Room boost HT2018001 User manual

Package Contents
1.Booster
2.Outside Panel Antenna with RG58 Cables(50 or 45 feet)
3.Power Adapter
4.Inside Whip Antenna
5.Mounng Screw Kit
6.3M double-sided glue
Quick Install Diagram
Find the
Strongest Signal
Outside
Antenna Installaon
Connect
Cables to Booster
Inside
Antenna Installaon
Connect
Power Supply
1
Room boost
Room boost
Room boost 700 MHz
4G LTE AT&T T-Mobile
Booster instrucon
Signal booster
Model: HT2018001

1.Find the Strongest Signal
2
Take your cell phone and walk around the house where you
need to install the Booster. You can find the locaon of the
strongest signal, and the outdoor antenna is best installed in
this locaon.
2.Outside Antenna Installaon
The outdoor antenna must be installed on the roof or height.
There is no shelter around the antenna. The antenna is fixed
on the pole. The antenna can rotate around the pole, so that
the antenna can be beer aligned with the direcon of the
cell tower and receive the strongest signal.

3
3.Connect Cables to Booster
Now put the indoor antenna on the Booster, pay aenon to the
relave posion between the indoor antenna and the outdoor
antenna, we must meet the requirements of the following picture.
If the space is limited, try to make the outdoor antenna higher,
otherwise the Booster will not work properly.
4.Inside Antenna Installaon
Next, the cable of the outdoor antenna is introduced into the
room. Noce that the cable does not have a bending of less than
60 degrees so as not to damage the cable to affect the
performance. Connect the cable to the outside joint of the
booster
>13 feet
separation
>19 feet
separation
Outside Antenna
Power Adapter
Intside Antenna
Room boost
Booster is fixed
to the desktop or
wall by 3M
double-sided
glue, so it can not
be moved when
working.

4
5.Connect Power Supply
Finally, the power is turned on, if your mobile phone signal
has been enhanced, Congratulaons, you succeed. If you are
not very sasfied with the intensity, then adjust the angle of
the outdoor antenna unl you feel the cell phone signal is
sasfied.
*WARNING:
1.The booster is designed for use in indoor ONLY.
2.Do NOT cover the booster body with anything. This prevents if
from cooling down. If the product becomes overheated, it
will automacally shut off or cause permanent damage.
3.Use only the power supply provided by Room boost. Any other
non-approved products by Room boost of self-made power
cables may damage the booster.
4.Unauthorized antennas, cables, and/or coupling devices are prohibited
by FCC regulaons. Please contact FCC for details: 1-888-CALL-FCC.
This is a CONSUMER device
BEFORE USE MUST REGISTER THIS DEVICE,you with your wireless provider and have your provider's consent .Most
wireless provider consent to the use of signal boosters .Some providers may not consent to the use of this device on their
network .If you are unsure ,contact your provider.
You operate this device with approved antenna and cables as specified by the manufacturer .Antennas be MUST MUST
installed at least 20cm (8inches) from any person.
You cease operating this device immediately if requested by the FCC or a licensed wireless service provider.MUST
E911 location information may not be provided or may be inaccurate for calls served by using this device.WARNING.
This device may be operated in a fixed location for in-building use.ONLY

Antenna Kitting Information
5
Component Prod No.
Descripon
Gain/Loss
Notes
698~787M
HZ
824~894
MHz
1850~1990
MHz
1700MHz\2100
MHz
Outside Cable
HT240 45Feet 2.9dB 3.3dB 4.8dB 4.8dB\5.2dB
Outside Cable
HTG58 45Feet 6.9dB 7.5 dB
11.7 dB 11.1dB \12.3dB
Outside Cable
HT400- 75Feet 4.2dB 4.4dB 6.1dB 5.8dB\6.5dB
Inside Cable HTG6 75Feet 3.5dB 4.1dB 6.2dB 5.5dB\6.9dB
Inside Cable HTG6 45Feet 2.1dB 2.4 dB
3.7dB 3.3 dB\4.1dB
Inside Cable HT240 90Feet 5.8dB 6.7 dB
9.7 dB 9.6dB\10.2dB
Inside Cable HT240 75Feet 4.8dB 5.6dB 8.2dB 8.2dB\8.6 dB
Inside Cable HT240 60Feet 3.9dB 4.5dB 6.6dB 6.5 dB\6.7dB
Inside Cable HT240 45Feet 2.9dB 3.3dB 4.87dB 4.8dB\5.2dB
Inside Cable HT400- 30Feet 1.9dB 1.9dB 2.9dB 2.5dB\2.9dB
Inside Cable HT400- 75Feet 4.2dB 4.4dB 6.1dB 5.8dB\6.5dB
Inside Cable HTG58- 30Feet 4.5dB 4.9dB 7.6dB 7.2dB\8dB
Inside Cable HT400- 20Feet 1.3dB 1.35dB 1.8dB 1.8dB\1.9dB
Inside Cable HTG58- 15Feet 2.3dB 2.5dB 3.9dB 3.7dB\ 4.1dB
Inside Cable HT400- 30Feet 1.9dB 1.95dB 2.8dB 2.55dB\2.9dB
Outside
Antenna
HT Log periodic
antenna
7dBi 7dBi 10dBi 10dBi\10dBi Direconal
antenna
Outside
Antenna
HT Yagi antenna 9dBi 9dBi \ \ Direconal
antenna
Outside
Antenna
HT Wall
antenna
9dBi 9dBi 9dBi 9dBi Direconal
antenna
Inside
Antenna
HT Wall antenna 9dBi 9dBi 9dBi 9dBi\9dBi Direconal
antenna
Inside
Antenna
HT Rod antenna 1dBi 1dBi 0dBi 0dBi\0dBi Omni antenna
Inside
Antenna
HT
Omnidireconal
ceiling antenna
3dBi 3dBi 3dBi 3dBi Omni antenna
Lightning
Protector
HT-LP01 0.1 dB 0.1 dB 0.18dB 0.16dB\0.2dB For any
external
antenna
All equivalent antennas and cables are suitable for use with the ROOMBOOST.

This booster including safeguards to protect the cellular network from
interference. Each Signal Booster is individually tested and factory set to ensure FCC
compliance.
1.The Signal Booster cannot be adjusted without factory reprogramming or
disabling the hardware.
2.The Signal Booster will amplify, but ONLY incoming and outgoing signals in
order to increase coverage of authorized frequency bands.
3.If the Signal Booster is not in use for five minutes, it will reduce gain unl a
signal is detected.
4.If a detected signal is too high in a frequency band, or if the Signal Booster
detects an oscillaon, the Signal Booster will automacally turn the power off on
that band.
5.For a detected oscillaon the Signal Booster will automacally resume normal
operaon aer a minimum of 1 minute. Aer 5 mes consecuve such automac
restarts, if the detected oscillaon sll remains, any problemac bands are
permanently shut off unl the Signal Booster has been manually restarted by
reconnecng power supply to the Signal Booster.
6.Noise power, gain, and linearity are maintained by the Signal Booster's
microprocessor.
Descripon of network protecon features:
This device complies with Part 15 of FCC Rules. Operaon is subject to the
following two condions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operaon. This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protecon against harmful
interference in a residenal installaon. This equipment generates and can radiate
radio frequency energy and, if not installed and used in accordance with the
instrucons, may cause harmful interference to radio communicaons. However,
there is no guarantee that interference will not occur in a parcular installaon. If
this equipment does cause harmful interference to radio or television recepon,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures: -- Reorient or relocate the receiving antenna. -- Increase the separaon
between the equipment and receiver. -- Connect the equipment into an outlet on a
circuit different from that to which the receiver is connected. -- Consult the dealer
or an experienced radio/TV technician for help
6
If you have any quesons or concerns when installing or
operang your cell phone booster, please email us:
[e-mail]