Rolls MX34c LiveMix User manual

Quick Start Guide
ROLLS CORPORATION
SALT LAKE CITY, UTAH
8/19
Thank you for purchasing the new MX34c LiveMix - two channel microphone mixer.
Although having many uses, this little mixer was originally designed with the video
camera operator in mind. Easy-access microphone Level and Pan controls, and smart
Input/Output jack placement make the MX34c ideal for the live recording enthusiast.
Two 9 volt alkaline batteries ensure adequate signal strength as well as phantom
power for your favorite condenser microphone.
What's in the box?
1 - Made in USA MX34c
1 - 15V power supply PN PS27s
1 - This owners manual
MX34c LiveMix
POWER
15 VDC
STEREO
OUT
AUX
IN
+
-
BATTERIES
9V x 2
LiveMix
Two Channel Stereo
Microphone Mixer/
Headset Mixer
MX34c
CHANNEL 1 CHANNEL 2
INPUTS
www.rolls.com
OUTPUT LEVEL
MIC
LINE
OFF=UP
ON=DOWN
PHANTOM POWER
Input Impedance: mic - 600 Ohms or greater XLR
aux - 47K stereo 3.5mm
Output Impedance: 50 Ohms
THD + Noise: .02%
S/N Ratio: 110 dB
Frequency Response: 20 Hz - 30 kHz (+0 / -1 dB)
Max Output Level: + 14 dB
Max Input Level: +20 dB
Max Gain: +70 dB
Batteries: 2 X 9V Alkaline (not included)
Current Draw: 30 mA
Phantom Power: +18 VDC
Input Connectors: 2 Female XLR, 1/8” (3.5mm)
DC Power Jack: (5.5 X 2.1 mm tip negative)
Output connectors: 3.5mm stereo main out
3.5mm Headphone
Size: 6.3”w x 3.7”d x 1.4” h
Weight: 1 lbs.
NOTE: ON CONNECTING A WIRELESS MIC TO THE AUX INPUT
DO NOT CONNECT A MONO PLUG TO THE AUX
IN OR STEREO OUTPUT. DOING SO WILL
RESULT IN SIGNAL LOSS OR DAMAGE TO THE
MX34c.
If you need to connect a MONO signal (like the
output of a wireless microphone) to the AUX IN
of the MX34c, you will need to make or purchase a
MONO TO STEREO cable.Shown here is a diagram
of this cable’s wiring.
MONO PLUGTIP RING SLEEVE
STEREO PLUG
Tip and Ring are wired together,
then connected to the Tip of the
Mono Plug.

c
HEADSET
MIC
1/8”
POWER
15 VDC
STEREO
OUT
AUX
IN
+
-
BATTERIES
9V x 2
LiveMix
Two Channel Stereo
Microphone Mixer/
Headset Mixer
MX34c
CHANNEL 1 CHANNEL 2
INPUTS
www.rolls.com
OUTPUT LEVEL
MIC
LINE
OFF=UP
ON=DOWN
PHANTOM POWER
15 VDC jack: For connection to the Rolls
PS27s 15 VDC power supply.
1 - 2: XLR balanced inputs for connection to
any standard dynamic or condenser micro-
phone. The input circuitry has a very wide
input range and can accommodate almost
any (mic to line) level signal.
STEREO OUT: Tip-Ring-
Sleeve stereo 1/8”(3.5mm)
jack for connection to a
camera or other stereo
input.
AUX IN: Tip-Ring-Sleeve stereo 1/8”
(3.5mm) jack for connecting to another
line-level stereo signal source.
MIC/LINE OUTPUT LEVEL: Button for switching the
stereo output level to MIC or LINE.
BATTERY INSTALLATION: To replace the 9 V alkaline
batteries, rst carefully press in and up on the door
to release the battery compartment. It then slides
out and you can replace the battery. Remember to
replace both batteries at the same time.
PHANTOM POWER: Switch to activate
phantom power for the input XLR’s.
Adjusts the amount
of signal from
the Headphone
Output.
PAN: Adjusts the relative
level of signal from the
channel to the Right/Left
Output.
OUTPUT: 1/8” (3.5mm) jack containing
the stereo Headphone Output signal.
POWER: Button applies power to the MX34c.
MIC1 and MIC2
LEVEL: Adjusts the amount of signal
of the indicated Microphone channel.
MIC 1 headset mic input. Any
headset mic can be used. The
required power is set to the mic
with the TRS cable.