Rubinet LaSalle 1GLAC User manual

1GLAL
1GLAC
1GLAR
Loosen the lock nut using
* 17mm Deep Socket.
1/2“ Drive
LOCK NUT
Recommended
torque 20Nm
12
56
HANDLE ALIGNMENT (1G)
34
Use Handles to
unscrew cartridge.
Turn both splines
counter clock-wise.
Once cartridge valves are loose, screw them
back into the faucet using the handle.
Stop when you feel a noticeable resistance.
Then remove handles.
Replace Left Handle (hot) one tooth o
from the OFF position as shown.
And Right Handle (cold) one tooth o
from the ON position as shown.
Turn the handles to the desired alignment.
(This will unscrew the cartridge)
This adjustment should not be more than 25º.
Tighten Lock Nut using 17mm Deep Socket.
wrench to secure cartridge valve position.
*Use handle to hold spline while tightening.
Remove
THREADED
SLEEVE
LOCK NUT
6
WALL MOUNT LAVATORY SET
ASSEMBLY INSTRUCTION 1GLAL - C - R
REMOVAL OF FAUCET:
Always turn the water supply off before removing the existing faucet or disassembling a valve. Open both faucet handles to relieve water pressure
and to ensure that the water has been successfully turned off.
CARE OF FAUCET:
The use of warm water and a soft cloth is all that is required to clean Rubinet products. The patina of our living nishes (Oil Rubbed Bronze &
Tuscan Brass) will change as a result of normal use. Applying Mineral Oil on occasion will create a softer look, subtle color changes and character.
CONTACT US:
If you need assistance with installation, replacement parts or have any questions regarding your Rubinet product,
please call a Customer Service representative at: 905-851-6781 toll free 1-800-461-5901 or visit www.rubinet.com
210301

WALL MOUNT LAVATORY SET 1GLAL-C-RWALL MOUNT LAVATORY SET 1GLAL-C-R
1GR1001GR100
Wall Mount Valve Wall Mount Valve
Rough-InRough-In
HLA04HLA04
Cross HandleCross Handle
HLA01HLA01
Lever HandleLever Handle
5
IF THE HANDLES DO NOT ALIGN CORRECTLYIF THE HANDLES DO NOT ALIGN CORRECTLY
You can adjust them. Please refer to the You can adjust them. Please refer to the
‘Handle Alignment’ instruction at the back.‘Handle Alignment’ instruction at the back.
Lock NutLock Nut

1 5/8˝
4 1
1 7/8˝
WALL MOUNT LAVATORY SET 1GLAL-C-RWALL MOUNT LAVATORY SET 1GLAL-C-R
MUST CUT FLUSHMUST CUT FLUSH
TO THE FLANGE TRIMTO THE FLANGE TRIM
* 1 7/8˝ (47.5mm) * 1 7/8˝ (47.5mm)
from the nished wallfrom the nished wall
FlangeFlange
Pre-assembled Spout RingPre-assembled Spout Ring
* Cut the Slip-Fit Shank 1 5/8˝ long from the Cut the Slip-Fit Shank 1 5/8˝ long from the
nished wall and nished wall and MUST REMOVE ANY
BURRS before installing the Wall Spout.before installing the Wall Spout.
Tighten set screws to secure

2 5/8˝
2 3
WALL MOUNT LAVATORY SET 1GLAL-C-RWALL MOUNT LAVATORY SET 1GLAL-C-R
Turn each cartridgeTurn each cartridge
splines intosplines into OFFOFF positionposition
before installing handlesbefore installing handles
Place handle on the spline.Place handle on the spline.
Flange Flange
BushingBushing
CUT THE SPLINE TO FITCUT THE SPLINE TO FIT
* 2 5/8˝ (67 mm)* 2 5/8˝ (67 mm)
from the nished wallfrom the nished wall
IF THE HANDLE DOES NOT FITIF THE HANDLE DOES NOT FIT
Tighten set screws to secure

2 5/8˝
2 3
WALL MOUNT LAVATORY SET 1GLAL-C-RWALL MOUNT LAVATORY SET 1GLAL-C-R
Turn each cartridgeTurn each cartridge
splines intosplines into OFFOFF positionposition
before installing handlesbefore installing handles
Place handle on the spline.Place handle on the spline.
Flange Flange
BushingBushing
CUT THE SPLINE TO FITCUT THE SPLINE TO FIT
* 2 5/8˝ (67 mm)* 2 5/8˝ (67 mm)
from the nished wallfrom the nished wall
IF THE HANDLE DOES NOT FITIF THE HANDLE DOES NOT FIT
Tighten set screws to secure

1 5/8˝
4 1
1 7/8˝
WALL MOUNT LAVATORY SET 1GLAL-C-RWALL MOUNT LAVATORY SET 1GLAL-C-R
MUST CUT FLUSHMUST CUT FLUSH
TO THE FLANGE TRIMTO THE FLANGE TRIM
* 1 7/8˝ (47.5mm) * 1 7/8˝ (47.5mm)
from the nished wallfrom the nished wall
FlangeFlange
Pre-assembled Spout RingPre-assembled Spout Ring
* Cut the Slip-Fit Shank 1 5/8˝ long from the Cut the Slip-Fit Shank 1 5/8˝ long from the
nished wall and nished wall and MUST REMOVE ANY
BURRS before installing the Wall Spout.before installing the Wall Spout.
Tighten set screws to secure

WALL MOUNT LAVATORY SET 1GLAL-C-RWALL MOUNT LAVATORY SET 1GLAL-C-R
1GR1001GR100
Wall Mount Valve Wall Mount Valve
Rough-InRough-In
HLA04HLA04
Cross HandleCross Handle
HLA01HLA01
Lever HandleLever Handle
5
IF THE HANDLES DO NOT ALIGN CORRECTLYIF THE HANDLES DO NOT ALIGN CORRECTLY
You can adjust them. Please refer to the You can adjust them. Please refer to the
‘Handle Alignment’ instruction at the back.‘Handle Alignment’ instruction at the back.
Lock NutLock Nut