Rush Club smoke dual User manual

user manual
P/N 350100
4
1-B
READ AND SAVE THESE INSTRUCTIONS

2 Dimensions
Dimensions
All dimensions are in millimeters

Dimensions 3
© 2013-2015 Martin Professional ApS. Information subject to change without notice. Martin Professional and all
affiliated companies disclaim liability for any injury, damage, direct or indirect loss, consequential or economic loss or
any other loss occasioned by the use of, inability to use or reliance on the information contained in this manual. The
Martin logo, the RUSH by Martin logo, the RUSH by Martin name, the Martin name and all other trademarks in this
document pertaining to services or products by Martin Professional or its affiliates and subsidiaries are trademarks
owned or licensed by Martin Professional or its affiliates or subsidiaries.
Martin Professional • Olof Palmes Allé 18 • 8200 Aarhus N • Denmark • www.martin.com

4
Contents
Contents
Dimensions................................................................................................................................ 2
Contents..................................................................................................................................... 4
Safety information ...................................................................................................................... 5
Product overview ....................................................................................................................... 8
Product description................................................................................................................ 8
Features at a glance............................................................................................................... 8
Product details ....................................................................................................................... 9
Quick Start ............................................................................................................................... 12
Setting up ............................................................................................................................. 12
Making fog and haze............................................................................................................ 12
Installation and setting up........................................................................................................ 13
Location ............................................................................................................................... 13
AC power.............................................................................................................................. 13
Setting up ............................................................................................................................. 14
Final checks ......................................................................................................................... 16
Turning on the power ........................................................................................................... 16
Control settings........................................................................................................................ 17
Overview .............................................................................................................................. 17
Setting Fog Run modes........................................................................................................ 17
Setting output density for Fog heads ................................................................................... 17
Setting Haze Run modes...................................................................................................... 17
Setting output density for Haze heads.................................................................................. 18
Setting the Timer .................................................................................................................. 18
Setting the DMX base address............................................................................................. 18
Setting the master-slave link mode ...................................................................................... 18
Priming the system after fluid out ......................................................................................... 18
Priming system with Quick access buttons.......................................................................... 19
Resetting options to factory settings .................................................................................... 19
Remote control ........................................................................................................................ 21
Overview .............................................................................................................................. 21
Functions.............................................................................................................................. 21
Connection........................................................................................................................... 21
DMX control ............................................................................................................................. 23
Overview .............................................................................................................................. 23
Connection........................................................................................................................... 23
DMX functions ...................................................................................................................... 23
Fog fluid types ......................................................................................................................... 25
Basic service ........................................................................................................................... 26
Cleaning............................................................................................................................... 26
Fuse replacement................................................................................................................. 26
Troubleshooting....................................................................................................................... 27
Status messages...................................................................................................................... 28
Resetting the system after fluid out ...................................................................................... 28
Specifications .......................................................................................................................... 29

Safety information 5
Safety information
Read the safety precautions in this manual befor installing, operating or
servicing this product.
The following symbols are used to identify important safety information:
Caution! Safety
hazard. Risk of
severe injury or
death.
Caution! Burn
hazard. Hot
surface. Do not
touch.
Danger!
Hazardous
voltage. Contact
will cause electric
shock.
Caution! Fire
hazard.
Warning! This product is not for household use. It presents risks of injury due
to electric shock, burns, falls and respiratory problems!
Read this manual before operating the system, follow the safety precautions
listed below, and observe all warnings in this manual and printed on the system.
Use the system only as described in this manual and in accordance with local
laws and regulations.
If you have questions about how to operate the system safely, or if you have
followed the instructions in this manual and the system is malfunctioning, please
contact Martin Service.
Preventing electric shocks
•Always ground (earth) the system electrically.
•Use only a source of AC power that complies with local building and
electrical codes, and that has both overload and ground-fault protection.
•Before connecting the system to power, check that the voltage indicated
on the system’s serial label matches your local AC power voltage. If your
AC power voltage does not match, do not use the system. Contact Martin
Service for assistance.
•Before using the system, check that all power distribution equipment and
cables are in perfect condition and rated for the current requirements of
all connected devices.
•If the system or any cables connected to it are in any way damaged,
defective, wet, or show signs of overheating, stop using the system and
contact Martin Service for assistance. If the supply cord is damaged, it
must be replaced by a special cord or assembly available from the
manufacturer or its service agent.
•Disconnect the system from AC power before servicing and when not in
use.

6 Safety information
•This system is not waterproof and should not be exposed to wet outdoor
conditions. Do not immerse in water or any other liquid. Do not expose to
high-pressure water jets.
•Do not spill fluid over or inside the system. If fluid is spilled, disconnect
AC power and clean with a damp cloth. If fluid is spilled onto electronic
parts, take the system out of service and contact Martin for advice.
•Do not remove the covers or attempt to repair a faulty system. Refer any
service not described in this manual to Martin.
•Do not operate the system if any parts are damaged, defective or
missing.
•Moisture and electricity do not mix. Do not aim fog output at electrical
connections or devices.
Preventing burns and fire
•The fog produced by the system is hot enough to cause burns when it
leaves the nozzle, and very hot droplets of fluid escape occasionally.
Keep people and objects at least 60cm (24 inches) away from the fog
output nozzle.
•Do not touch the fog output nozzle during or after use – it becomes
extremely hot and remains hot for several hours after the system has
been shut down.
•Fog output contains glycol, a flammable alcohol that burns with an
almost invisible blue flame. Do not point fog output at sources of ignition
such as open flames or pyrotechnic effects.
•Do not attempt to bypass thermostatic switches, fluid sensors or fuses.
•Replace fuses only with ones of the type and rating specified in this
manual for the system.
•Provide a minimum free space of 100mm (4 inches) around the system.
•Provide a minimum free space of 500mm (20 inches) around fans and air
vents and ensure free and unobstructed air flow to and around the
system.
•Keep the system at least 60cm (24 inches) away from combustible and
heat-sensitive materials.
•Do not operate the system if the ambient temperature (Ta) is below 5° C
(41° F) or above 40° C (104° F).
•Do not operate the system if the relative air humidity exceeds 80%.
Preventing injuries
•Fasten the system securely to a fixed surface or structure when in use.
The system is not portable when installed.
•Ensure that any supporting structure and/or hardware used can hold at
least 10 times the weight of all the devices they support.
•If suspending from a rigging structure, fasten the system to a rigging
clamp. Do not use safety cables as the primary means of support.
•If the system is installed in a location where it may cause injury or
damage if it falls, install as directed in this manual a secondary
attachment such as a safety cable that will hold the system if a primary
attachment fails. The secondary attachment must be approved by an
official body such as TÜV as a safety attachment for the weight that it
secures, must comply with EN 60598-2-17 Section 17.6.6 and must be
capable of bearing a

Safety information 7
static suspended load that is ten times the weight of the system and all
installed accessories.
•Check that all external covers and rigging hardware are securely
fastened.
•Block access below the work area and work from a stable platform
whenever installing, servicing or moving the system.
•Do not operate the system with missing or damaged covers or shields.
•In the event of an operating problem, stop using the system immediately
and disconnect it from power. Do not attempt to use a system that is
obviously damaged.
•Do not modify the system in any way not described in this manual or
install other than genuine RUSH by Martin™ parts.
•Refer any service operation not described in this manual to a qualified
technician.
•Fog output can cause condensation. Do not point the output at smooth
floors. Floors and surfaces may become slippery. Check these frequently
and wipe dry as necessary to avoid any danger of slipping.
•Ensure at least 2 m visibility in areas where fog is being produced.
•Fog fluid contains food-grade glycols in solution but may present health
risks if swallowed. Do not drink it. Store it securely. If eye contact occurs,
rinse with water. If fluid is swallowed, give water and obtain medical
advice.
•This appliance is not intended for use by persons (including children)
with reduced physical sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for
their safety. Children should be supervised to ensure that they do not
play with the appliance.
Preventing breathing problems
•A system can operate safely only with the fog fluid it is designed for. Use
the system only with fluids specified under “Fog fluid options” on page
25 or you may cause the release of toxic gases, presenting a severe
health hazard. You will also probably damage the system.
•Do not create dense fog in confined or poorly ventilated areas.
•Do not expose people with health problems (including allergic and/or
respiratory conditions such as asthma) to fog output.
•Do not point fog output directly at a person’s face or at face height.
For the latest user documentation and other information for this and all Martin™
products, please visit the Martin website at http://www.martin.com
If you have any questions about how to install, operate or service the fixture
safely, please contact your Martin™ distributor (see www.martin.com/distributors
for details) or call the Martin™ 24-hour service hotline on [phone], or in
the USA on 1-888-tech-180.

8 Product overvie
w
Product overview
Product description
The RUSH Club Smoke Dual™ is a top of the range atmosphere system from
Martin Professional featuring multiple remote fog or haze heads with a base
pump/fluid unit. Its remote heads allow the base unit to be conveniently located
for fluid refill while the heads can be positioned in the ideal location for even
fogging or hazing of the venue.
Designed using the latest fog system technology, the RUSH Club Smoke Dual™
is capable of generating a variable level of fog or haze from up to 6 heads
controlled in pairs, which are connected using a simple push together fluid line
and a single control cable.
Congratulations on your purchase of the RUSH Club Smoke Dual™ from Martin.
Details of the full range of Martin products are available on our website at
www.martin.com.
Features at a glance
•1-6 Fog or Haze heads per system
•Flying/hanging brackets as standard
•Continuous output
•Water-based fluid with long hang time
•Low noise
•Lightweight
•Variable output control for each head pair using DMX
•10 liter (2.64 US gal.) fluid capacity
•“Out of Fluid” sensing utilizing pressure sensor
•Valved output connectors on pump unit
•On-board DMX 3-pin and 5-pin
•User-friendly on-board control panel
•Optional external fluid connection and Digital Remote Control
Use only Martin RUSH Club Smoke Dual Fluid™. Use of other fluid
will void warranty.

Product overvie
w
9
Control link
output to next
head
Control input
from pump
unit
Mains power
switch
Mains inlet
cable
Fluid pipe
connection
Heat (red) and
Ready (green)
indicators
Product details
Fog Head
Fog output
nozzle
WARNING!
High temperature
vapour and surfaces
If suspending overhead:
Loop safety cable under
hanging bracket and
secure

10 Product overvie
w
Control link
output to next
head
Control input
from pump
unit
Mains power
switch
Mains inlet
cable
Fluid pipe
connection
Heat (red) and
Ready (green)
indicators
Haze fan inlet
Haze Head
Haze output
port
WARNING!
High temperature
vapour and surfaces
If suspending overhead:
Loop safety cable under
hanging bracket and
secure