Sailrite 100547 User manual

TABLE STAND ASSEMBLY
Begin by unpacking all materials. Take inventory of what was
received and compare to the invoice and the Sailrite catalog.
Stand the two legs (legs come pre-assembled) upright and
facing the same direction. Align the back brace (wider bar)
with the two screw holes on the back of each leg. Thread a lock
washer and then a washer onto the screws and screw the back
brace to the leg. Place screws in both holes and then repeat
on the other leg (Figure 1). After screws are in place, secure by
tightening each screw with a socket or crescent wrench.
Table Top & Stand #100547
Assembly Instructions
• TableTopforUltrafeed
• LegTableFrameAssembly
• EuroHinge(2)
• RubberBaseforEuroHinge(2)
• DrawerwithRails
• AdjustableRubberFeet 
 Cushions(4)
• Hardware
Kit Includes:
Flip the legs upside down to attach the oor brace (narrow
bar). Align oor brace with the long slot on each leg. Take one
square nut and insert it under the slotted groove of the leg
and turn it so that its length spans the width of the leg (Figure
2). Once inserted in the leg, hold the square nut up inside the
long slotted groove with your nger and position the oor
brace over the hole in the square nut. Insert a bolt (threading
ATTACH TABLE TOP
Position the table top upside down on a soft surface that will
not damage the top. The front of the table can be identied
by the ruler on the front edge. Take the assembled leg stand
and ip it upside down also. Position the leg stand so that it
rests 1 inch from the back of the table and 3 inches from the
right edge, the edge closest to the belt opening (Figure 4 & 5).
The back brace should be along the back edge of the table,
opposite the edge with the ruler.
Thread a lock washer and then a washer onto the self-tap
screws, and attach the table stand to the table at the four
holes in the table legs. Use a drill with a socket attachment
(if available) to secure, or mark and predrill holes before
attaching the table stand.
a lock washer and washer on the bolt rst) while holding the
square nut with your nger and screw down. Repeat with
the other leg (the opposite leg may have to bend in order
to secure). Once both screws are in, position the oor brace
around the center of the legs and tighten down
(Figure 3).
Figure 1
Completed Table Top & Stand for the Ultrafeed
Figure 2 Figure 3
Figure 4 Figure 5
3”
1“
Square Nut
Back Brace
Belt Opening

2390East100South
ColumbiaCity,IN46725
800.348.2769|260.244.4647
www.sailrite.com Copyright © 2012
ADJUSTING TABLE HEIGHT
Screw down the 4 adjustable rubber feet cushions to the feet
of the stand. This will allow you to level the table. Use the nut
to secure the feet at the desirable height (Figure 7).
Use the screws on the sides of the legs to adjust the height of
the table top (Figure 8). Completely unscrew and remove the
hardware and then reattach at desired height, using one set of
the three slots in the legs.
INSTALLING DRAWER
The drawer should be attached with the table and table stand
remaining upside down. The drawer will mount on the left
underside of the table when upright. Place the drawer in the
desired location, and line up the rails beside it. Make sure that
the drawer will pull out towards the front of the table and that
it does not hang over the edge when pushed back all the way.
Secure the rails to the table with the screws provided, using a
drill to pre-drill holes (Figure 6).
PLACING SEWING MACHINE ON TABLE
If your machine is in its case, lift up the machine and loosen
the two screws (in machine casting) that lock onto the hinge
pins so the machine can be pulled o the hinges easily. You
may need assistance.
Take the hinges provided with your table top and place them
into the rubber bases for the hinges (Figure 9). The hinges
should ght tightly in the bases. Then attach the hinges
directly to the machine casting by tightening the set screws on
the hinge pins.
Once the hinges are attached to the sewing machine head,
insert the machine into the table cut out, guiding the hinges/
rubber bases into the appropriate cut out (Figure 9).
Figure 9
Figure 6
Figure 8Figure 7