Attaching the PCS
Connector:
2
31
Screw the PCS-Boom Connector on to the male
3/8”thread of the boom pole, in a clockwise rotation/
direction - to the desired position.
PCS-Boom Connector
Quick Start Guide
PCS-Boom Connector
4
To tighten connection, use a screw driver (not supplied),
and insert this through the circular hole in the tip, as shown.
Turn clockwise to tighten rmly (do not over-tighten).
5
6
Screw the PCS‘tip’into the female 3/8”thread of your
windshield, shock mount, or other accessory that you
would like to use with your PCS-Boom Connector.
To attach the two components, simply line up the tip
with the Connector and push the tip in to lock it.
You will hear a ‘click’as it locks together!
Use the included hex/Allen key to tighten the two small
locking screws on the PCS-Boom Connector. This will lock
it on to the 3/8”boom pole thread, without damaging it.
To release, pull down the grey outer collar on the
PCS-Boom Connector, as shown.
Quick Start Guide
PCS-Boom Connector (185801)
Thank you for choosing the
Rycote PCS-Boom Connector!
This guide provides you with
the basics to get you started.
Full details about this product are available on
our website: rycote.com/microphone-windshield-
shock-mount/pcs-boom-range/
Optional attachments
The following attachments are available
for the PCS-Boom Connector:
• Pair of 3/8”Tips
for PCS-Boom Connector (185805)
• Classic Adaptor
for PCS-Boom Connector (185807)
• Cyclone Adaptor
for PCS-Boom Connector (185808)
1
PCS-Boom Connector, PCS-Lite
and PCS-Utility – connect to a male
3/8”thread in a clockwise rotation.
PCS-Spigot – connect to a 5/8”
(16mm) male spigot and use the includ-
ed hex key to fully secure connection as
shown above.
2
31
Screw the PCS-Boom Connector on to the male
3/8”thread of the boom pole, in a clockwise rotation/
direction - to the desired position.
PCS-Boom Connector
Quick Start Guide
PCS-Boom Connector
4
To tighten connection, use a screw driver (not supplied),
and insert this through the circular hole in the tip, as shown.
Turn clockwise to tighten rmly (do not over-tighten).
5
6
Screw the PCS‘tip’into the female 3/8”thread of your
windshield, shock mount, or other accessory that you
would like to use with your PCS-Boom Connector.
To attach the two components, simply line up the tip
with the Connector and push the tip in to lock it.
You will hear a ‘click’as it locks together!
Use the included hex/Allen key to tighten the two small
locking screws on the PCS-Boom Connector. This will lock
it on to the 3/8”boom pole thread, without damaging it.
To release, pull down the grey outer collar on the
PCS-Boom Connector, as shown.
Quick Start Guide
PCS-Boom Connector (185801)
Thank you for choosing the
Rycote PCS-Boom Connector!
This guide provides you with
the basics to get you started.
Full details about this product are available on
our website: rycote.com/microphone-windshield-
shock-mount/pcs-boom-range/
Optional attachments
The following attachments are available
for the PCS-Boom Connector:
• Pair of 3/8”Tips
for PCS-Boom Connector (185805)
• Classic Adaptor
for PCS-Boom Connector (185807)
• Cyclone Adaptor
for PCS-Boom Connector (185808)
PCS-Boom Connector & PCS-Utility
Use included hex key to tighten the two
small locking screws on the connector,
providing a extra secure connection.
PCS-Organizer –
connect to a at
surface, using washers (included) and suit-
able screws (not included).When mounting
vertically always position so that screws are
aligned one above another, as shown above.
WARNING: Mounting screws are not
included. Always use washers included.
Do NOT use countersunk screws.
Recommended screw size: M4 15mm
2
