towel rack, etc., it is a good idea to
predrill a small hole prior to actually mounting the accessory. This will help to prevent any minor
splitting or chipping of the wood.
Step 10: Install Door Handle. If you have purchased the LCD Upgrade then you may connect it to
the 12volt Cig-adapter located on the ceiling, if not then cover the adapter with the wood knob
provided in your packaging.
Step 11: Once Installation is complete plug in sauna. Please make sure to read the “How to Use
Instructions” at the end of this booklet.

ROCKY MOUNTAIN SAUNAS INC.
7450-M W. 52ND AVE. PMB 123
1-888-358-1270
www.rockymountainsaunas.com
COPYRIGHT 2015 ROCKY MOUNTAIN SAUNAS INC. ALL RIGHTS RESERVED
1
9
Rio Grande
Rio Grande
Step 1: Open Box C (Floor panel/Roof panel/Bench panel/Accessories box). Lay the floor panel
at your desired location. The floor heater is towards the front of the sauna.
Moving Your Sauna after Assembly- RMS strongly recommends that you place sliders or ‘EZ Moves’
(Lowe’s or Home Depot) under the furniture feet or the perimeter corners of the Base Platform of the
Colorado 2person Sauna to allow for easy sliding of the sauna into its permanent location after
assembly. Place the EZ moves under the corners prior to beginning assembly. (On the Durango, Rio
Grande and Big Bear models, you may want to use a few mores ‘sliders’. Place sliders under the corners and
under the outside perimeter of the base platform.)
IMPORTANT NOTE: WHEN MOVING THE ASSEMBLED SAUNA:
4. DO NOT PUSH ON THE CABINET ITSELF AS YOU MAY “RACK” OR DAMAGE SAUNA !!
5. ALWAYS PUSH ON THE BASE PLATFORM TO MOVE SAUNA !!
6. SLIDERS MAY BE LEFT IN PLACE FOR EASING MOVING TO FACILITATE DUSTING, VACUUMING, ETC.

ROCKY MOUNTAIN SAUNAS INC.
7450-M W. 52ND AVE. PMB 123
1-888-358-1270
www.rockymountainsaunas.com
COPYRIGHT 2015 ROCKY MOUNTAIN SAUNAS INC. ALL RIGHTS RESERVED
1
10
Step 2: Open Box A (Front panel/Right Front/Left Front). Install the Front panel first by sliding
the panel onto the metal brackets on the floor panel. Next install the Left Front panel by raising
it above Front panel and guiding it down into the metal brackets. Next install Right Front panel
by same method as Left Front panel. Please remove plastic wrap from Front panel but be careful
so that the glass door does not swing open. At this point, one person should secure both the
panels by holding them.
Step 3: Open Box B (Right Back panel/Left back Panel). Install Right back Panel by sliding panel
onto metal brackets on Floor panel. Semi-tighten Right Back panel to Right Front panel using
Installation bolts (accessories box). Install Left back panel to Right back panel and Left Front
panel (note there are no metal brackets on this side of the floor panel) Semi-tighten using
installation bolts.
Step 4: Install Bench Support panels (located in Box C). Please make all electrical connections to
the Back panel. Install Bench panels (3 pieces located in Box C). Once all panels and seats are
securely in place fully tighten all bolts.

ROCKY MOUNTAIN SAUNAS INC.
7450-M W. 52ND AVE. PMB 123
1-888-358-1270
www.rockymountainsaunas.com
COPYRIGHT 2015 ROCKY MOUNTAIN SAUNAS INC. ALL RIGHTS RESERVED
1
11
Step 5: Install Roof panel (located in Box C). Guide the roof panel over the sauna and secure into
position. Please feed all the electrical connections that are on the Front/Back/Right/Left panels
through the holes in the roof panel. After cables are through, use short anchoring bolts (2) in
each corner of roof cap to secure roof in place.
Step 6: Once Roof Panel is securely in place, proceed up top to make all electrical connections.
Please note that there are 3 white ribbon connections (2pin-temp sensor/3pin-chromo/8pin-
power). Match the male/female black electrical cord heater connections.
Step 7: Install Top Cover. Feed the main power cord through the hole in the dust cover. Optional
to secure dust cover with screws provided.

ROCKY MOUNTAIN SAUNAS INC.
7450-M W. 52ND AVE. PMB 123
1-888-358-1270
www.rockymountainsaunas.com
COPYRIGHT 2015 ROCKY MOUNTAIN SAUNAS INC. ALL RIGHTS RESERVED
1
12
Step 8: Install Cup Holder(s), Magazine Rack, Towel Holder. These items may be installed in any
location that you desire. Mount Air Purifier to Back panel by using a wood screw (just like
hanging a picture).
Step 9: Install Door Handle. If you have purchased the LCD Upgrade then you may connect it to
the 12volt Cig-adapter located on the ceiling, if not then cover the adapter with the wood knob
provided in your packaging.
Step 10: Once Installation is complete plug in sauna. Please make sure to read the “How to Use
Instructions” at the end of this booklet.

ROCKY MOUNTAIN SAUNAS INC.
7450-M W. 52ND AVE. PMB 123
1-888-358-1270
www.rockymountainsaunas.com
COPYRIGHT 2015 ROCKY MOUNTAIN SAUNAS INC. ALL RIGHTS RESERVED
1
13
Big Bear
Big Bear
Step 1: Open Box C (Floor panel/Roof panel/Bench panel/Accessories box). Lay the floor panel
at your desired location. The floor heater is towards the front of the sauna.
Step 2: Open Box A (Front panel/Back panel). Install the Back panel first by sliding the panel
onto the metal brackets on the floor panel. Next install the Front panel by the same method
used for the Back panel. Please remove plastic wrap from Front panel but be careful so that the
Moving Your Sauna after Assembly- RMS strongly recommends that you place sliders or ‘EZ Moves’
(Lowe’s or Home Depot) under the furniture feet or the perimeter corners of the Base Platform of the
Colorado 2 person Sauna to allow for easy sliding of the sauna into its permanent location after
assembly. Place the EZ moves under the corners prior to beginning assembly. (On the Durango, Rio
Grande and Big Bear models, you may want to use a few mores ‘sliders’. Place sliders under the corners and
under the outside perimeter of the base platform.)
IMPORTANT NOTE: WHEN MOVING THE ASSEMBLED SAUNA:
7. DO NOT PUSH ON THE CABINET ITSELF AS YOU MAY “RACK” OR DAMAGE SAUNA !!
8. ALWAYS PUSH ON THE BASE PLATFORM TO MOVE SAUNA !!
9. SLIDERS MAY BE LEFT IN PLACE FOR EASING MOVING TO FACILITATE DUSTING, VACUUMING, ETC.

ROCKY MOUNTAIN SAUNAS INC.
7450-M W. 52ND AVE. PMB 123
1-888-358-1270
www.rockymountainsaunas.com
COPYRIGHT 2015 ROCKY MOUNTAIN SAUNAS INC. ALL RIGHTS RESERVED
1
14
glass door does not swing open. At this point, one person should secure both Front and Back
panels by holding them.
Step 3: Open Box B (Right Panel/Left Panel). Install Left Panel by lining up the panel to the Front
and Back. Semi-tighten Left panel to Front and Back using Installation bolts (accessories box).
Step 4: Install Bench Support panels (located in Box C). This step should be completed prior to
installation of Right Panel. Make all electrical connections and install Bench panels (except for
the Right Bench Panel). You will need to complete step 5 first then make the Right side electrical
connections.

ROCKY MOUNTAIN SAUNAS INC.
7450-M W. 52ND AVE. PMB 123
1-888-358-1270
www.rockymountainsaunas.com
COPYRIGHT 2015 ROCKY MOUNTAIN SAUNAS INC. ALL RIGHTS RESERVED
1
15
Step 5: Install Right panel to Front and Back panels using Installation Bolts. Semi-tighten bolts.
Once all panels are fully secure tighten all bolts. Next, enter sauna and make final electrical
connections to the Right panel you just installed. Finally, Install the Right Bench.
Step 6: Install Roof panel. Guide the roof panel over the sauna and secure into position. Please
feed all the electrical connections that are on the Front/Back/Right/Left panels through the
holes in the roof panel.
Step 7: Once Roof Panel is securely in place, proceed up top to make all electrical connections.
Please note that there are 3 white ribbon connections (2pin-temp sensor/3pin-chromo/8pin-
power). Match the male/female black electrical cord heater connections.

ROCKY MOUNTAIN SAUNAS INC.
7450-M W. 52ND AVE. PMB 123
1-888-358-1270
www.rockymountainsaunas.com
COPYRIGHT 2015 ROCKY MOUNTAIN SAUNAS INC. ALL RIGHTS RESERVED
1
16
Step 8: Install Top Cover. Feed the main power cord through the hole in the dust cover and place
cover on roof panel. Optional to secure dust cover with screws provided.
Step 9: Install Cup Holder(s), Magazine Rack, Towel Holder. These items may be installed in any
location that you desire. Mount Air Purifier to Back panel by using a wood screw (just like
hanging a picture).
Step 10: Install Door Handle. If you have purchased the LCD Upgrade then you may connect it to
the 12volt Cig-adapter located on the ceiling, if not then cover the adapter with the wood knob
provided in your packaging.

ROCKY MOUNTAIN SAUNAS INC.
7450-M W. 52ND AVE. PMB 123
1-888-358-1270
www.rockymountainsaunas.com
COPYRIGHT 2015 ROCKY MOUNTAIN SAUNAS INC. ALL RIGHTS RESERVED
1
17
Step 11: Once Installation is complete plug in sauna. Please make sure to read the “How to Use
Instructions” at the end of this booklet.
2016 Models/New Door Handle Instructions:
*Follow picture instructions left to right, top to bottom of page.

ROCKY MOUNTAIN SAUNAS INC.
7450-M W. 52ND AVE. PMB 123
1-888-358-1270
www.rockymountainsaunas.com
COPYRIGHT 2015 ROCKY MOUNTAIN SAUNAS INC. ALL RIGHTS RESERVED
1
18
2016 Models/New Door Handle Instructions:
*Follow picture instructions left to right, top to bottom of page.

ROCKY MOUNTAIN SAUNAS INC.
7450-M W. 52ND AVE. PMB 123
1-888-358-1270
www.rockymountainsaunas.com
COPYRIGHT 2015 ROCKY MOUNTAIN SAUNAS INC. ALL RIGHTS RESERVED
1
19
2016 Models/New Door Handle Instructions:
*Follow picture instructions left to right, top to bottom of page.

ROCKY MOUNTAIN SAUNAS INC.
7450-M W. 52ND AVE. PMB 123
1-888-358-1270
www.rockymountainsaunas.com
COPYRIGHT 2015 ROCKY MOUNTAIN SAUNAS INC. ALL RIGHTS RESERVED
1
20
**Door handle may feel warm while sauna is in use**
This manual suits for next models
3
Table of contents
Popular Plumbing Product manuals by other brands

Kessel
Kessel Megastop installation instructions

Hans Grohe
Hans Grohe 94139 7 Series Assembly instructions

Sentiotec
Sentiotec Concept R CP-RC-AF Instructions for installation and use

American Standard
American Standard Jasmine Amarilis 3630 SERIES installation instructions

BELLOSTA
BELLOSTA noel 1501/A Installation instruction

Franke
Franke BRP390 Installation and operating instructions

Omnires
Omnires Y1231CR Installation and Maintenance

Kalia
Kalia BELLINO BF1057 installation instructions

Belvedere
Belvedere 8400 BACKWASH SHAMPOO BOWL quick start guide

RIHO
RIHO Scandic Soft Q400 installation instructions

Halsey Taylor
Halsey Taylor SCWT8A-CB-Q owner's manual

Blue Lagoon
Blue Lagoon UV-C Series Tech manual