RSA 5 Series User manual

Series 5 10G Network Daughter Card
Installation Guide

Copyright © 1994-2018 Dell Inc. or its subsidiaries. All Rights Reserved.
Contact Information
RSA Link at https://community.rsa.com contains a knowledgebase that answers common
questions and provides solutions to known problems, product documentation, community
discussions, and case management.
Trademarks
For a list of RSA trademarks, go to www.emc.com/legal/emc-corporation-trademarks.htm#rsa.
License Agreement
This software and the associated documentation are proprietary and confidential to Dell, are
furnished under license, and may be used and copied only in accordance with the terms of such
license and with the inclusion of the copyright notice below. This software and the
documentation, and any copies thereof, may not be provided or otherwise made available to any
other person.
No title to or ownership of the software or documentation or any intellectual property rights
thereto is hereby transferred. Any unauthorized use or reproduction of this software and the
documentation may be subject to civil and/or criminal liability.
This software is subject to change without notice and should not be construed as a commitment
by Dell.
Third-Party Licenses
This product may include software developed by parties other than RSA. The text of the license
agreements applicable to third-party software in this product may be viewed on the product
documentation page on RSA Link. By using this product, a user of this product agrees to be fully
bound by terms of the license agreements.
Note on Encryption Technologies
This product may contain encryption technology. Many countries prohibit or restrict the use,
import, or export of encryption technologies, and current use, import, and export regulations
should be followed when using, importing or exporting this product.
Distribution
Dell believes the information in this publication is accurate as of its publication date. The
information is subject to change without notice.
January 2018

Contents
About this Document 4
Series 5 10G Network Daughter Card Installation 5
10G Network Daughter Card KitPackage Contents 5
RearView of Series 5 Appliances (Except Hybrid) 5
R630System Board 6
Parts for Installing or Replacing the 10G Network Daughter Card 7
Install a 10G Network Daughter Card 9
RearView of Series 5 Hybrid Appliance 11
R730xd(Hybrid) System Board 12
Install a 10G Network Daughter Card in an R730xd (Hybrid) 14

Series 5 10G Network Daughter Card Installation Guide
About this Document
This document provides 10G Network Daughter Card information and installation procedures for
NetWitness Suite Series 5 appliances (hosts).
The hardware setup instructions in this document are for hardware only; they do not apply to a
specific release of NetWitness Suite software. After completing the hardware setup, please
continue setup and configuration of the NetWitness Server appliance as described in the
NetWitness Suite online documentationat RSA Link (https://community.rsa.com/docs/DOC-
40370).
This document is not a replacement for the original manufacturer's documentation; it contains
information specifically for the NetWitness Suite appliances.
Note: When viewing a printed guide, be aware that a newer version of the guide may be
available online at RSA Link in RSA NetWitness Suite under Hardware Setup Guides:
https://community.rsa.com/community/products/netwitness/hardware-setup-guides
About this Document 4

Series 5 10G Network Daughter Card Installation Guide
Series 5 10G Network Daughter Card Installation
Expansion cardscan be installed in RSA Series 5NetWitness Suite appliancestoadd
functionality to the system. This topic provides the general procedure for installing a 10G
Network Daughter cardinto the NetWitness Suite Series 5 appliances. All but one of the Series
5 appliances arebased on the Dell PowerEdge R630chassis. The exception isthe Hybrid
appliance,which is based on the Dell PowerEdge R730xd chassis.
10G Network Daughter Card KitPackage Contents
The kit consists of the following:
1. 10G Network Daughter card
2. ESD Wrist Strap
3. Warranty Label
4. Series 5 10G Network Daughter Card Installation Guide(this document)
Caution: The 10G Network Daughter card includes a Small Form-factor Pluggable
Transceiver (SFP).
It is important that you only use the SFP that comes with the 10G Network Daughter card.
RearView of Series 5 Appliances (Except Hybrid)
The following figure shows a PERC H830 RAID controller in slot 3.
Note: A missing or an unsupportedcardriser logs an SEL event. It does not prevent your
system from powering on and aBIOS POST message or F1/F2 pause is not displayed.
5 Series 5 10G Network Daughter Card Installation

Series 5 10G Network Daughter Card Installation Guide
R630System Board
Key Description Key Description
1 Control panel location 9 Riser card 1
2 Cooling fans (2) 10 Riser card 2
3 Processor 1 11 DIMMS (6)
4 DIMMS (6) 12 Processor 2
5 PSU connector 13 DIMMS (12)
6 Power supply (2) 14 Expander board
Series 5 10G Network Daughter Card Installation 6

Series 5 10G Network Daughter Card Installation Guide
Key Description Key Description
7 Riser card 3 15 Hard drive
8 Network daughter card
Parts for Installing or Replacing the 10G Network Daughter Card
The following figureshows how to remove the PERC H830 expansion card to gain access to the
Network Daughter card.
Key Description
1 Connector
2 Expansion-card latch
3 PERC H830 expansion card
4 Back panel slot
7 Series 5 10G Network Daughter Card Installation

Series 5 10G Network Daughter Card Installation Guide
The following diagram shows the parts used when replacing the 10G Network Daughter card.
Key Description Key Description
1 Captive screw socket (2) 4 Touch point (2)
2 Connector on the system board 5 Network daughter card
3 Captive screw (2) 6 Back panel slot for Ethernet connectors
Series 5 10G Network Daughter Card Installation 8

Series 5 10G Network Daughter Card Installation Guide
Install a 10G Network Daughter Card
The following procedure shows how to install a 10G network daughter card in a NetWitness
Suite Series 5 R630 appliance.
Caution: Many repairs may only be done by a certified service technician. You should only
perform troubleshooting and simple repairs as authorized in your product documentation, or as
directed by the online or telephone service and support team. Damage due to servicing that is
not authorized by RSA is not covered by your warranty. Read and follow the safety
instructions that came with the product.
Note: As long as the repairs and servicing made are allowed under customer support, your
warranty will not be voided.
To install the R630 10G Network Daughter card:
Note: Be sure to keep your #2 Phillips screwdriver handy.
1. Turn off the system, including any peripherals.
2. Disconnect the system from the electrical outlets and any attached peripherals, as well any
network interface cables.
3. Make sure to protect yourself by wearing an anti-static wrist strap before touching any
internal parts. An ESD wrist strap is provided for this purpose.
4. Remove the Warranty label on the server.
5. Open the system.
6. To remove the PERC H830 expansion card from riser card 3, lift the expansion-card latch.
7. Grasp the expansion card by its edges and remove it from the expansion-card connector on
the riser card 3.
8. Holding the touch points of riser card 3, lift the expansion-card riser from the riser connector
on the system board.
9. Using a #2 Phillips screwdriver, loosen the two captive screws that secure the network
daughter card to the system board.
10. Hold the network daughter card by the edges on either side of the touch points and lift to
remove it from the connector on the system board.
11. Slide the network daughter card away from the back of the system until the Ethernet
connectors are clear of the slot in the back panel.
12. Lift the network daughter card out of the system.
9 Series 5 10G Network Daughter Card Installation

Series 5 10G Network Daughter Card Installation Guide
13. Angle the new network daughter card so that the Ethernet connectors fit through the slot in
the back panel.
14. Align the captive screws at the back-end of the card with the screw holes on the system
board.
15. Press the touch point on the card to ensure that the connector on the card is in contact with
the connector on the system board.
16. Using a #2 Phillips screwdriver, tighten the two captive screws to secure the network
daughter card to the system board.
17. Install expansion-card riser 3.
18. Holding the PERC H830 card by its edges, position the card so that the card-edge connector
aligns with the expansion-card connector.
19. Insert the card-edge connector firmly into the expansion-card connector until the card is fully
seated.
20. Slide the expansion-card latch into position.
21. Close the system.
22. Replace the Warranty label on the server with a new label provided with the PCI card.
23. Reconnect the system to the electrical outlets and any attached peripherals, as well as any
network interface cables.
Series 5 10G Network Daughter Card Installation 10