Rosewill RNX-N600PCE_v2.0 User manual

RNX-N600PCE_v2.0
N600 Wireless Dual Band PCI Express Adapter
1910020741
REV1.0.0

COPYRIGHT & TRADEMARKS
Specifications are subject to change without notice is a registered trademark of
Rosewill Inc. Other brands and product names are trademarks or registered trademarks of their
respective holders.
No part of the specifications may be reproduced in any form or by any means or used to make
any derivative such as translation, transformation, or adaptation without permission from
Rosewill Inc. Copyright © 2015 Rosewill Inc. All rights reserved.
http://www.Rosewill.com

FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1） This device may not cause harmful interference.
2） This device must accept any interference received, including interference that may
cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Note: The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this equipment. Such modifications could void the user’s authority
to operate the equipment.
Warning
According to old rule of 15.407, the frequency band of 5150-5250 MHz is restricted, this equipment
is indoor using only.
Radiation Exposure Statement:
The product comply with the FCC portable RF exposure limit set forth for an uncontrolled environment
and are safe for intended operation as described in this manual. The further RF exposure reduction can
be achieved if the product can be kept as far as possible from the user body or set the device to lower
output power if such function is available.

CE Mark Warning
This is a class B product. In a domestic environment, this product may cause radio interference, in
which case the user may be required to take adequate measures.
National Restrictions
This device is intended for home and office use in all EU countries (and other countries following
the EU directive 1999/5/EC) without any limitation except for the countries mentioned below:
CountryRestrictionReason/remark
Bulgaria None General authorization required for outdoor use
and public service
France
Outdoor use limited to
10 mW e.i.r.p. within
the band 2454-2483.5
MHz
Military Radiolocation use. Refarming of the 2.4 GHz
band has been ongoing in recent years to allow current
relaxed regulation. Full implementation planned 2012
Italy None If used outside of own premises, general authorization is
required
Luxembourg None General authorization required for network and service
supply(not for spectrum)
Norway Implemented
This subsection does not apply for the geographical
area within a radius of 20 km from the centre of Ny-
Ålesund
Russian Federation None Only for indoor applications
Note: Please don’t use the product outdoors in France.
This device has been designed to operate with the antennas listed below, and having a maximum
gain of 1.8 dBi. Antennas not included in this list or having a gain greater than 1.8 dBi are strictly
prohibited for use with this device. The required antenna impedance is 50 ohms.
To reduce potential radio interference to other users, the antenna type and its gain should be so
chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for
successful communication.

Canadian Compliance Statement
This device complies with Industry Canada license-exempt RSS standard(s). Operation is
subject to the following two conditions:
(1)This device may not cause interference, and
(2)This device must accept any interference, including interference that may cause undesired
operation of the device.
Cet appareil est conforme aux norms CNR exemptes de licence d’Industrie Canada. Le
fonctionnement est soumis aux deux conditions suivantes:
(1)cet appareil ne doit pas provoquer d’interférences et
(2)cet appareil doit accepter toute interférence, y compris celles susceptibles de provoquer un
fonctionnement non souhaité de l’appareil.
Industry Canada Statement
Complies with the Canadian ICES-003 Class B specifications.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
This device complies with RSS 210 of Industry Canada. This Class B device meets all the
requirements of the Canadian interference-causing equipment regulations.
Cet appareil numérique de la Classe B respecte toutes les exigences du Règlement sur le
matériel brouilleur du Canada.
Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам
нормативних документів та вимогам, що передбачені чинними законодавчими актами
України.
Safety Information
z When product has power button, the power button is one of the way to shut off the product;
when there is no power button, the only way to completely shut off power is to disconnect the
product or the power adapter from the power source.
z Don’t disassemble the product, or make repairs yourself. You run the risk of electric shock
and voiding the limited warranty. If you need service, please contact us.
z Avoid water and wet locations.
This product can be used in the following countries:
AT BG BY CA CZ DE DK EE
ES FI FR GB GR HU IE IT
LT LV MT NL NO PL PT RO
RU SE SK TR UA US


CONTENTS
PackageContents................................................................................................ 1
Chapter1ProductOverview .............................................................................. 2
1.1 Introduction................................................................................................................ 2
1.2 Features ...................................................................................................................... 2
1.3HardwareOverview ..................................................................................................... 2
Chapter2Installation ........................................................................................ 3
2.1HardwareInstallation ................................................................................................. 3
2.2 SoftwareInstallation ................................................................................................... 4
Chapter3ConnecttoaWirelessNetwork.......................................................... 8
3.1To connectusingRosewillWirelessConfigurationUtility .......................................... 8
3.2 To connectusingWPS ............................................................................................... 12
3.2.1 PBC(PushButtonConfiguration)method........................................................... 12
3.2.2 PINmethod......................................................................................................... 14
3.3To connectusingWindowsbuilt‐inwirelessutility ................................................... 16
3.3.1 InWindowsXP .................................................................................................... 16
3.3.2 InWindowsVista................................................................................................ 19
3.3.3 InWindows7...................................................................................................... 21
3.3.4 InWindows8...................................................................................................... 22
Chapter4Management ................................................................................... 25
4.1 Profile........................................................................................................................ 25
4.1.1 Addaprofile........................................................................................................ 25
4.1.2 Modifyaprofile .................................................................................................. 30
4.1.3 Deleteaprofile ................................................................................................... 30
4.2Advanced .................................................................................................................. 30
4.3About........................................................................................................................ 31
Chapter5SoftAPMode(ForWindows7andWindows8) ................................ 32
Chapter6UninstallSoftware............................................................................ 34
6.1InWindowsXP/Vista/7 ............................................................................................. 34
6.1.1 UninstalltheutilitysoftwarefromyourPC......................................................... 34
6.1.2 UninstallthedriversoftwarefromyourPC ........................................................ 35
6.2InWindows8............................................................................................................ 37
6.2.1 UninstalltheutilitysoftwarefromyourPC......................................................... 37
6.2.2 UninstallthedriversoftwarefromyourPC ........................................................ 39
AppendixA:Specifications................................................................................ 41
AppendixB:Glossary ........................................................................................ 42

RNX-N600PCE_v2.0 N600 Wireless Dual Band PCI Exp
r
ess Adapte
r
User Guide

1
Package Contents
Please verify that all the package contents below are available.
¾ One RNX-N600PCE_v2.0 N600 Wireless Dual Band PCI Express Adapter
¾ Quick Installation Guide
¾ One Resource CD for RNX-N600PCE_v2.0, including:
• Rosewill Wireless Configuration Utility and Drivers
• User Guide
• Other helpful information
Make sure that the above items are contained in the package. If any of the above items is
damaged or missing, please contact your distributor.
)
Note:
The ‘adapter’ mentioned in this User Guide stands for RNX-N600PCE_v2.0 N600 Wireless Dual
Band PCI Express Adapter without any explanation.

RNX-N600PCE_v2.0 N600 Wireless Dual Band PCI Exp
r
ess Adapte
r
User Guide

2
Chapter 1 Product Overview
1.1 Introduction
The adapter is a dual band 802.11n client device designed to deliver a high-speed wireless
performance for your desktop. With a faster wireless connection, you can get a better Internet
experience, such as downloading, gaming, and video streaming.
With the 802.11n technology, higher throughput improvements using 2T2R, the RNX-
N600PCE_v2.0’s auto-sensing capability allows high packet transfer rate of up to 300Mbps for
maximum throughput. It has good capability on anti-jamming, and it can also interoperate with
other wireless (802.11a/b/g) products. The adapter supports WEP, WPA-PSK/WPA2-PSK and
WPA/WPA2 encryption to prevent outside intrusion and protect your personal information from
being exposed.
The adapter is easy to install and manage. The Quick Setup Wizard will guide you step-by-step
through the installation process and the Rosewill Wireless Configuration Utility will instruct you to
quickly set up a wireless connection.
With unmatched wireless performance, reception, and security protection, the RNX-
N600PCE_v2.0 is the best choice for easily adding or upgrading wireless connectivity to your
desktop.
1.2 Features
¾ Supports dual-band, 2.4GHz or 5GHz
¾ Seamlessly compatible with 802.11a/b/g/n products
¾ Experience smoother video streaming and online gaming by choosing the clearer 5GHz band
for wireless connections
¾ Supports 64/128 WEP, WPA/WPA2, WPA-PSK/WPA2-PSK(TKIP/AES), supports IEEE
802.1X
¾ Supports Windows XP 32/64bit, Vista 32/64bit, Windows 7 32/64bit, Windows 8 32/64bit
¾ Supports ad-hoc and infrastructure mode
¾ Bundled utility provides quick & hassle-free installation
1.3 Hardware Overview
LED status:
Status Working Status
Off
The driver has not been installed;
The adapter's radio has been disabled.
Flashing Slowly The driver has been installed but no data is being transmitted or received.
Flashing Quickly Data is being transmitted or received.

RNX-N600PCE_v2.0 N600 Wireless Dual Band PCI Exp
r
ess Adapte
r
User Guide

3
Chapter 2 Installation
Please install the PCI Express adapter into your computer before installing the driver and utility
software from the Resource CD.
2.1 Hardware Installation
1. Turn off your computer and unplug the power cord from the computer.
2. Open the case and locate an available PCI Express slot. Remove the metal slot cover on the
back of the PC. Keep the screws. Turn to your computer manufacturer for instructions if
needed.
3. Insert the PCI Express adapter into the PCI Express slot. Make sure that all of its pins have
touched the slot's contacts. Once the adapter has been firmly inserted, screw its fastening
tab. Then, close your PC case.
4. Insert the power cable back into the computer and turn on your computer.
) Note:
When the hardware has been successfully installed on your computer, you may be prompted
'Found New Hardware Wizard' (as shown in Figure 2-1 and Figure 2-2); please click Cancel,
and then follow the Software Installation steps to install driver and utility for your adapter.
Figure 2-1 Found New Hardware Wizard in Windows XP

RNX-N600PCE_v2.0 N600 Wireless Dual Band PCI Exp
r
ess Adapte
r
User Guide

4
Figure 2-2 Found New Hardware Wizard in Windows Vista
2.2 Software Installation
The adapter’s Setup Wizard will guide you through the installation procedures for Windows XP,
Windows Vista, Windows 7 and Windows 8. The procedures in different systems are quite
similar, therefore here we use the procedures in Windows 7 as an example.
1. Insert the Resource CD into your CD-ROM drive. Double-click Computer, and then double-
click the CD/DVD Drive where the installation CD was placed. Open RNX-N600PCE_v2.0
folder, and double-click Setup.exe to begin.
2. The InstallShield Wizard window will appear. Click Next to continue.
Figure 2-3

RNX-N600PCE_v2.0 N600 Wireless Dual Band PCI Exp
r
ess Adapte
r
User Guide

5
3. Choose a setup type. It is recommended to select Install Rosewill Wireless
Configuration Utility and Driver. Selecting Install Driver Only can only install driver.
Click Next to continue.
Figure 2-4
4. Click Change to specify the destination location for the software or you can leave it default.
Click Next in the screen below to continue.
Figure 2-5

RNX-N600PCE_v2.0 N600 Wireless Dual Band PCI Exp
r
ess Adapte
r
User Guide

6
5. Click Install to continue the setup.
Figure 2-6
6. The utility and drivers will install. It may take 1-2 minutes.
Figure 2-7

RNX-N600PCE_v2.0 N600 Wireless Dual Band PCI Exp
r
ess Adapte
r
User Guide

7
7. After all the steps above, you will see the screen below. Click Finish to complete the setup.
Figure 2-8
8. After installation, the utility configuration page will automatically pop up as shown in the
following figure and the icon will appear in your system tray. To connect to a network,
please refer to Chapter 3 Connect to a Wireless Network.
Figure 2-9

RNX-N600PCE_v2.0 N600 Wireless Dual Band PCI Exp
r
ess Adapte
r
User Guide

8
Chapter 3 Connect to a Wireless Network
With both the hardware and software successfully installed into your computer, you can quickly
connect to a wireless network using one of the following methods.
¾ Method One: To connect using Rosewill Wireless Configuration Utility
RNX-N600PCE_v2.0 uses the Rosewill Wireless Configuration Utility as the management
software. The utility provides you an easy interface to connect to a network and to change any
settings related to the wireless adapter.
¾ Method Two: To connect using WPS
By this method, you can connect to your network quickly on the condition that your Router or
access point supports WPS or QSS as is called by some other products.
¾ Method Three: To connect using Windows built-in wireless utility
Windows users may use the built-in wireless utility to connect to a wireless network. For specific
operations, please go to 3.3 To connect using Windows built-in wireless utility.
3.1 To connect using Rosewill Wireless Configuration Utility
1. After installation, the utility configuration page will automatically pop up on the screen. If the
utility page does not pop up, you can also launch the utility by double-clicking the icon
on your desktop.
Figure 3-1
2. The Network page will display all wireless networks that are available in your area. To
connect to a network, simply highlight the wireless network name (SSID) and click
Connect. If you tick Connect automatically, the adapter will automatically connect to your
target network next time.

RNX-N600PCE_v2.0 N600 Wireless Dual Band PCI Exp
r
ess Adapte
r
User Guide

9
Figure 3-2
3. You will be prompted different windows when you choose wireless network of different
security types.
1) Wireless network of WPA/WPA2-Personal
If you selected a wireless network of the security type WPA/WPA2-Personal, you will be
prompted to enter the password in the security key field, as shown in Figure 3-3. Or you
can push the WPS/QSS button on your Router (if it features the WPS/QSS function) to
quickly build a connection without entering the security key (password).
Figure 3-3
) Note:
The security key (password) can be found on the configuration page of your Router or Access
Point.

RNX-N600PCE_v2.0 N600 Wireless Dual Band PCI Exp
r
ess Adapte
r
User Guide

10
2) Wireless network of WPA/WPA2-Enterprise
If you selected a wireless network of the security type WPA/WPA2-Enterprise, you will be
prompted to choose a type of authentication, either Certificate or Password. With
Certificate as your authentication, you need to select one specific certificate from the
drop-down list, as shown in Figure 3-4. With Password as your authentication, you should
enter the right user name and password in the corresponding field, as shown in Figure 3-5.
Figure 3-4
Figure 3-5

RNX-N600PCE_v2.0 N600 Wireless Dual Band PCI Exp
r
ess Adapte
r
User Guide

11
3) Wireless network of None
If you selected a wireless network of None (that is, no security is set.), you can get directly
connected to this network without any further configuration.
4. Please wait a few minutes for the connection process.
Figure 3-6
5. You have now successfully connected to your network. Click Close to enjoy the
Internet.
Figure 3-7
6. To view more information about the network currently connected, click Status in the tools
section and the page will display information such as the network type, channel, rate, etc.

RNX-N600PCE_v2.0 N600 Wireless Dual Band PCI Exp
r
ess Adapte
r
User Guide

12
Figure 3-8
3.2 To connect using WPS
WPS (Wi-Fi Protected Setup) function allows you to add a new wireless device to an existing
network quickly.
If your wireless Router supports WPS or QSS (Quick Security Setup), you can establish a
wireless connection between wireless card and Router using either Push Button Configuration
(PBC) method or PIN method. Three WPS connection methods are listed in the following parts,
while the third method is only supported in Windows XP and Windows Vista.
3.2.1 PBC (Push Button Configuration) method
1. Press the WPS or QSS button on the Router. Here we use a Router as an example.
Press the WPS/Reset button for 2-3 seconds.

RNX-N600PCE_v2.0 N600 Wireless Dual Band PCI Exp
r
ess Adapte
r
User Guide

13
2. Open Rosewill Wireless Configuration Utility and click WPS tab. Select Push the button
on my access point or
wi reless router and then click Connect.
Figure 3-9
3. The adapter will be connecting to the target network.
Figure 3-10

RNX-N600PCE_v2.0 N600 Wireless Dual Band PCI Exp
r
ess Adapte
r
User Guide

14
4. When the following window appears, you have successfully connected to the network.
Figure 3-11
3.2.2 PIN method
There are two ways to configure the WPS by PIN method:
1) Enter the PIN from your Router or AP device.
2) Enter a PIN into your Router or AP device.
(
) Note: This method is only available in Windows XP and Windows Vista.)
Following are the detailed configuration procedures of each way.
3.2.2.1. Enter the PIN from your Router or AP device
1. Open Rosewill Wireless Configuration Utility and click WPS tab. Select Enter the PIN of
my access point or wireless router. In the empty field beside PIN, enter the PIN labeled
on the bottom of the Router (here takes 13492564 for example). If you have generated a
new PIN code for your Router, please enter the new one instead. Click Connect to
continue.
Figure 3-12