SAFESTOR Skipton SFSM001 User manual

Skipton Bike Locker
SELF ASSEMBLY INSTRUCTIONS
SFSm001
www.spearheadbikes.co.uk

www.spearheadbikes.co.uk
KPF0675
SFSM001_E
KPF0680
KPF0684
KPF0682
SFSM001_D
KPF0681
SFSM001_F
KPF0676
No. Qty Code Descripon
BASE PANEL
REAR LH SIDE PANEL
REAR RH SIDE PANEL
BACK FASCIA PANEL
BACK PANEL
FRONT LH SIDE PANEL
FRONT RH SIDE PANEL
FRONT FASCIA PANEL
ROOF PANEL
1
2
3
4
5
6
7
8
9
x 1
x 1
x 1
x 1
x 1
x 1
x 1
x 1
x 1
SFSM001_A
KPF0687
KPF0688
SFSM001_001
KPF0338
NBW4013
NBW7000
KPF0397
DOOR ASSEMBLY
RAMP
SOCKET ATTACHMENT
FLOORING
ROOF BRACKETS
SELF TAPPER SCREWS
COUNTER SUNK SCREWS
PACKING PIECES
10
11
12
13
14
15
16
17
x 1
X1
x 1
x 2
x 20
x 122
x 12
x 10
No. Qty Code Descripon
SELF ASSEMBLY INSTRUCTIONS
Before Assembly
It is important you have a level rm
base for your unit. This should be
constructed from concrete, tarmac
or ags and be a minimum of 50mm
(1.9”) deep.
Stor Measurement
1012mm x 2055mm
(40” x 81”)
Minimum base measurement
1250mm x 2300mm
(49” x 91”)
Recommended:
Powerdriver
Silicone Sealant
Door Alignment and Placement
If you need the door to open on the reverse side this can be achieved by switching the back
panel with the door panel, this will result in the door handle being upside down.
Once assembly is completed following the guide provided, it is necessary to correctly level
the unit using the packing pieces supplied.
Slide the packing pieces under the corners of the units base as required unl an equal gap
has been achieved around the doors allowing smooth operaon.
Sealant
If required joints can be sealed with sealant. Apply a bead of sealant along the panels at each
stage. Wipe away any excess sealant immediately with a damp cloth.
YOU WILL NEED
USI 026 21-04-2016
RECORD YOUR
KEY NUMBER HERE:
Please note: Part 12 the Electric Socket aachment can be ed on the LH side of the unit by removing two screws from the side
panels. It is compable with BSS733 single paresses 60.2mm and twin paresses 120.6mm. This allows for charging inside the unit.
When building your unit on a holiday park please check regulaons on electricity to outdoor units rst.
9
4
5
12
1
3
13
7
10
11
8
6
2
15
16
17
14

step by step
www.spearheadbikes.co.uk
7
1
3
2
4
step 1 step 2
step 3 step 4
Posion Front RH (right hand) side panel 7 into the groove on the Base
panel 1 ensuring the holes are aligned.
One person should hold the panels, whilst, the other screws the panels
together using Self Tapper screws 15 . All screws should go in from the
inside of the unit.
Posion Rear RH (right hand) side panel 3 into the groove on the base panel
1 and the already xed Front RH (right hand) side panel 7 , ensure the
holes are aligned and screw together.
Posion Rear LH (le Hand) side panel 2 into the groove on base panel 1
and opposite the already xed Rear RH side panel 3 . Ensure the holes are
aligned and screw together.
Posion Back Fascia panel 4 between the two Rear side panels 2 and 3
at the top of the unit. Ensure the holes are aligned and loosely screw together,
creang a gap for the back panel.
SELF ASSEMBLY INSTRUCTIONS
X 18
15
X 7
15
X 7
15
X 4
15
Mobility Scooter Stor

step by step
www.spearheadbikes.co.uk
step 5 step 6
step 7 step 8
Posion Back panel 5 into the groove on the base panel 1 , between the
side panels 2 and 3 , and under the Back Fascia panel 4 . Ensure the
holes along all four sides are aligned and screw together, ghten the screws
for the Back Fascia panel.
Posion Front LH side panel 6 into the groove on the base panel 1 and
Rear LH side panel 2 . Ensure the holes are aligned and screw together down
the full length of the vercal joint and across the base.
Li the Roof panel 9 onto the unit, covering the other panels and fascia pan-
els. Screw into place using the single screw holes. Fit the Roof security brackets
14 in the pair of slots on the top of each of the panels, each bracket is ed
with a single screw.
5
6
8
9
14
Aach the Fascia panel 8 across the front of the unit as pictured. Screw
into both the Front side panels 6 and 7 .
SELF ASSEMBLY INSTRUCTIONS
X 18
15
X 18
15
X 4
15
X 44
15
9
14

step by step
www.spearheadbikes.co.uk
10
step 9
Support the door at all mes whilst ng the counter sunk screws 16 to ensure correct alignment, always use a hand held screwdriver.
Posion the Door 10 so that the hinges are aligned with the xing holes, screw together.
SELF ASSEMBLY INSTRUCTIONS
X 12
16
13
step 11
Finally slot the Wooden ooring 13 into place ensuring that the cut out is
at the front near the locking mechanism.
11
step 10
Align the Ramp 11 with the holes below the door and screw into place from
the inside of the unit using Self tapper screws 15 .
X 2
15