RS PRO 791-8258 User manual

Instruction Manual
Halogen lamp with UK plug (791-8258)
Halogen lamp with EU plug (791-8267)

2
Attention: Please read the following instructions carefully to ensure that mounting operation will be
carried out in the right way .These instructions should be properly preserved for future reference.
Main Construction Data:
Type
Rated Power
Glass
Weight
Maximum
projected
area
Dimensions
Max
height
of
stand
Remark
7918267
2*Max.400W
177x140x5mm
4.92Kg
2*0.02M2
265x185x125mm
0.93m
Electric shock protection class:Ⅰ
External light protection class:
IP54
Rated voltage:
220-240V~ 50Hz
Power cord: H05RN-F 3G1.0mm2
/ H07RN-F
3G1.5mm2&F3G1.0mm2
Halogen bulb: R7s 150W 78mm
,500W 118mm
EU (German) plug
7918258
2*Max.400W
177x140x5mm
4.92Kg
2*0.02M2
265x185x125mm
0.93m
Electric shock protection class:Ⅰ
External light protection class:
IP54
Rated voltage:
220-240V~ 50Hz
Power cord: H05RN-F 3G1.0mm2
/ H07RN-F
3G1.5mm2&F3G1.0mm2
Halogen bulb: R7s 150W 78mm
,500W 118mm
BS(UK) plug
Electrical Safety:
This floodlight must be earthed. If it becomes necessary to re-wire the plug please follow these guidelines.
Always secure wires in plug terminals carefully. Make sure the cable is firmly located in the cord grip. NEVER
connect the green & yellow wire to any terminal other than one marked with the earth symbol ‘E’or‘ ’,
Regularly inspect all electrical connections and wiring for damage. Any faults should be immediately rectified
before further use of this floodlight. Always have the wiring and connections checked by a qualified electrician.
In use, ensure all wiring and extension cables are kept clear of any cutting tools, sharp objects and any other
potential hazard such as wet floors, chemicals, solvents etc.

3
NOTE:
If your mains wiring differs in any way from Diagram A. Consult a qualified electrician. Always ensure that the
mains supply voltage is correct. Always replace the fuse with one of an identical rating.The lighting direction
can not be adjusted to down ward.If the external flexible cable or cord of this Luminaire is damaged, it shall be
exclusively replaced by the manufacturer or his service agent or a similar qualified person in order to avoid a
hazard.
Caution:
This unit can become extremely hot whilst in operation do not touch the unit until it has had time to cool down.
Make sure these floodlights are far enough away from any combustible materials and/or surfaces. Make sure
there is adequate ventilation to aid heat dissipation.
Assembly And Use:
The tripod stand is supplied assembled, To attach this floodlight you must first
erect the stand.
To open the legs push the spring pin upwards and, at the same time, pivot the
leg down. Release the spring pin whist pivoting the leg and the pin will locate
into one slot (see Diagram2)
To alter the stand height twists the locks (D) anti-clockwise to release, slide the
tubes to desired height and tighten the twist locks clockwise (see Diagram3)
Attach this floodlight to the crossbar (A) by securing with the screw knob nut &
bolt assemblies(C) through the centre hole on the brackets of each this
floodlight. Unscrew the centre knob (B). The bracket on the central wiring block
(G) should be situated between the top of the stand and the crossbar (A). Re-
insert the centre screw knob (B) through the central hole of the crossbar (A) and
the hole in the central wiring block bracket (G). The crossbar can be swivelled, if
required, by loosening the knob (B) moving the crossbar, and retightening the
knob. To adjust this floodlight angle, loosen the screws located on either side of
the bracket, until the desired angle is achieved, then re-tighten.
Check this floodlight is secure and that the stand is stable and has a firm
footing. Ensure cable is not catching on any sharp object and that the mains
plug connection is adequately protected against rain or moisture. Your floodlight
is now ready for use.

4
Fitting The Lamp:
To fit the supplied halogen bulbs you need to loosen the screw (H) securing the hinged front cover and swing
the cover down. The bulb is attached by spring-loaded holders at each end. Gently locate the bulb into
position, ensuring good contact at both ends. Take care not to touch the glass of the bulb. If this does occur
clean the bulb with methylated spirit. Close the hinged front cover and re-tighten the top retaining screw
(H).DO NOT OVERTIGHTEN, THIS MAY DAMAGE THE GLASS.