Ryobi LCDI1802 User manual

GB
18 VOLT COMPACT HAMMER DRILL DRIVER USER’S MANUAL 1
FR
PERCEUSE/VISSEUSE COMPACTE À PERCUSSION 18 VOLTS MANUEL D’UTILISATION 6
DE
18 VOLT KOMPAKT SCHLAGBOHRSCHRAUBER BEDIENUNGSANLEITUNG 12
ES
ROTOMARTILLO/TALADRO/DESTORNILLADOR DE 18 VOLT MANUAL DE UTILIZACIÓN 19
IT
TRAPANO A PERCUSSIONE COMPATTO DA 18 VOLT MANUALE D’USO 25
NL
18 VOLT COMPACTE HAMERBOORMACHINE GEBRUIKERSHANDLEIDING 31
PT
MARTELO PERFURADOR COMPACTO DE 18 VOLTS MANUAL DE UTILIZAÇÃO 37
DK
KOMPAKT 18 VOLT SLAGBORE-/SKRUEMASKINE BRUGERVEJLEDNING 43
SE
18 VOLT KOMPAKT SLAGBORRMASKIN INSTRUKTIONSBOK 49
FI
18 VOLTIN KOMPAKTI ISKUPORAKONE KÄYTTÄJÄN KÄSIKIRJA 55
NO 18-VOLT KOMPAKT SLAGDRILL BRUKSANVISNING 60
RU КОМПАКТНАЯ УДАРНАЯ ДРЕЛЬ-ШУРУПОВЕРТ, 18 ВОЛЬТ êìäéÇéÑëíÇé èé ùäëèãìÄíÄñàà 65
PL PODRĘCZNA WIERTARKO-WKRĘTARKA UDAROWA 18 V INSTRUKCJA OBSŁUGI 71
CZ 18 VOLTOVÝ KOMPAKTNÍ PŘÍKLEPOVÝ VRTACÍ ŠROUBOVÁK NÁVOD K OBSLUZE 77
HU 18 VOLTOS KOMPAKT ÜTVEFÚRÓ-CSAVARBEHAJTÓ HASZNÁLATI ÚTMUTATÓ 83
RO CIOCAN PERFORATOR COMPACT 18 VOLŢI MANUAL DE UTILIZARE 89
LV 18 V KOMPAKTAIS PERFORATORS/SKRŪVGRIEZIS LIETOTĀJA ROKASGRĀMATA 95
LT 18 V KOMPAKTINIS PLAKTUKAS / GRĄŽTAS / SUKTUVAS NAUDOJIMO VADOVAS 101
EE KOMPAKTLÖÖKTRELL-KRUVIKEERAJA 18 VOLTI KASUTAJAJUHEND 106
HR KOMPAKTNA UDARNA BUŠILICA OD 18 V KORISNI»KI PRIRU»NIK 111
SI 18-VOLTNI KOMPAKTNI UDARNI VRTALNIK UPORABNIŠKI PRIROČNIK 116
SK 18 V KOMPAKTNÉ VŔTACIE KLADIVOSO SKRUTKOVAČOM NÁVOD NA POUŽITIE 121
GR COMPACT ΣΦΥΡΟ-ΔΡΕΠΑΝΟΚΑΤΣΑΒΙΔΟ 18 VOLT ΟΔΗΓΙΕΣ ΧΡΗΣΗΣ 127
TR 18 VOLT KOMPAKT DARBELİ MATKAP TORNAVİDA KULLANiM KILAVUZU 133
LCDI1802
GB ORIGINAL INSTRUCTIONS FR TRADUCTION DES INSTRUCTIONS ORIGINALES DE ÜBERSETZUNG DER ORIGINALANLEITUNG ES TRADUCCIÓN
DE LAS INSTRUCCIONES ORIGINALES IT TRADUZIONE DELLE ISTRUZIONI ORIGINALI NL VERTALING VAN DE ORIGINELE INSTRUCTIES PT TRADUÇÃO
DAS INSTRUÇÕES ORIGINAIS DK OVERSÆTTELSE AF DE ORIGINALE INSTRUKTIONER SE ÖVERSÄTTNING AV DE URSPRUNGLIGA INSTRUKTIONERNA
FI ALKUPERÄISTEN OHJEIDEN SUOMENNOS NO OVERSETTELSE AV DE ORIGINALE INSTRUKSJONENE RU ПЕРЕВОД ОРИГИНАЛЬНЫХ ИНСТРУКЦИЙ PL TŁUMACZENIE
INSTRUKCJI ORYGINALNEJ CZ PŘEKLAD ORIGINÁLNÍCH POKYNŮ HU AZ EREDETI ÚTMUTATÓ FORDÍTÁSA RO TRADUCEREA INSTRUCŢIUNILOR ORIGINALE LV TULKOTS NO
ORIĢINĀLĀS INSTRUKCIJAS LT ORIGINALIŲ INSTRUKCIJŲ VERTIMAS EE ORIGINAALJUHENDI TÕLGE HR PRIJEVOD ORIGINALNIH UPUTA SI PREVOD ORIGINALNIH NAVODIL
SK PREKLAD POKYNOV VORIGINÁLI GR μΕΤΑΦΡΑΣΗ ΤΩΝ ΠΡΩΤΟΤΥΠΩΝ ΟΔΗΓΙΩΝ TR ORIJINAL TALIMATLARIN TERCÜMESI

Fig. 1
Fig. 2
6
13
14
10
11
12
15
Fig. 3
17
18
16
9
7
31
33 32
12
34
7
9
8
5
6

Fig. 4
Fig. 5
Fig. 6
5
8
19
20
21
22
23
41
4
24
25
LO
HI
26 27 28
3
29
2
30
21
22 41
35
23
26 27
28
Fig. 9
Fig. 8
Fig. 7

13
636
34
35
6
I
39
38
40 37
Fig. 10
961067241-01_EU.indd A3 6/24/09 3:27:23 PM

Important! It is essential that you read the instructions in this manual before operating this machine.
Attention ! Il est indispensable que vous lisiez les instructions contenues dans ce manuel avant la mise en service
de l’appareil.
Achtung! Bitte lesen Sie unbedingt vor Inbetriebnahme die Hinweise dieser Bedienungsanleitung.
¡Atención! Es imprescindible que lea las instrucciones de este manual antes de la puesta en servicio.
Attenzione! Prima di procedere alla messa in funzione, è indispensabile leggere attentamente le istruzioni contenute
nel manuale.
Let op ! Het is van essentieel belang dat u de instructies in deze gebruiksaanwijzing leest vooraleer u dit toestel
in gebruik neemt.
Atenção! É indispensável que leia as instruções deste manual antes de utilizar a máquina.
OBS! Denne brugsanvisning skal læses igennem inden ibrugtagning.
Observera! Det är nödvändigt att läsa instruktionerna i denna bruksanvisning innan användning.
Huomio! On ehdottoman välttämätöntä lukea tässä käyttöohjeessa annetut ohjeet ennen käyttöönottoa.
Advarsel! Det er meget viktig at du leser denne brukerveiledningen før du tar maskinen i bruk.
ÇÌËχÌËe! èee‰ Ò·ÓÍÓÈ Ë Á‡ÔÛÒÍÓÏ ËÌÒÚÛÏeÌÚ‡ ÌeÓ·ıÓ‰ËÏÓ ÔÓ˜eÒÚ¸ ËÌÒÚÛ͈ËË ËÁ ̇ÒÚÓfl˘e„Ó
ÛÍÓ‚Ó‰ÒÚ‚‡.
Uwaga! Przed przystąpieniem do użytkowania tego urządzenia, należy koniecznie zapoznaćsięz zaleceniami
zawartymi w niniejszym podręczniku.
Důležité upozornění! Nepoužívejte tento přístroj dříve, než si přečtete pokyny uvedené v tomto návodu.
Figyelem! Feltétlenül fontos, hogy a jelen használati útmutatóban foglalt előírásokat az üzembe helyezés előtt
elolvassa!
Atenţie! Este esenţial săcitiţi instrucţiunile din acest manual înainte de operarea acestui aparat.
Uzmanību! Svarīgi, lai jūs pirms mašīnas darbināšanas izlasītu instrukcijas šajā rokasgrāmatā.
Dėmesio! Prieš pradėdami eksploatuoti šį prietaisą, svarbu, kad perskaitytumėte šiose instrukcijose pateiktus
nurodymus.
Tähtis! Enne trelli kasutama hakkamist tuleb käesolevas juhendis esitatud juhised kindlasti läbi lugeda.
Upozorenje! Neophodno je da pročitate ove upute prije uporabe ovog uređaja.
Pomembno! Pred uporabo tega stroja, obvezno preberite navodila iz tega priročnika.
Dôležité! Pre prácou s týmto zariadením je dôležité, by ste si prečítali pokyny v tomto návode.
Προσοχή! Είναι απαραίτητο να διαβάσετε τις συστάσεις των οδηγιών αυτών πριν και τη θέση σε
λειτουργία.
Dikkat! Cihazın çalıştırılmasından önce bu kılavuzda bulunan talimatlarıokumanız zorunludur.
Subject to technical modifications / Sous réserve de modifications techniques /Technische Änderungen vorbehalten /
Sujeto a modificaciones técnicas / Con riserva di eventuali modifiche tecniche /Technische wijzigingen voorbehouden /
Com reserva de modificações técnicas / Med forbehold for tekniske ændringer / Med förbehåll för tekniska ändringar /
Tekniset muutokset varataan / Med forbehold om tekniske endringer / åÓ„ÛÚ ·˚Ú¸ ‚ÌeÒeÌ˚ ÚeıÌ˘eÒÍËe ËÁÏeÌeÌËfl /
Z zastrzeżeniem modyfikacji technicznych / Změny technických údajůvyhrazeny / A műszaki módosítás jogát fenntartjuk /
Sub rezerva modificaţiilor tehnice / Paturam tiesības mainīt tehniskos raksturlielumus / Pasiliekant teisę daryti techninius pakeitimus /
Tehnilised muudatused võimalikud /Podloæno tehniËkim promjenama /Tehnične spremembe dopuščene/
Technické zmeny vyhradené / Υπό την επιφύλαξη τεχνικών τροποποιήσεων / Teknik değişiklik hakkısaklıdır
961067241-01_EU.indd A3 6/24/09 3:27:23 PM

1
English
GB
FR DE ES IT NL PT DK SE FI NO RU PL CZ HU RO LV LT EE HR SI SK GR TR
SPECIAL SAFETY RULES
■Wear ear protectors. Exposure to noise can cause
hearing loss.
■Use auxiliary handle(s), if supplied with the tool.
Loss of control can cause personal injury.
■Hold power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring. Cutting
accessory contacting a «live» wire may make exposed
metal parts of the power tool «live» and could give the
operator an electric shock.
ASSEMBLY
AUXILIARY HANDLE ASSEMBLY
See Figure 2.
An auxiliary handle is packed with the drill for ease of
operation and to help prevent loss of control. The handle
can be mounted on the opposite side for left or right hand
use.
■Insert handle screw into hole located above trigger
switch and seat hex head into hole.
■Slide handle collar onto screw, seat hex end of collar
into hex hole. Hex hole for depth stop rod should be
on top of collar.
■Slide depth stop rod into hex shaped hole on top of
collar.
■Slide depth guide clamp into notch in collar. Clamp
holds depth rod firmly in place.
NOTE: When properly installed, the teeth on the depth
stop rod should be aligned with the teeth indicator on the
depth stop rod clamp.
■Thread auxiliary handle onto screw and secure tightly.
NOTE: Be sure the auxiliary handle is securely tightened
against the depth stop rod clamp. This secures the depth
stop rod at the desired depth of cut. It also secures the
auxiliary handle.
DESCRIPTION
1. Keyless chuck
2. Torque adjustment ring
3. Quick mode selector
4. Two-speed gear train
5 . Rotation selector (forward/reverse/center lock)
6. Depth rod stop
7. Bit storage
8. Switch trigger
9. Mag Tray™
10. Handle screw
11. Hex head hole
12. Handle coller
13. Teeth
14. Depth stop rod clamp
15. Auxiliary handle
16. Battery pack (Not included)
17. Latches
18. Depress latches to release battery pack
19. Reverse
20. Forward
21. Chuck jaws
22. Lock (tighten)
23. Unlock (release)
24. Low speed
25. High speed
26. Drive mode
27. Drill mode
28. Hammer mode
29. To increase torque
30. To decrease torque
31. Bit
32. Screws
33. Bit holder
34. Drilling depth
35. Drill bit
36. Scale
37. To increase drilling depth
38. To loosen
39. To tighten
40. To decrease drilling depth
41. Chuck sleeve
SPECIFICATIONS
Voltage 18 V
Chuck 2-13 mm
Switch Variable speed
No load speed (Drill mode):
-Lo speed 0-400 min-1
-Hi speed 0-1500 min-1
Hammer speed (Blows per minute):
-Lo speed 0-5200 min-1
-Hi speed 0-19500 min-1
Max. torque 49 Nm
Weight (not incl. battery pack) 1.68 Kg
LCDI1802
BPL-1820
BPL-1815
BCL-1800
BCS618
BCL1418
BPP-1815
BPP-1815M
BPP-1817
BPP-1817M
BC-1815S
BC-1800
BCL-1800
BCS618
BCL1418
BCL14181H
BCL14183H
BCL14181H
BCL14183H
MODEL
BATTERY
PACK
(not included)
COMPATIBLE
CHARGER
(not included)

2
English
GB
FR DE ES IT NL PT DK SE FI NO RU PL CZ HU RO LV LT EE HR SI SK GR TR
OPERATION
WARNING
Do not allow familiarity with products to make you
careless. Remember that a careless fraction of a
second is sufficient to inflict serious injury.
WARNING
Always wear safety goggles or safety glasses
with side shields when operating products. Failure
to do so could result in objects being thrown into
your eyes, resulting in possible serious injury.
WARNING
Do not use any attachments or accessories
not recommended by the manufacturer of this
product. The use of attachments or accessories
not recommended can result in serious personal
injury.
APPLICATIONS
You may use this product for the purposes listed below:
■Drilling in all types of wood products (lumber, plywood,
panelling, composition board, and hard board)
■Drilling in ceramics, plastics, fiberglass, and laminates
■Drilling in metals
■Driving screws
■Hammer drilling in concrete, brick, or other masonry
This product will accept RYOBI One+ 18 V lithium-ion
battery packs and RYOBI One+ 18 V nickel-cadmium
battery packs.
BATTERY PROTECTION FEATURES
RYOBI 18 V lithium-ion batteries are designed with
features that protect the lithium-ion cells and maximize
battery life. Under some operating conditions, these
built-in features may cause the battery and the tool it is
powering to act differently from nickel-cadmium batteries.
During some applications, the battery electronics may
signal the battery to shut down, and cause the tool to
stop running. To reset the battery and tool, release the
trigger and resume normal operation.
NOTE: To prevent further shut down of the battery, avoid
forcing the tool.
If releasing the trigger does not reset the battery and
tool, the battery pack is depleted. If depleted, the battery
pack will begin charging when placed on the lithium-ion
charger.
TO INSTALL BATTERY PACK
See Figure 3.
■Lock the switch trigger by placing the rotation selector
in the center position.
■Place the battery pack on the tool.
■Make sure the latches on each side of the battery
pack snap into place and the battery pack is secured
on the tool before beginning operation.
WARNING
Always remove battery pack from your tool when
you are assembling parts, making adjustments,
cleaning, or when not in use. Removing battery
pack will prevent accidental starting that could
cause serious personal injury.
TO REMOVE BATTERY PACK
See Figure 3.
■Lock the switch trigger by placing the rotation selector
in the center position.
■Depress the latches on the side of battery pack.
■Remove the battery pack from the tool.
WARNING
Battery tools are always in operating condition.
Therefore, switch should always be locked when
not in use or carrying at your side.
SWITCH TRIGGER
See Figure 4.
■To turn the drill ON, depress the switch trigger.
■To turn it OFF, release the switch trigger.
VARIABLE SPEED
The variable speed switch trigger delivers higher speed
and torque with increased trigger pressure and lower
speed with decreased trigger pressure.
NOTE: You might hear a whistling or ringing noise from
the switch during use. Do not be concerned; this is a
normal part of the switch function.
ROTATION SELECTOR
(FORWARD/REVERSE/CENTER LOCK)
See Figure 4.
The bit rotation is reversible and is controlled by a
selector located above the switch trigger. With the drill
held in normal operating position, the rotation selector
should be positioned to the left of the switch trigger for
forward drilling. The drilling direction is reversed when the
selector is to the right of the switch trigger.
Setting the switch trigger in the OFF (center lock) position
helps reduce the possibility of accidental starting when
not in use.
CAUTION:
To prevent gear damage, always allow the chuck
to come to a complete stop before changing the
direction of rotation.
To stop the drill, release the switch trigger and allow the
chuck to come to a complete stop.

3
English
GB
FR DE ES IT NL PT DK SE FI NO RU PL CZ HU RO LV LT EE HR SI SK GR TR
OPERATION
NOTE: The drill will not run unless the rotation selector is
pushed fully to the left or right.
Avoid running the drill at low speeds for extended periods
of time. Running at low speeds under constant usage
may cause the drill to become overheated. If this occurs,
cool the drill by running it without a load and at full speed.
INTERNAL SPINDLE LOCK
The internal spindle lock allows the user single-handed
control of chuck adjustments and bit changes. Squeezing
the chuck body stops the chuck jaws from turning. For
bit changes and chuck adjustments, squeeze the chuck
body and turn.
KEYLESS CHUCK
See Figure 5.
The drill has a keyless chuck to tighten or release drill
bits in the chuck jaws. The arrows on the chuck indicate
which direction to rotate the chuck body in order to LOCK
(tighten) or UNLOCK (release) the drill bit.
WARNING
Do not hold the chuck with one hand and use the
power of the drill to tighten the chuck jaws on the
drill bit. The chuck body could slip in your hand,
or your hand could slip and come in contact with
the rotating drill bit. This could cause an accident
resulting in serious personal injury.
TWO-SPEED GEAR TRAIN (HI-LO)
See Figure 6.
The drill has a two-speed gear train designed for drilling
or driving at LO (1) or HI (2) speeds. A slide switch is
located on top of the drill to select either LO (1) or HI (2)
speed. When using drill in the LO (1) speed range, speed
will decrease and unit will have more power and torque.
When using drill in the HI (2) speed range, speed will
increase and unit will have less power and torque. Use
LO (1) speed for high power and torque applications and
HI (2) speed for fast drilling or driving applications.
NOTE: If you have difficulty changing from one gear
range to the other, turn the chuck by hand until the gears
engage.
CAUTION:
Never change gears while the tool is running.
Failure to obey this caution could result in serious
damage to the drill.
QUICK MODE SELECTOR
See Figure 7.
The Quick Mode Selector allows you to quickly switch
from drill mode to drive mode.
In general, drill mode should be used for drilling and
other heavy duty applications. Drive mode should be
used for driving screws.percussion mode should be used
for impact drilling.
SELECTING DRIVE OR DRILL SETTING
See Figure 6-7.
Using the chart below, choose correct speed and mode
the type of bit, fastener, and material you will be using.
■Choose your APPLICATION
■Choose the correct SPEED: (1/LOW or 2/HIGH)
■Choose the correct MODE: (DRIVE, DRILL, OR
HAMMER)
1. APPLICATION 2. SPEED 3. MODE
• Lag screws up to 9.5 mm dia. by 38.1 mm long
• Hole saw up to 50.8 mm
• Spade bits up to 38.1 mm
• Drill bits up to 12.7 mm
• Drilling into metal
• Concrete screws
1/LOW DRILL MODE
(TORQUE ADJUSMENT NOT ACTIVE)
2/HIGH
• Drill bits up to 6.4 mm
• Deck or wood screws up to 63.5 mm long
• Self tapping screws
1/LOW DRIVE MODE
• Deck or wood screws up to 63.5 mm long
• Small screws or delicate work that requires more control 2/HIGH
• Masonry bit up to 12.7 mm
1/LOW HAMMER MODE
(TORQUE ADJUSMENT NOT ACTIVE)
2/HIGH

4
English
GB
FR DE ES IT NL PT DK SE FI NO RU PL CZ HU RO LV LT EE HR SI SK GR TR
OPERATION
TORQUE ADJUSTMENT
See Figure 8.
When using the drill-driver for various driving applications,
it becomes necessary to increase or decrease the torque
in order to help prevent the possibility of damaging
screw heads, threads, workpiece, etc. In general, torque
intensity should correspond to the screw diameter. If the
torque is too high or the screws too small, the screws
may be damaged or broken.
The torque is adjusted by rotating the torque adjustment ring.
The torque is greater when the torque adjustment ring
is set on a higher setting. The torque is less when the
torque adjustment ring is set on a lower setting.
The proper setting depends on the type of material and
the size of screw you are using.
BIT STORAGE
See Figure 3.
When not in use, bits provided with the drill can be placed
in the storage areas located on the base of the drill.
MAG TRAY™
See Figure 3.
The magnetic tray conveniently stores screws or other
small parts.
ADJUSTING THE AUXILIARY HANDLE ASSEMBLY
AND DEPTH STOP ROD
See Figure 10.
An auxiliary handle is packed with the drill for ease of
operation and to help prevent loss of control. The handle can
be mounted on the opposite side for left or right hand use.
To adjust the auxiliary handle assembly:
■Loosen the handle assembly by turning the handle
counterclockwise.
■Insert the auxiliary handle assembly in the desired
operating position.
■Securely tighten by turning the auxiliary handle
clockwise.
NOTE: Be sure the auxiliary handle is securely tightened
against the depth stop rod clamp. This secures the depth
stop rod at the desired depth of cut. It also secures the
auxiliary handle.
The depth stop rod helps control the depth of drilled
holes. For convenience and ease of starting threads, the
hex nut has been trapped inside the molded slot in the
auxiliary handle.
To adjust the depth stop rod:
■Lock the switch trigger by placing the rotation selector
in the center position.
■Loosen the auxiliary handle assembly by turning the
knob counterclockwise.
■Adjust the depth stop rod so that the drill bit extends
beyond the end of the rod to the required drilling
depth.
■Tighten the auxiliary handle assembly by turning the
knob clockwise.
NOTE: When properly installed, the teeth on the depth
stop rod should be aligned with the teeth indicator on the
depth stop rod clamp.
INSTALLING BITS
See Figure 9.
■Lock the switch trigger by placing the rotation selector
in the center position.
■Open or close the chuck jaws to a point where the
opening is slightly larger than the bit size you intend
to use. Also, raise the front of the drill slightly to keep
the bit from falling out of the chuck jaws.
■Insert the drill bit.
■Tighten the chuck jaws on the drill bit.
WARNING:
Make sure to insert the drill bit straight into the
chuck jaws. Do not insert the drill bit into the
chuck jaws at an angle then tighten. This could
cause the drill bit to be thrown from the drill,
resulting in possible serious personal injury or
damage to the chuck.
NOTE: Rotate the chuck body in the direction of the
arrow marked LOCK to tighten the chuck jaws. Do not
use a wrench to tighten or loosen the chuck jaws.
REMOVING BITS
See Figure 9.
■Lock the switch trigger by placing the rotation selector
in the center position.
■Open the chuck jaws.
NOTE: Rotate the chuck body in the direction of the
arrow marked UNLOCK to loosen the chuck jaws. Do
not use a wrench to tighten or loosen the chuck jaws.
■Remove the drill bit.
DRILLING
■Check the rotation selector for the correct setting
(forward or reverse).
■Secure the material to be drilled in a vise or with
clamps to keep it from turning as the drill bit rotates.
■Hold the drill firmly and place the bit at the point to be
drilled.

5
English
GB
FR DE ES IT NL PT DK SE FI NO RU PL CZ HU RO LV LT EE HR SI SK GR TR
OPERATION
■Depress the switch trigger to start the drill.
■Move the drill bit into the workpiece, applying only
enough pressure to keep the bit cutting. Do not force
the drill or apply side pressure to elongate a hole. Let
the tool do the work.
WARNING:
Be prepared for binding at bit breakthrough.
When these situations occur, drill has a tendency
to grab and kick opposite to the direction of
rotation and could cause loss of control when
breaking through material. If not prepared, this
loss of control can result in possible serious
injury.
■When drilling hard, smooth surfaces, use a center
punch to mark the desired hole location. This will
prevent the drill bit from slipping off-center as the hole
is started.
■When drilling metals, use a light oil on the drill bit to
keep it from overheating. The oil will prolong the life of
the bit and increase the drilling action.
■If the bit jams in the workpiece or if the drill stalls,
stop the tool immediately. Remove the bit from the
workpiece and determine the reason for jamming.
NOTE: This drill has an electric brake. When the switch
trigger is released, the chuck stops turning. When the
brake is functioning properly, sparks will be visible
through the vent slots on the housing. This is normal and
is the action of the brake.
MAINTENANCE
WARNING
When servicing, use only identical RYOBI
replacement parts. Use of any other parts may
create a hazard or cause product damage.
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use.
Use clean cloths to remove dirt, dust, oil, grease, etc.
WARNING
Do not at any time let brake fluids, gasoline,
petroleumbased products, penetrating oils, etc.,
come in contact with plastic parts. Chemicals can
damage, weaken or destroy plastic which may
result in serious personal injury.
Do not abuse power tools. Abusive practices can damage
tool as well as workpiece.
WARNING
Do not attempt to modify this tool or create
accessories not recommended for use with this
tool. Any such alteration or modification is misuse
and could result in a hazardous condition leading
to possible serious personal injury.
ENVIRONMENTAL PROTECTION
Recycle raw materials instead of disposing
as waste. The machine, accessories and
packaging should be sorted for
environmental-friendly recycling.
SYMBOLS
Safety Alert
V Volts
min-1 Revolutions or reciprocations per minute
Direct current
CE Conformity
Please read the instructions carefully before
starting the machine.
Recycle unwanted
Waste electrical products should not be
disposed of with household waste. Please
recycle where facilities exist. Check with your
Local Authority or retailer for recycling advice.