Rover RXD913GNAFD User manual

THANK YOU
FOR YOUR PURCHASE
www.roversystems.com.ph/utility-tools
we appreciate your feedback, you can email us at:
[email protected]
Available on App Store and Play Store
Rover 1000 Series eMobile 2 App

Installation Guidelines
Congratulations on your purchase of this product. We adopt the latest image sensor
and DSP technology. It features a very compact and discrete case. In addition, it can
provide high definition video, stable quality, strong anti-interference, rich and true to
life color. Installing this products is very convenient. It is the most technologically
advance CCTV system in the market today.
Please read this instruction manual carefully to ensure proper use of the products.

• C tail line of AHC interface instruction
Line Function Introduction
Serial Number Function
Video Output
DC12V Input
1
2
C1 Tail Line Interface Instruction
Electric Wire
Connect green and black
Connect black and white
and green
Connect black and white
Not shot
CVI
CVBS
TVI
AHD
Green
Black
White
Cable Interface Instruction
Video Output

Step3: Adjust the camera to the appropriate angle and tighten.
Bullet Camera Wall Installation
Before installing the camera, please make sure that all production in the
box are intact.
Step1: Install the wall bracket on the wall surface properly.
Step2: Install the camera on the wall bracket with screw and tighten.

Step1: Install the lifting scaffold in the ceiling properly.
Step2: Remove the camera sun shade screw, then install it on the lifting
scaffold and tighten.
Bullet Camera Housing Installation
Step3: Adjust the camera to the appropriate angle and tighten.

Step3: Use tapping screw to immobilize the camera pedestal on the wall and
adjust the camera movement to appropriate angle.
Step4: Mount camera shield and the front cover components, tighten the screw
and finish.
Step1: Paste the sticker on the wall and punch holes according to it.
Step2: Take out camera from the packing box and remove the protective and
components after loosening the screw on camera with a screwdriver.
Dome Camera Housing Installation
Note: You need to open line holes in case of threading through the wall.

Step3: Sort out the tail line of camera, aim the camera shell at snap joint,
buckle on the tighten.
Step4: Adjust the camera lens to the appropriate angle and finish.
Step1: Paste the sticker on the wall and punch holes according to it.
Step2: Use tapping screw to immobilize the camera pedestal on the all.
(If it is a cement wall, you need to install the expansion screw.)
Conch Camera Installation
Note: You need to open line holes in case of threading through the wall.

Connection Diagram

Coaxial Control Instruction
Coaxial control function can transmit the video signals and control signals
at the same time with a coaxial cable.
It is more convenient to debug and more easy to maintain. It also can
save the cost of control lines, control decoder, and labor cost.
It is equipped with special interface and function integration.
It doesn’t need to invoke frontend OSD. It has many languages to choose.
Note: The coaxial control function can be used in some camera only and it
should be used with AHD coaxial DVR.
Coaxial Control Operate Interface
Right click [Coaxial control], interface is as follows:
Drag the slider to adjust the parameters of hue, saturation and so on

Click [Advanced], interface is as follows:
Change the parameters of exposure mode, noise level and so on.

XVI / AHD / TVI / CVI /
CVBS@1080P
RXB913GHCFD RXBC13GHCFD
2.0MP 1/3" low illumination
CMOS sensor
5.0MP 1/2.7" low
illumination CMOS sensor
1/50(1/60)s to 1/10,000 s
Color:0.01Lux @(F1.2,AGC ON); 0 Lux with IR
B/W: 0.001 Lux @ (F1.2,AGC ON),0 Lux with IR
HD lens 2.8mm
XVI / AHD / TVI / CVI:
5MP@20fps 5MP@
12.5fps; CVBS:960H P/N
2 array lamps, 2 white lights "IR2": 20-30 meters
IR cut filter with auto switch
RXD913GNAFD

Please be advised that the Electronic Security Equipment are sensitive to
voltage surges. Majority of defects are caused by unstable 220VAC
power supply, power fluctuations, and transient surges. Furthermore, failure of
equipment is usually experienced after a brownout or after a thunderstorm.
In general, we recommend that you purchase a 12VDC Regulated Power Supply
and an Automatic Voltage Regulator with Power-On-Delay considering that these
have been tested to protect against the most common causes of damage to
CCTV System.