Rubinet 1ARBETL User manual

INS ET1A
REMOVAL OF FAUCET:
Always turn the water supply off before removing the existing faucet or
disassembling a valve. Open both faucet handles to relieve water
pressure and to ensure that the water has been successfully turned off.
CARE OF FAUCET:
The use of warm water and a soft cloth is all that is required to clean
Rubinet products. The patina of our living finishes (Oil Rubbed Bronze &
Tuscan Brass) will change as a result of normal use. Applying Mineral Oil
on occasion will create a softer look, subtle color changes and character.
TWO HANDLE WIDESPREAD LAVATORY SET
MODEL 1ARBETL
If you need assistance with installation, replacement parts or have any
questions regarding your Rubinet product, please call a Customer
service representative at: 905-851-6781 toll free 1-800-461-5901
or visit www.rubinet.com
INS ET1A
LIFT ROD
POP-UP ROD
THUMB SCREW
SPRING CLIP
LOCK NUT
ADJUSTMENT
SCREW
TAIL PIECE
Assemble the Lift Rod as shown,
Nylon Bearing first then the Rod and
finally the Rod Nut.
Insert the Pop-Up Rod in the Spout.
Push the Lift Rod down to the Open
Drain Position. Connect the Pop-Up
Rod to the Extension Ladder as
shown using the Spring Clip and
Thumb Screw to secure both pieces
together.
Insert the Drain Plug into the sink.
With the Pop-Up Rod all the way
down the drain should be open. To
close it, lift the Pop-Up Rod. The
Drain Plug works on gravity and has
an adjustment screw. Loosen the
Lock Nut to make any adjustment
required then re-tighten the Lock Nut
to maintain the adjustment.
Hook up the ‘P’ Trap to the Drain Tail
Piece.
Finally, connect the water supply from
the Shut-Off valves (not supplied) to
the bottom of the Sidebodies.
Remove the Aerator from the spout
and flush the system to clear any
debris that might have accumulated
and replace the aerator.
13 14
15 16
17 18
WIDESPREAD LAV SET POP-UP DRAIN ASSEMBLY
4 1

INS ET1AINS ET1A
BRASS NUT
METAL WASHER
RUBBER WASHER
JIG
BRASS NUT
SPACER
FLANGE
TRIM RING
HANDLE
From the Mounting Kit, assemble one Brass
Nut, one Metal Washer and one Rubber
Washer to each Sidebody as shown.
Mount each Sidebody (HOT on the left COLD
on the right) from under the sink/deck and
assemble another Rubber Washer Metal
Washer and Nut, to the top side of each
Sidebody.
Next using the Jig provided, adjust the
top side Brass Nut so that the correct
sidebody height is achieved.
Tighten the Brass Nut on the
underside of the sink/deck to secure
each sidebody.
Place the Trim Rings as shown and
screw both Flanges to the Sidebodies.
Install the small Teflon Spacer atop
each flange before attaching the
Handles.
Turn each valve off and position each
Handle as required before tightening
the Set Screw using the Allen Key
provided.
1 2
3 4
5 6
SUPPLY HOSES
THREADED ROD
POP-UP BASKET
RUBBER WASHER
LIFT-ROD HOLE
To the bottom of the Spout assemble
both Supply Hoses (HAND TIGHTEN
ONLY) and the Threaded Rod from
the Spout Mounting Kit.
Place the Spout Trim Ring over the
centre hole and assemble the Spout
as shown.
From the underside of the sink/deck
assemble the remaining parts of the
Spout Mounting Kit to the Threaded
Rod. Rubber Washer first then the
Metal Washer and finally the Tie
Down Screw to secure the spout.
Attach each Supply Hose to the
corresponding Sidebody. Do not over
tighten.
Insert the Pop-Up Basket and Rubber
Washer as shown in the sink.
Plumbers putty can be used instead
of the Rubber Washer if prefered.
Assemble the remaining Pop-Up parts
under the sink in the order shown,
making sure that the Lift-Rod Hole is
facing the back of the sink.
7 8
9 10
11 12
2 3