RS 776-9361 User manual

OWNER’S MANUAL
How to use CCTV camera
RS Part No. 776-9361
Instruction Manual
Colour IR Camera
776-9361
Digital

RS PART No.:776-9361
OWNER’S MANUAL
How to use Bullet camera
776-9361
Before Using or Installing
Please do not make any attempt to disassemble the camera.
To avoid any electrical shock, Please do not remove camera cover &
screw.
Please consult with Installation specialist since there is no user
execution.
Please do not use strong chemicals or detergent.
Use dry towel to wipe off the camera, to clean off the stain use weak
Cleaning detergent.
Before operation please check the temperature, humidity, and level of
the power.
Please operate camera between temperature levels of -10℃~ 50℃.
Please do not disclose the camera, if there is lot of smoke or gas.
Please do not disclose the camera under direct sunlight.
Do not aim camera directly at bright object.
By doing so, this action will cause blooming or smear.
Please handle camera with care.
Do not put camera near fire, as this may cause fire.
Please do not hit, or shake the camera.
This could cause camera to malfunction.
Improper care or use of the camera could damage the camera.
Please do not make children handle or operate camera. It may
cause children’s accidents or camera’s malfunction.
.How to Use &Installations & Warnings
Use of DC12V. ( Please use Adapter 500mA for DC12V).
Please use dry towel to clean camera instead of the abrasive.
(This could bring low quality screen view of camera)
Please do not misplace the camera. And prevent any malfunction.
Please do not use camera in humid or wet area.
Do not disclose camera to direct sunlight
Do not expose camera to massive electric wave.
Do not install camera location with lot of vibration.
Do not install product near very high temperature or very low
temperature area. (Please refer to our operation manual on
operation temperature & storage temperature)
Do not attempt to open dome cover after installation and
image adjustment
OSD MENU TREE
RS PART No.:776-9361
DIGITAL COLOR VARIFOCAL IR LED CAMERA
►CAUTION
•
Do not open or strike this equipment. Sensitive electronics inside are vulnerable to excessive shock.
• Do not install the equipment near any naked flames or heat sources. Excessive heat could damage this unit.
• Do not cover cloth or to install this unit in poorly ventilated places. This may lead to overheating.
• Do not continue to operate if there appears to be fault.
If the unit ceases to function, contact qualified service personnel for help.
• Do not touch the power connection with wet hands. Risk of short circuit or electric shock.
• Do not damage the power cord or leave it under pressure. Risk of fire or shock circuit.
FEATURE
1/3" COLOR SONY SUPER HAD II CCD
OSD control button
HIGH RESOLUTION (70Φ, 34LEDs)
& Video connector
700TV Line
Min. Illumination : 0 Lux (IR ON)
OSD Control-ATR/BLC/HSBLC
2.8~12mm DC IRIS LENS
Power Source : DC 12V(6.5~28V)
Internal Adjustment OSD button
Service Video Connector
Weather-proof, IP 67
776-9361
* INSTALLING THE CAMERA
1. Statation Bracket on the wall or ceiling with the screw give
to your desire area.
2. Loosen up the joint on the bracket using “L” wrench and set
bracket to the direction you want to monitor and tighten it
3. Fix Sunshield on this camera.
* How to adjust OSD key for OSD menu
1. Open camera case at half portion of housing.
2. Adjust OSD menu to use
OSD key in the board.
You can use Service
video connector with
portable monitor to
configue the setting
easily
3.
* After configration close
the case tightly to prevent
any water-smear.
OSD key
Service Video connector
Trouble Shooting
If you are not able to view anything from the screen.
* Check power, video, strengh of signal. & Monitor input/output.
* Check cameras connection No with monitor/
FOR FUZZY SCREEN
* Check camera lens for dust or dirt. If so wipe them of with dry
towel or brush
* Check for direct sunlight exposure towards camera.
* Check if protection firm from camera cover is removed
FOR DARK SCREEN
* Check for monitor brightness. Unbalanced black & white on it.
* Check Monitor
* Adjust the camera position or angle of lens when screen is bright
if problem still remains please contact our technicial supporter.
:SET
:SET
This camera utilized an On Screen user MENU.
To set iems on the menu, use the following
switch.
* UP * DOWN
* LEFT * RIGHT
* SET
SPECIFICATION
Image Device
Picture Elements
Scanning System
Sync System
Horizontal Resolution
Video Output
S/N Ratio
LENS
Minimum Illumination
White Balance
Exposure
Shutter Speed
Backlight Compensation
Privacy Masking
Day & Night
Motion Detection
2D-DNR
Digital Effect
Sharpness
Power Consumption
Operation Temperature
Storage Temperature
Weight
Housing
Dimension(mm)
Cable(option)
Off / On
Off / On (Adjustable)
Off / Mirror
Adjustable
OSD
FUNCTI
ONs
ATW(1800°K ~ 10,500°K) / Push / User1 / User2 /
Anti CR / Manual / Push-Lock
ELC / ALC
Auto / Manual
(1/60~1/10,000sec)
Auto / Manual
(1/50~1/10,000sec)
ATR / BLC / HLC
8 Zone
Auto / Color / BW / EXT1 / EXT2
70Φ, 34LEDs
20 ℃~＋60℃, RH95% Max
Approx 695 g
DC12(6.5V~28V)/ 300mA(IR on)
10 ℃~＋50℃, RH95% Max (14˚F~122˚F)
ALUMINUM
Standard 1200mm BNC/DC Jack
0.1Lux(Day), 0.005Lux(Night) (F:1.2)
1/3" SONY 960H SUPER HAD II CCD
1020(H)×508(V)
1020(H)×596(V)
2:1 Interlace
Internal Synchronization
1Vp-p 75Ω
700 TV Line
MORE THAN 50dB (AGC Off)
NTSC
PAL
2.8 ~ 12mm Varifocal Lens, DC IRIS
1Level 2Level
CAMERA ID ON / OFF
MANUAL
BACKLIGHT
PUSH
USER1
USER2
ANTI CR
MANUAL
PUSH LOCK
AUTO
COLOR
B / W
EXT1
EXT2
OFF
NR
OFF
ON
OFF
ON
PIC ADJUST
CAMERA RESET
EXIT
3Level
DETECT SENSE/BLOCK DISP/
MONITOR AREA/AREA SEL
/SENSITIVITY
LEVEL (024~127)
NR MODE / Y LEVEL / C LEVEL
LANGUAGE
ENGLISH / JP / DEUTSCH / FRANCAIS / RUA /
PORTUGUES / ESPANOL
SAVE ALL
B-GAIN / R-GAIN : 0~255
B-GAIN / R-GAIN : 0~255
MIRROR/CONTRAST/SHARPNESS/HUE/GAIN
AREA/BOTTOM/RIGHT/COLOR
/TRANSP/MOSAIC
TOP/BOTTOM/LEFT/RIGHT
PRIVACY
LUMINANCE / CONTRAST
ATR
MOTION DET
ON
RETURN
DAY&NIGHT
BURST/IR OPTIMIZER/MODE/LEVEL
BURST/DELAY CNT
/DAY-NIGHT/NIGHT-DAY
WHITE BAL
SUTTER/AGC
HIGH LUMINANCE
MODE / SHUTTER / AGC
AUTO
LOW LUMINANCE
ATW
SPEED/DELAY
/ATR FRAME/ENVIRONMENT
OFF / BLC / HLC