Rutland County Garden Furniture Premium Lean-to Pergola User manual

Assembly Instructions
Rutland Premium Lean-to
Pergola
1
Before you commence the assembly process we recommend that you read these instructions thoroughly beforehand to
familiarise yourself with the assembly process and to also check that you have the correct components. If for any reason you
need assistance, you can find our contact details on the final page of these instructions.
We highly recommend that any assembly is carried out on an open flat, level surface if possible with sufficient space. You will
also require the assistance of up to 2 adults to complete assembly safely.
Please note: 1) For a free-standing pergola you can remove up to 600mm from the bottom of each post prior to commencing
construction.
2) Wall fixings are not included.
Package contents
Tools required
Items/Quantities in brackets are for 3 post version
2 x Corner posts, (1 x Intermediate post)
1 x Runner
1 x Wall plate
6 x Rafters
4 (6) x Braces
8 (12) x Pedestal panels
32 (48) x 65mm screws
2 (4) x 75mm screws
2 x M6 200mm Coach screws
8 (12) x M8 100mm Coach screws
10 x M8 120mm Coach screws
8 and 10mm socket drive or spanner
#2 Pozidriv screwdriver
Platform or Step ladder
The Rutland Premium Lean-to Pergola

Rutland Premium Lean-to Pergola
Rutland County Garden Furniture Ltd, Ashbourne House, 2 Dovecote Meadows,
Aslackby, Sleaford, Lincs, NG34 0HZ.
Company No: 7670072 VAT No: 151744027
2
Step 1
Step 2
Check that you have the correct components as
shown in the package contents, including any fixings.
Your pergola can be shorter than standard by
removing the appropriate amount from the bottom
of each post. Remember to subtract the same
amount from the dimension shown in Step 2.
Take the wall plate and place it horizontally on the
wall where you would like the pergola located. Mark
the hole positions for your wall fixings then drill and
fix in place. Note: The distance from the underside of
the wall plate to the floor is 256cm.
Step 3
Step 4
Lay the two posts and the runner on the ground,
adjacent to the wall you intend to affix the pergola to
as shown...
...ensuring that the pre-drilled fixing hole in the post
is uppermost, the slots in the post and runner are
perfectly aligned and that the post is at a 90° angle to
the runner.

Rutland Premium Lean-to Pergola
Rutland County Garden Furniture Ltd, Ashbourne House, 2 Dovecote Meadows,
Aslackby, Sleaford, Lincs, NG34 0HZ.
Company No: 7670072 VAT No: 151744027
3
Step 5
Step 6
Secure each post to the runner with a 75mm screw.
Place a brace as shown, ensuring that the connecting
faces are flush with both post and runner...
Step 7
Step 8
...and centrally aligned on the underside of the
runner...
...and the the post. Now secure in place using a
100mm coach screw at each end. Repeat steps 6 -8
for the other end of the runner.

Rutland Premium Lean-to Pergola
Rutland County Garden Furniture Ltd, Ashbourne House, 2 Dovecote Meadows,
Aslackby, Sleaford, Lincs, NG34 0HZ.
Company No: 7670072 VAT No: 151744027
4
Step 9
Step 10
For a six post version line up the intermediate post
with the mid-point pencil lines on the runner, slot
into place, ensuring it is at 90° to the runner and fix in
place with 2 x 75mm screws. Attach a brace either
side of the post as before.
Using your assistants, lift the frame assembly into the
vertical position, aligned with the runner and
approximately the length of a rafter from the wall.
Step 11
Step 12
Now lift the first rafter into place, slotting each end
into the slot in the runner/post...
...and wall plate. (if the joint is tight use a mallet or
hammer with wood block to gently tap the rafter into
place).

Rutland Premium Lean-to Pergola
Rutland County Garden Furniture Ltd, Ashbourne House, 2 Dovecote Meadows,
Aslackby, Sleaford, Lincs, NG34 0HZ.
Company No: 7670072 VAT No: 151744027
5
Step 13
Step 14
Secure the rafter to the wall plate with a 120mm
coach screw driven in from above....
..and into the runner/post using a 200mm coach
screw.
Step 15
Step 16
Repeating steps 10 - 13, add the second rafter at the
opposite end of the assembly.
Now add the remaining rafters, securing each one
with a 120mm coach screw at both ends.

Rutland Premium Lean-to Pergola
Rutland County Garden Furniture Ltd, Ashbourne House, 2 Dovecote Meadows,
Aslackby, Sleaford, Lincs, NG34 0HZ.
Company No: 7670072 VAT No: 151744027
6
Step 17
Step 18
Add the remaining braces between the posts and
rafters, using the same method as before.
Finally attach a pedestal panel to each face of the
posts, aligning them with the post and securing each
panel with 4 x 65mm screws.
Step 19
Your Rutland Premium Lean-to Pergola is now
complete.
We hope that you found your product quick and easy to assemble but if not and you require any
further assistance or have any questions you can contact us by telephone on: 01778 440803
Email: [email protected]
www.rutlandcountygardenfurniture.co.uk