S.R.Smith Single Post Basketball Game Instruction manual

SINGLE POST
BASKETBALL GAME
CORPORATE HEADQUATERS
WESTERN SALES AND MANUFACTURING PLANT
P.O. Box 400 •1017 SW Berg Parkway
Canby, Oregon 97013
[phone] •[phone]
www.srsmith.com
06-447 ©S.R. SMITH, LLC 2005 JUN 07
ASSEMBLY AND INSTALLATION
INSTRUCTIONS

2
INTRODUCTION
The Single Post Basketball Game is designed for use on in-ground pools in shallow water depth areas.
Proper and complete assembly, use and supervision is essential for proper operation and to reduce the
risk of accident or injury.
**IMPORTANT**
Check entire boxes and inside all packing materials for parts. Before beginning assembly, read the
instructions and identify parts using the figures and parts listed in this document. It is critical that all
parts be carefully inspected by the installer prior to installation to ensure that no damage occurred in
transit and that a damaged part is not used. Proper installation cannot be overstressed, as an improper
installation voids S.R. Smith’s warranty and may affect the safety of the user.
Figure 1

3
SINGLE POST BASKETBALL PARTS LIST
ASSEMBLY INSTRUCTIONS
1. Begin by locating the frame assembly and the
horizontal support tube as shown in FIGURE 1.
Attach the horizontal support tube to the frame
assembly with the stainless steel split tees and
hardware as shown in FIGURE 2
2. Align the two holes in the top of the backboard with the
holes in the horizontal support tube as shown in FIGURE 3 .
Insert the 5/16” x 4” cairrage bolts into each hole in the
backboard and through the horizontal support tube. Thread
a hex nut onto the end of the carriage bolt that passes
through the backside of the horizontal support tube. Do not
tighten the hex nuts all the way down at this point.
ITEM # PART # DESCRIPTION QTY.
1 20-185 Frame Assembly 1 ea.
2 7-182 Horizontal Support Tube 1 ea.
3 2019061 Split “T” Half 2 ea.
4 2020049 3/8”-16 x 2 1/2" S/S Carriage Bolt 2 ea.
5 5-139 3/8”-16 Hex Nut S/S 2 ea.
6 5-309 5/16”-18 x 2 1/2” Hex Head Flange Bolt 4 ea.
7 05-33-114 7/16” x 1” Flat Washer 8 ea.
8 SPG-104A Basketball Rim, Backboard (and Net Not Shown) 1 ea.
9 05-33-115 5/16”-18 Hex Flange Nut 4 ea.
10 5-310 5/16”-18 x 4” Carriage Bolt S/S 2 ea.
11 2022650 5/16”-18 Hex Nut S/S 2 ea.
12 4-102 Expandable Collar, Anodized Aluminum 1 ea.
13 5-109 1/4”-20 x 1/2" BTNHD Cap Screw 1 ea.
14 5-108 1/4”-20 x 1/4" Nylon Tipped Set Screw 2 ea.
15 AS-100D / 100P Anchor Socket, 1.90” Diameter x 6” Deep
(Either the Plastic Or Bronze anchor are used for this assembly) 1 ea.
FIGURE 2
FIGURE 3

4
3. To install the rim to the backboard; align the four holes on the
rim mounting plate with the holes in the backboard as shown in
FIGURE 4. Insert the 5/16” x 2 1/2" bolts through the rim
mounting plate, backboard and frame mounting plate. Be sure
that there are washers between the bolt heads and the rim
mounting plate. Place washers onto the ends of the bolts that
pass through the frame mounting plate. Thread the hex flange
nuts onto the ends of the bolts.
4. Now that all of the bolts and nuts are in place, go through
and fully tighten all hardware components in the assembly.
5. The Single Post Basketball units are to be
anchored to the deck using a 6-inch deep AS-
100D anchor socket or the AS-100P plastic
anchor socket, with tightening bolt. Install the
anchor in the pool deck 12 inches back from the
pool’s edge as shown in FIGURE 5. Properly
bond the anchor socket using the attached
bonding screw and the appropriate bonding wire
per local codes. Allow concrete to cure before
installing Single Post Basketball Unit.
6. Each anchor socket has a removable cap, which needs to be removed before inserting the assembly.
The cap can be removed by inserting a small flat blade screwdriver into the groove between the anchor
socket and the cap and prying up. Place the basketball assembly into the anchor socket installed in the
pool deck. For the AS-100P’s use a 1/2” wrench to tighten post into place. If you have the AS-100D
installed, use a 1/8” Allen wrench to tighten the set screws in the expandable collar until the frame will no
longer rotate in the anchor socket. NOTE: When removing the basketball assembly from the anchors
make sure to place the caps in the anchors.
SAFETY INSTRUCTIONS
•This equipment is intended for use in shallow water depth areas.
•During play, do not wear jewelry (rings, watches, necklaces, etc.) Objects
may entangle in net.
•Do not dive or jump from any part of unit, including backboard support
braces or rim.
•Periodically inspect the rim, backboard and posts to assure there are no
worn parts and that all hardware is properly tightened.
FIGURE 5
FIGURE 4

5
VOLLEYBALL/BASKETBALL COMBINATION INSTALLATION
1) The Volleyball/Basketball game combination requires the installation of two AS-100P anchor
sockets into the pool deck. Install the anchors in the pool deck at a location where the game will
be played in shallow water depths. Figure 6 shows the layout for positioning the anchor sockets.
Bond anchors as required.
2) Install the eyebolts into the basketball frame and the volleyball post assembly as shown in
Figure 7.
D1 D2 D3
12 in. Min 12 in. Min 20 ft. 10 in. Max
ITEM # PART # DESCRIPTION QTY.
1 5-332 3/8-16 x 3 7/8 Stainless Steel Eyebolt 4 ea.
2 5-141 3/8-16 Lock Nut 4 ea.
3 05-608 Nut Cap-Black Rubber 4 ea.
4 20-109 Volleyball Post Assembly 1 ea.
FIGURE 6
FIGURE 7

6
3) Insert the assembled volleyball post and basketball frame into the anchor sockets. To switch
between using the volleyball game and the basketball game you must rotate the basketball frame
180 degrees. For volleyball, the eyebolts on the back of the basketball frame need to be facing
the pool; this position is shown in Figure 6. The procedure for rotating the basketball frame is: 1)
Loosen the setscrews in the expandable collar 2) Rotate the frame to the desired position 3)
Retighten the setscrew in the expandable collar.
4) The volleyball net attaches to the eyebolts in the volleyball post and the basketball frame. When
the volleyball net is in use, be sure that any loose rope from the volleyball net is properly secured
so as to not provide a hazard.
5) Be sure that caps are placed in the anchors when the volleyball post or the basketball frame is
removed.