SAB xFinder 2 User manual

1
CONTENTS
1.SAFETY ............................................................................................................................................................ 3
2.INTRODUCTION............................................................................................................................................ 3
3.FEATURES....................................................................................................................................................... 4
4.REMOTE CONTROL ..................................................................................................................................... 5
5.FRONT PANEL ............................................................................................................................................... 6
6.REAR PANEL .................................................................................................................................................. 8
7.CONNECTING YOUR SYSTEM .................................................................................................................. 8
8.BASIC OPERATIONS .................................................................................................................................. 11
8.1TURN ON XFINDER......................................................................................................................................... 11
8.2POWER........................................................................................................................................................... 11
8.3CHANNEL UP/CHANNEL DOWN ..................................................................................................................... 11
8.4VOLUME UP/VOLUME DOWN ........................................................................................................................ 11
8.5NUMBER ........................................................................................................................................................ 11
8.6MUTE ............................................................................................................................................................ 11
8.7PAUSE............................................................................................................................................................ 11
8.8AUDIO ........................................................................................................................................................... 11
8.9INFORMATION................................................................................................................................................ 12
8.10EPG ........................................................................................................................................................... 12
8.11TV/RADIO................................................................................................................................................ 13
8.12CHANNEL LIST ........................................................................................................................................... 13
8.13PAGE UP/PAGE DOWN ............................................................................................................................... 14
8.14TXT........................................................................................................................................................... 14
8.15SUBTITLE ................................................................................................................................................... 14
8.16ZOOM......................................................................................................................................................... 14
8.17MENU......................................................................................................................................................... 14
8.18VIDEO FORMAT.......................................................................................................................................... 14
8.19EXIT ........................................................................................................................................................... 15
9.FINDER........................................................................................................................................................... 15
9.1SATELLITE INSTALLATION ............................................................................................................................. 15
9.2AUTO INSTALLATION..................................................................................................................................... 18
9.3TERRESTRIAL INSTALLATION ........................................................................................................................ 18
9.4CABLE INSTALLATION ................................................................................................................................... 18
10.ANGLE(SATELLITE GUIDE) .................................................................................................................... 19
11.CONSTELLATION ....................................................................................................................................... 20
12.SPECTRUM ................................................................................................................................................... 20
13.SERVICE ........................................................................................................................................................ 22
13.1ORGANIZING SERVICE................................................................................................................................ 23
13.2ORGANIZING FAVOURITES ......................................................................................................................... 24
13.3EPG ........................................................................................................................................................... 25
13.4CA SETTING............................................................................................................................................... 26
14.MEDIA ............................................................................................................................................................ 27
14.1FILE LIST ................................................................................................................................................... 27
13.1.1 Record Files .............................................................................................................................................. 27
13.1.2 MP3 Files.................................................................................................................................................. 27
13.1.3 Image Files................................................................................................................................................ 28
13.1.5.Software .................................................................................................................................................... 30
13.1.4All............................................................................................................................................................... 30
14.2STORAGE INFORMATION ............................................................................................................................ 30
14.3PVR SETTING ............................................................................................................................................ 31
14.4USB SPEED TEST ....................................................................................................................................... 31
14.5REMOVE USB DEVICE SAFELY! ................................................................................................................. 31
15.SYSTEM ......................................................................................................................................................... 31

2
15.1INFORMATION ............................................................................................................................................ 31
15.2BATTERY INFORMATION ............................................................................................................................ 32
15.3DEFAULT SETTING ..................................................................................................................................... 32
15.3.1Default Value:........................................................................................................................................ 32
15.3.2Delete All Channel: ............................................................................................................................... 32
15.3.3Save default value.................................................................................................................................. 33
15.4SOFTWARE UPGRADE................................................................................................................................. 33
15.4.1 Upgrade by RS232:................................................................................................................................... 33
15.4.2 Upgrade By USB.................................................................................................................................... 33
15.4.3 Backup to USB ....................................................................................................................................... 33
15.4.4 Http Upgrade ............................................................................................................................................ 34
15.4.5 FTP Upgrade ............................................................................................................................................ 34
15.4.6 Upgrade By Satellite ................................................................................................................................. 34
15.4.7 Upgrade By Terrestrial............................................................................................................................. 34
15.4.8 Upgrade By Cable..................................................................................................................................... 34
15.5LANGUAGE ................................................................................................................................................ 34
15.6A/V CONTROL ........................................................................................................................................... 35
15.7ETHERNET SETTING ................................................................................................................................... 36
15.8TIME SETTING ............................................................................................................................................ 36
15.9TIMER ........................................................................................................................................................ 37
16.NEW FEATURES .......................................................................................................................................... 38
16.1TIME SHIFT ................................................................................................................................................ 38
16.2RECORD ..................................................................................................................................................... 38
17.APPLICATION.............................................................................................................................................. 39
17.1 YOUTUBE ......................................................................................................................................................... 39
17.2 RSS READER .................................................................................................................................................... 39
17.3 WEATHER FORECAST ....................................................................................................................................... 39
17.4 GOOGLE MAPS ................................................................................................................................................. 40
17.5 FTP .................................................................................................................................................................. 40
17TROUBLE SHOOTING................................................................................................................................ 41
18SPECIFICATIONS ........................................................................................................................................ 42

3
1. SAFETY
This HD Xfinder has been manufactured to satisfy the international safety standards.
Please read the following safety precautions carefully.
MAINS SUPPLY: 100 - 240V AC 50/60Hz
OVERLOADING: Do not overload wall outlet, extension cord or adapter as this may result in fire or
electric shock.
LIQUIDS: Keep liquids away from the HD Xfinder. The apparatus shall not be exposed to dripping or
splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.
CLEANING: Disconnect the HD Xfinder from the wall outlet before cleaning .Use a light damp cloth
(no solvents) to dust the HD Xfinder.
VENTILATION: The slots on top of the HD Xfinder must be left uncovered to allow proper airflow to
the unit. Do not stand the HD Xfinder on soft furnishings or carpets. Do not expose the HD Xfinder to
direct sunlight or do not place it near a heater. Do not stack electronic equipments on top of the HD
Xfinder.
ATTACHMENTS: Do not use any attachments that are not recommended as these may cause
hazard or damage the HD Xfinder.
CONNECTION TO THE SATELLITE DISH LNB: Disconnect the HD Xfinder from the mains before
connecting or disconnecting the cable from the satellite dish.
FAILURE TO DO SO CAN DAMAGE THE LNB.
CONNECTION TO THE TV: Disconnect the HD Xfinder from the mains before connecting or
disconnecting the cable from the satellite dish.
FAILURE TO DO SO CAN DAMAGE THE TV.
EARTHING: The LNB cable MUST BE EARTHED to the system earth for the satellite dish.
LOCATION: Place the HD Xfinder indoor in order not to expose to lightening, rain or sunlight.
2. INTRODUCTION
Thank you for purchasing the HD Xfinder.
This HD Xfinder can fast spectrum analysis with 950 ~ 2150 MHz frequency span. Support
Constellation Chart. it has a High resolution 7"TFT LCD and a lithium battery can work at outdoors. It
has a 2GB of U disk , so you needless schlep hard disk when it work at outdoors. And also use as a
DVB-S+T/C Xfinder on a TV.
This HD Xfinder is fully compliant with the international DVB standard and thus transmits digital
images, sounds, information guides and teletext directly to your TV or Xfinder through the satellite
broadcasting.
Now you can comfortably see and receive digitally transmitted music, news, movie and sports satellite
broadcasts in your office or at your home.
In service search section, both the automatic service search method and the manual search mode
are provided. Also it supports DiSEqC 1.0, 1.2 and USALS, enabling you to move your antenna in
order to focus preferred satellite. You can save up to 6000 TV and Radio services and work around
with the favorite, Lock, Delete, Move and Sort functions.
The menu is very modern and supports multiple languages. All functions can be carried out using the
remote control and some of the functions can also be carried out using the front panel. The HD

4
Xfinder is easy to use and adaptable for future advances. Please be aware that new software may
change the functions of the HD Xfinder.
If you have any difficulties concerning the operation of your HD Xfinder, please refer to the relevant
section of this manual, including the ‘Troubleshooting’. This Manual will provide you with useful
information on using the HD Xfinder.
3. FEATURES
zMPEG-Fully DVB-S / DVB-S2 HD compliant
zDVB-T/DVB-T2/DVB-C
zFast spectrum analysis
zSupport Spectrum information save, load and compare.
zData parsing of frequency Selected
zConstellation Chart
zHigh resolution 7"TFT LCD
zLarge lithium battery capacity (5500mAh)
zAuto Calculate Angle of AZ ,EL
z6000 channels (TV and Radio) programmable
zMultilingual menu text support
zChannel switching time less than 1 second
zChannel list editing
zFavorite channel list editing
zTrue-color On-Screen Display (OSD)
zFull Picture In Graphic (PIG) function
zElectronic Program Guide (EPG) for on screen channel information
zSubtitle supported
zTeletext supported by VBI insertion and software emulation
zProgram and Channel information transfer from Xfinder to Xfinder
zDiSEqC 1.0, 1.1, 1.2 and USALS
zHDMI HD Video/Audio Output
zEasy upgrading by Ethernet & USB &RS 232 Port
zUSB 2.0 Host
zBuilt in U disk (4GB)
zLAN 10/100Mbps Ethernet
zRTC (Real-Time-Clock)
zTime Shift
zVideo Recording
zRecording one channel and Time Shifting another channel
zOne key to start or stop recording of TS stream

5
4. Remote Control
You can power on/off the Xfinder, operate on screen
menu, and use a variety of hot key function.
POWER
To switch the Xfinder power on/off
MUTE
Used to enable or disable the audio
NUMERIC KEYS
Used to select channels or enter programming parameters
TV / RADIO
Xfinder switches between TV and Radio mode.
0 (ZOOM)
Press 0 key select zoom times, from X1 to X16.
AUDIO
Audio channels setup, to select audio mode; Left, Right , Stereo,
Mono.
F1
To switch LCD on/off
F2
To switch fan on/off
F3
To start or stop recording of TS stream
F4
To display channel status or various program information of
current service.
F5
To switch AV output/input
EPG
Display the Programs guide on screen when available.
MENU
Displays the Main Menu on the screen, or return to the previous
menu or status.
EXIT
Cancel the user selection and return to the viewing mode from a
menu.
OK
To select menu option, or to updated on entry.
<,> KEY
To adjust volume level, or to move cursor left or right in the
menu.
^,v KEY
To change channels, or to move cursor up or down in the menu.
PAGE+/PAGE-
To move up the cursor to the next or previous page
in the menu or channel list.
●REC
To start the recording.
Red Key
Has different functions per menu.
TXT(YELLOW KEY)
Shows teletext information of the current channel supports.
Subtitle(Green KEY)
Subtitle Display.
V.FORMAT (blue Key)
Press V.FORMAT button to switch the display mode among
"Auto","ByNativeTV"720p_50","720p_60"”,”1080i_50”,”1080i_60",
”1080p_50” and "1080p_60".
Play
To play the MP3, JPEG, or Record files.

6
Stop
To stop the Time Shift, recording, or MP3/JPEG player.
PAUSE
Used to select the freeze function.
Press once to freeze the screen picture.
FB
To start Fast Backward function.
FF
To start Fast Forward function.
5. Front panel
POWER
To switch the Xfinder power on/off
NUMERIC KEYS
Used to select channels or enter programming parameters
０ (ZOOM)
Press ０key select zoom times, from X1 to X16.
FIND
shortcut key enter to Xfinder menu.
ANGLE
shortcut key enter to Angle menu.
SPCM
shortcut key enter to Spectrum menu.
SERVICE
shortcut key enter to Serice.
MEDIA
shortcut key enter to Media menu.
SYSTEM
shortcut key enter to System menu.
F1
To switch LCD display on/off
F2
To switch fan on/off

7
F3
To start or stop recording of TS stream
F4
To display channel status or various program information of current service.
F5
To switch AV output on/off
MENU
Displays the Main Menu on the screen, or return to the previous menu or status.
EXIT
Cancel the user selection and return to the viewing mode from a menu.
OK
To select menu option, or to updated on entry.
V-,V+ KEY
To adjust volume level, or to move cursor left or right in the menu.
CH+,CH-KEY
To change channels, or to move cursor up or down in the menu.
PAGE+/PAGE-
To move up the cursor to the next or previous page
in the menu or channel list.
AUDIO(Red)
Audio channels setup, to select audio mode; Left, Right , Stereo, Mono.
Red Key
Has different functions per menu.
TXT(YELLOW KEY)
Shows teletext or subtitle information of the current channel supports.
Subtitle(Green KEY)
Subtitle Display.
V.FORMAT (blue Key)
Press V.FORMAT button to switch the display mode among
"Auto","ByNativeTV"720p_50","720p_60"”,”1080i_50”,”1080i_60",”1080p_50” and "1080p_60".
FUN
To select brirhtness,contrast and colour of LCD screen.
<,> KEY
To adjust brirhtness,contrast and colour of LCD screen.

8
6. Rear Panel
Please refer to the diagram above for all possible connections of your Xfinder
Do not connect the unit to the mains socket until all other connections have been made and checked.
Your configuration can vary depending on model
DC 12V: Connect the external power supply（DC 14.5V/4A）.
RF OUT: This enables the connection of another Xfinder.
RF IN: This port is to connect the coaxial cable from terrestrial antenna/cable antenna
LOOP: This enables the connection of another Xfinder.
LNB IN 13/18V 300mA MAX: This port is to connect the coaxial cable from LNB of your Dish.
HDMI: Audio and Video output socket for TV set with HDMI Input Jack only.
RS 232: SERIAL PORT: This is used to connect your Xfinder to a computer through a serial cable
Ethernet: Network port, you can get a new software updates from this port.
USB: USB 2.0 Host, connect to USB hard disk, or flash disk.
CA: One slot CA Interface for Conax.
7. Connecting Your System
This section describes how to connect your product to match your particular devices setup and to gain
optimum signal quality. The product provides various interfaces to connect to the TV, VCR or other
devices. Select the most appropriate depending on the device you have.
Warning: Connect all components before plugging any power cords into the wall outlet.
Always turn off the product, TV and other components before you connect or disconnect any cables.

9
Note: If you encounter any problems setting up your product, please contact your local retailer
helpline.
7.1 Connecting the Antenna
1. Connect one or two satellite coaxial cable from the wall to LNB IN.
2. Connect a cable/terrestrial coaxial cable to AERIAL IN.
Note: Cable and terrestrial can't concurrence.
Connecting the TV
1. TV with the HDMI connector:
For the best picture quality, connect the product and TV using an HDMI cable.
·
Note:
1. Connecting your TV directly to the audio/video output of the product will assure a more vivid
picture and enhance your viewing enjoyment.
Connecting to the LAN:
Connect one end of the Ethernet cable to the product and the other end to the LAN router.
TV with Motorized System (DiSEqC 1.2)
Connect one end of your coaxial cable to the LNB IN connector on the Xfinder and the other end to
the REC or Xfinder connector on the DiSEqC 1.2 motor.
Connect the coaxial cable from the LNB to the LNB connector on the DiSEqC 1.2 motor.
All our Xfinders are designed to be DiSEqC 1.0 and DiSEqC 1.2 compatible.
This allows multiple antennas to be connected to the Xfinder at the same time.

10
If you have two or more fixed antennas or LNBs, then we recommend you use a DiSEqC 1.0
switch.
Connect the coaxial cable from the first LNB to the LNB 1 or LNB A input connector of the DiSEqC
switch.
Do the same for any other LNBs that you have.
Connect one end of a coaxial cable to the RF output connector of the DiSEqC switch,
connect the other end to the LNB IN socket on the Xfinder.
To the digital Xfinder, you can connect either a single satellite antenna directly or LNB of
multi-feed equipment.

11
8. Basic Operations
8.1 Turn on Xfinder
First, press the Device’s Main [Power] button to
turn on the unit. When the Xfinder is first used,
there will play the first channel from the default
Channel List. If the Xfinder is not first used,
Xfinder will play the same channel as last time
before turning off.
?Frequently Asked Question
Q: The power of my Xfinder has been turned
on and not in Standby mode, but the TV
screen showed nothing:
A: Make sure the TV set has been set to the
correct video input (not the TV channels). For
example, if you have connected the unit with the
Video1 input of the TV set, the TV set has to be
switched to Video1.
Q: The power of my Xfinder has been turn on
and not in Standby mode, but the TV
screen showed nothing except one box
with “No Signal” image.
A: That means the channel, which you select, is
no signal. It could be several causes:
1 The channel which you select is not in your
allocate satellite. The simply solution is to
change channel.
2 The signal of current TV channel is too
weak. You can try to change channel to
other strong signal channels. If the
problems still exist, please consult your
local dealer or other professionals for
technical service.
3 You use the Dual LNB, and you need
Modify LNB Type
8.2 Power
1 Press [Power] Key can enter the Standby
state
2 In Standby state, press [Power] Key again
can call back the unit and go on play the
previous channel
3 User can also disconnect the device’s main
power to end the Standby state.
8.3 Channel Up/Channel Down
In full screen, press [CH+/CH-] to change
channel.
8.4 Volume Up/Volume Down
In full screen, press [VOL+/VOL-] to adjust
volume.
8.5 Number
In full screen, use number key and press [OK]
on the Remote Control Unit to change channel.
8.6 Mute
1 Press [MUTE] key to mute the sound and
the screen will show up mute OSD.
2 Press [MUTE] key again to restore sound.
8.7 Pause
1 In playing mode, press [Pause] key, the
picture will be paused, but the sound of the
channel will still continues.
2 Press [Pause] key again, the screen’s
picture will skip over to the current playing
picture, and the sound of the channel will
correspond playing.
.
8.8 Audio
1 In full screen, press [AUDIO] key can open
the “Audio” window on the screen.

12
2 You can modify the audio track by press
[CH+/CH-] key and modify the audio
mode by press[VOL+/VOL-] key.
3 Mode: Left/Right/Stereo/Mono
8.9 Information
In full screen, press [F4] key can open
information screen, in the window shows the
parameters of current channel.
8.10 EPG
1 The Xfinder has an Electronic Program
Guide (EPG) to help you navigate channels
through all the possible viewing options.
The EPG supplies information such as
channel listings and starting and ending
times for all available channels.
Press [EPG] key to display EPG screen.
2 Press [Red] key can select the channels by
different group, such as by Favorite
/Satellite /Provider /CAS etc.
3 Press [Green] key to select different display
mode among Now EPG, Next EPG, More
and Schedule, like the following picture:
4 Press [Yellow] key in EPG menu can set
one record timer or go to Timer List menu.
5 In EPG menu, when you select one event
by high light item, you can set this event to
record timer list directly by press [REC]
button.

13
6 In EPG menu, press [Exit] to close EPG
screen.
8.11 TV/RADIO
In TV mode, pressing [TV/RADIO] key can
switch to Radio mode. In Radio mode, press
[TV/RADIO] key to switch to TV mode.
8.12 Channel List
1 In full screen, press [OK] key can enter
“Channel List”.
2 Press [CH+/CH-] key to change the
different group. Which you can watch like
below
3 Press [Red] key to display details
information for EPG Now.
4 Press [Green] key you can change the
current channel’s property, such as FAV/ Lock/
Skip/ Delete/
Rename
5 Press [Yellow] key can open the “Find”
window like below. You can press
[Up/Down/left/right] keys to move highlight
and press [OK] key to input the letter.
Select OK and press [ok] button to find you
want.
6 Press [Blue] key can open the “Sort”
windows like below. There are five kinds of
sorting ways. You can press [Ch+/Ch-] key
to move highlight and press [OK] key to
confirm you
selection.

14
The five kinds of sorting way are:
Default: Sorting by scanning result.
FTA/$: Sort channel through free and
scramble sequence. Free channel will
in the front of channel list and scramble
channel will at the rear of channel list
Lock: Accumulated all locked channels
and list in the last of TV Channel List.
Name (A-Z): Sorting in Alphabetical
Order, ignore “$” symbol.
Name (Z-A): Sorting in Alphabetical
Order, ignore “$” Symbol.
7 Press [CH+/CH-] key to move highlight and
press [OK] key to play the highlighted
channel.
8 Press [Page Up/Down] key to page up and
page down.
9 Press [Exit] key to exit the channel list.
8.13 Page Up/Page Down
In Channel list, press [Page+/Page-] key can
page up and page down the channel list.
8.14 TXT
1 Press [Yellow] key in full screen, you can
open teletext page on the channel which
has teletext information.
2 If the channel has no teletext information,
it will show “No Teletext Data” on the
screen.
8.15 Subtitle
1 Press [Green] key in full screen, you can
open subtitle page on the channel which
has subtitle information.
2 If the channel has no subtitle information,
it will show “No subtitle Data” on the
screen.
8.16 Zoom
1 The [0] key allows you to magnify a certain
area on the images
2 Press [0] key again, the image will enlarge
rotate as x1, x2, x4, x6, x8, x12, x16.
3 In “x2 ~ x16” image, using [Up/
Down/Left/Right] keys to move the
image center area you want to see.
4 In zoom mode, press [Exit] to close “Zoom”
window.
8.17 Menu
Press [MENU] key can open the menu,
exit the current menu to last menu or close
the window.
8.18 Video Format
1 Press [v.Format] (blue) key under Full
Screen playback for 1st, it will show the
current system outputting video resolution,
continuously press this key, system will
switch its outputting video resolution by
sequence “Auto-> By Native TV ->
720P_50> 720P_60-> 1080i_50->
1080i_60-> 1080p_50->1080p_60”.

15
8.19 Exit
1 Press [EXIT] key can exit the current menu
to last menu or close the window.
9. Finder
1 Press [OK] key to select finder
2 Press[CH+/CH-] key to select one item.
3 Press [menu] key to back to main menu.
9.1 Satellite Installation
Satellite list
1 You can move highlight by press [CH+/CH-]
key or Press [P+/P-] key to page up or page
down and [OK] key to select the Satellite.
2 Press [left] or [green] button to enter TP List.
Note: You can't edit and scan the TP when you press
[left] button, it only show the list.
3 Press [right] button to enter into DiSEqC
Setting menu.
Auto DiSEqC: Press [ok] key to run Auto
DiSEqC function, it can find the satellite
connect to which port automatically.
DiSEqC1.0: Press [VOL+/VOL-] button to
select one item among Disable, 1/2, 2/2, 1/4,
2/4, 3/4, 4/4.
DiSEqC1.1: Press [VOL+/VOL-] button to
select one item among Disable, 1/8, 2/8, 3/8,
4/8, 5/8, 6/8, 7/8, 8/8, 1/16, 2/16, 3/16, 4/16,
5/16, 6/16, 7/16, 8/16, 9/16, 10/16, 11/16,
12/16, 13/16, 14/16, 15/16, 16/16.
Motor: Press [VOL+/VOL-] button to select one
item among Off, DiSEqC1.2, USALS.
4 Press [ ] button to switch between Beep
on and Beep off.

16
5 Press [red] button to display the scan menu,
and then setting parameter, at last select
Manual Scan or Blind Scan to scan channels
of the selected satellites or TP. If you select
Blind Scan, NIT Search needless edit.
Note: Manual Scan can only scan channels of the
TP that in the TP list, but Blind Scan can scan
channels needless TP, it can search the has signal
TP.
Scan Mode: Press [VOL+/VOL-] button to
switch it between All and Free (means you
want to scan all channels or only scan free
channels).
Program Type: Press [VOL+/VOL-] button to
switch it among TV + Radio, TV Channel,
Radio (means you want to scan all channels,
all radio or only scan TV/Radio channels).
NIT Search: Press [VOL+/VOL-] button to
switch it between On and Off. If selected On,
meaning receive the latest transponder
information.
6 Press [yellow] button to switch to antenna
parameter list of highlight satellite.
LNB Type: Press [ok] button and then press
[VOL+/VOL-] button to select one item
among Universal, standard, user, unicable.
For Example: If you use the unicable LNB,
then you should select “Unicable” option in
“LNB Type” and will display the submenu for
Unicable setting.
TP Index: Press [VOL+/VOL-] button, or
press [ok] button and then press [CH+/CH-]
button to switch TP.
22K: Press [VOL+/VOL-] button, or press [ok]
button and then press [CH+/CH-] button to
select on or off. When this item is switched to
“ON”, Xfinder will receive TV and radio input
signal from 22K port. If the item is switched to
“Off”, the Xfinder will receive all signals from
0K port.
Note: When LNB Type is universal, 22K can’t edit.
DiSEqC1.0: Press [VOL+/VOL-] button to
select one item among Disable, 1/2, 2/2, 1/4,
2/4, 3/4, 4/4.
DiSEqC1.1: Press [VOL+/VOL-] button to
select one item among Disable, 1/8, 2/8, 3/8,
4/8, 5/8, 6/8, 7/8, 8/8, 1/16, 2/16, 3/16, 4/16,
5/16, 6/16, 7/16, 8/16, 9/16, 10/16, 11/16,
12/16, 13/16, 14/16, 15/16, 16/16.
LNB Power: Press [VOL+/VOL-] button, or
press [ok] button and then press [CH+/CH-]
button to switch it among 13V/18V,
13.5V/18.5V, off.
7 Press [blue] button to enter into edit menu.
When in the satellite list it enter edit satellite
menu, or it enter edit TP menu.
8 Press [white] button enter into SI Info menu.
It shows the information of current TP. Like
frequency, provider name, network name,
network ID, Stream ID, Network TP Count,
TV list, radio list, level, quality, RF Level,
FEC, C/N, BER, MER. Press [red] button to
display the Network TP List.
Edit Satellite

17
Press [CH+/CH-] key to select one item among
Add Satellite, Edit Satellite, and Delete
Satellite.
1. In "Add Satellite" item, press [ok] key to add
a new Satellite.
Name: Press [ok] button to enter into key
board menu to input the name. Press
[V-/V+]button to select the letter and press
[ok] button to input it, when finish select “ok”
and press [ok] button.
Longitude: Press number keys to input the
longitude, and press [VOL+/VOL-] button to
select east or west.
2. In "Edit Satellite" item, press[ok] key to edit
the selected Satellite
Note: If you selected more than one satellite, it will
edit the highlight satellite.
Name: Press [ok] button to enter into key
board menu to input a new name. Press
[VOL+/VOL-] button select the letter and
press [ok] button to input it, when finish
select “ok” and press [ok] button.
Longitude: Press number keys to input the
longitude, and press [VOL+/VOL-] button to
select east or west.
3. In "Delete Satellite" item, press[ok] key and
select “yes” to press [ok] button to delete
the selected Satellite.
Note: If you selected more than one satellite, it will
delete the highlight satellite.
TP list
Press[CH+/CH-] key to select one item among
Add TP, Edit TP, Delete TP and Delete All TP.
1. In "Add TP" item, press [ok] key to add a
new TP.
Frequency: Press [VOL+/VOL-] button or
press number keys to set the frequency.
Symbol Rate: Press [VOL+/VOL-] button
or press number keys to set the rate.
Polarity: Press [VOL+/VOL-] button to
select Horizontal or vertical.
Note: The parameters of “Frequency” and
“Symbol Rate” can set by number keys. The
available range are “3000~13450 MHz” and
“1000~45000Ks/s”.
2. In "Edit TP" item, press[ok] key to edit the
selected TP
Note: If you selected more than one TP, it will edit
the highlight TP.
Frequency: Press [VOL+/VOL-] button or
press number keys to set a new frequency.
Symbol Rate: Press [VOL+/VOL-] button
or press number keys to set a new symbol
rate.
Polarity: Press [VOL+/VOL-] button to
select Horizontal or vertical.
Note: The parameters of “Frequency” and
“Symbol Rate” can set by number keys. The
available range are “3000~13450 MHz” and
“1000~45000Ks/s”.
3. In "Delete TP" item, press[ok] key and
select “yes” to press [ok] button to delete
the selected TP.

18
Note: If you selected more than one TP, it will
delete the highlight TP.
4. In "Delete All TP" item, press[ok] key and
select “yes” to press [ok] button to delete All
TP.
9.2 Auto Installation
“Auto Installation” is a very new and convenient function.
It will automatically detect all dishes connecting to this
machine and scan the available services belonging to
the satellite matched according to satellites and
transponders data in current database. You don’t have
to input any parameter of your antenna settings. Just
press “ OK ” button to enter this “Auto Installation” menu
then it starts scanning and shows you the result at the
end of scanning.
9.3 Terrestrial Installation
Press [OK] key to enter the selected item.
1. You can select the Bandwidth according
different country.
2. You can set the Tuner Power ON/OFF.
3. Press [Red] key can directly into blind scan
mode to scan the current programs.
4. Press [Green] key to enter the following
menu.
Scan Mode.
1 There are two modes. You can scan channel
by
channel or by frequency”.
2 When scan band is UHF and region is
“France”,the range of Ch No. is from 21 to 69.
When scan band is VHF and region is
“France”, the range of Ch No. is from 1 to 9.
(it’s according to region)
3 Press [Red] key to enter blind scan menu, or
press [Green] key to enter TP scan menu.
4 Press [Exit] key to exit the scanning.
9.4 Cable Installation
Press [OK] key to enter the selected item.
1. You can input the Frequency by use the
numeric button of the RCU.
You can select the QAM value among
16QAM, 32QAM, 64QAM, 128QAM and
256QAM.
You can turn ON or OFF the NIT Search, if
you set the Scan Mode to Manual Scan.
2. Press [green] button to add a new TP.
3. Press [Yellow] button to delete the select
TP
4. Press [blue] button to delete the all TP.
5. Press [white] key to enter blind scan
menu, or press [Red] key to enter TP scan
menu.

19
6. Press [Exit] key to exit the scanning.
10. Angle(Satellite Guide)
When you enter to “Angle” menu, you will see
the screen like below:
“Angle” is use for user to enter local longitude;
local latitude and satellite longitude. By the
evaluation from the Xfinder evaluate the
antenna azimuth and antenna elevation; user
can follow this guidance to adjust antenna.
1 In “Satellite” item, press [VOL+/VOL-] key to
switch satellite that you want to set or press
[OK] key to enter satellite list for selection.
2.In “Satellite Longitude” Item, display
Longitude value of current Satellite. You can
edit it by number keys and [VOL+/VOL-] key.
3.In “Local” Item, press [VOL+/VOL-] key to
select Manual or city that satellite setting
Press[Red] key to add a new city
Press [Green] key to edit the select city.
When you press [Yellow] key, there will
show up a warning message for reminding
whether you will delete the current city or
not. If you select “Yes”, the current city will
be deleted.
When you press [blue] key, there will show
up a warning message for reminding
whether will delete all cities or not. If you
select “OK”, all cities will be deleted.
4. You can use number keys to input
parameters in “Longitude” and “Latitude” at add
city and edit city menu.
5. You can use [VOL+/VOL-]key to select
east or west in “Longitude” and “Satellite
Longitude”, select north and south in
“Latitude”.
6. Moving highlight to “calculate” item and
press [OK] key. The lower column on the
screen will calculate the corresponding value
automatically.
7. Orientation means the angle between south
and satellite.

20
Press [MENU] key to draw back to “Main”
Menu.
11. Constellation
When you enter to “Constellation” menu, you will
see the screen like below: It show the picture of
constellation.
DVB-S Constellation
DVB-S2 Constellation
Note:If current TP has not signal, it will show
ruleless white dot. And the stronger the signal,
the higher the concentration of white spots
22 k
You can use [red] key to switch “on/ off”. When
this item is switched to “ON”, Xfinder will receive
TV and radio input signal from 22K port. If the
item is switched to “Off”, the Xfinder will receive
all signals from 0K port.
DisEqc Setting
Press [green] key enter “DisEqc Setting” Menu,
you will see the screen like below:
1.DiSEqC1.0: You can use[Volume Up/ Volume
Down]key to switch options. There are several
options for your selection:
a) Disable: without DiSEqC.
b) 1/2, 2/2: two ports DiSEqC
c)1/4, 2/4, 3/4, 4/4: 4 ports DiSEqC
2.DiSEqC1.0: You can use[Volume Up/ Volume
Down]key to switch options. There are several
options for your selection:
a) Disable: without DiSEqC.
b)1/8, 2/8… 8/8: 8 ports DiSEqC
c)1/16, 2/16….16/16: 16 ports DiSEqC
Frequency
You can input number keys to the Frequency,
The available range are “3000~13450 MHz”
Symbol Rate
You can input number keys to set the Symbol
Rate, the available range are
“1000~45000Ks/s”
Polarity
In “Polarity” item, press [Left/ Right] key to select
Horizontal or Vertical”.
Start
Press [ok] key to start to draw the Constellation.
12. Spectrum
When you enter to “Spectrum” menu, you will
see the screen like below: