Salamander EZ-LIFT Series User manual

Salamander Interactive Wall Mounts 501-517 [02.21] page 1 of 12
EZ1/ML360 user manuAl
ez-lift SERIES interactive
wall mounts
CAPACI T Y
Supports most displays up to 361.7 lbs (164.4 kg)
VESA Mounting
Horizontal - 400-600mm
Vertical - 400-1200mm
Consists of:
EZ1/MB26/396 Mount Body
EZ1/MA3 VESA Interface

Salamander Interactive Wall Mounts 501-517 [02.21] page 2 of 12
PARTS
1
x
2 x
1 x
M 6 x 1 2 m m (10x )
M 6 x 1 2 m m (10x )
o r M 8 x 1 2 m m (10x )
o r M 10 x 1 2 m m (10x )

Salamander Interactive Wall Mounts 501-517 [02.21] page 3 of 12
How to use this manual
1 Read manual carefully before you install the mount
2 Carry out the actions fully and in the given sequence
3 The mount guarantee is voided if the product is not correctly installed
 ormodiedinanyway
Warning symbols used
A Sharp edges
B Wear glove
C Physical load
D Twopeoplerequired
E Entanglement hazard
F Warning: Can cause personal
injury or equipment damage
Intended use
The EZ-Lift Mount is a system that compensates the mass of vertically moving
applications to ease vertical movement of the application.
General warning
TheapplicationmayonlybeattachedtoorremovedfromtheEZ-Liftwhenthe
EZ-Lift is in closed position. The EZ-Lift is under strong spring force. Only operate
theEZ-Liftwithanadequatelybalancedapplicationattachedtotheapplicationframe.
DonotremoveanypartsoftheEZ-Lift.Onlythenishingcovercanberemoved.
Mounting ttings
MountingttingsarenotincludedwiththeproductObtainadvicefromaspecialist.
Setting the springs
Adjust only the outer springs:
• Adjusttheheightoftheouterspringsequally
• Makesurethattheheightofthedisplayisbalanced
• Increasethespringtensionasmuchaspossible
• Makesurethatthedisplaydoesnotmoveup
Never adjust the inner springs
Disposal of the EZ-Lift
Springs should be unattached before disposal of the EZ-Lift. Sort the EZ-Lift,
the accessories and the packaging for the environmentally friendly recycling.
A
D E F
B C
Never adjust inner springs!

Salamander Interactive Wall Mounts 501-517 [02.21] page 4 of 12
Mounting EZ-LIFT to Wall EZ1/MB26/396
UnpacktheEZ-Lift.Removetheapplicationframecover.Removethewallframe
covers:Undothescrewsfront(1)andside(2)andslideouttothetop(3).
1
2
3
Prepare Mounting Site
TheEZ-Liftwasdesignedtobeinstalledona16”oncenter2”x4”woodstud,or
metalstuds,usinghigh-qualityhollowwalltoggleinstalledinthecenterofthestud
orasolidconcretewall.
WARNING: INSTALLING THE MOUNT IN UNDERRATED OR DAMAGED CONCRETE
CAN LEAD TO SERIOUS INJURY OR DAMAGE TO PRODUCT! When installing into
concreteonlyinstallthemountinasolidconcretewallmadeof2500PSI(17.3MPa)
orstrongerconcrete.Neverinstallthemountintocracked,chippedorakingconcrete.
WARNING: IMPROPER INSTALLATION CAN LEAD TO MOUNT FALLING CAUSING
SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT! It is the installers
responsibilitytomakesurethestructuretowhichtheEZ-Liftisbeinginstalledis
capableofsupportingthreetimesthecombinedweightoftheEZ-Liftandall
attachedequipmentisnottoexceed:497lbs / 225kg
Locating your mount
WOOD CONSTRUCTION:locatetwoframingstuds(minimumof16”
(405mm)apart)atthedesiredlocationusingastudnderdevice.
MASONRY:aminimumwidthof16”(405mm)isrequiredbetweenfasteners.

Salamander Interactive Wall Mounts 501-517 [02.21] page 5 of 12
Mount wall brackets
 Removethewallbracket(4):Undothescrewsleftandrightandremovethebracket.
89 925 45
= 360 =
= 700 =
= 260 =
= 700 =
= 600 =
4
Determine Mounting Height
 Seebelowforrecommendedmountingheightfor84”MicrosoftSurfaceHub
bottom bracket.
45.75”
[1162]
Mounting
Bracket
Hole Position
84”
[2134]
26”
[660]
17”
[432] Approx. Lowest Screen Position
Adjustable
Range

Salamander Interactive Wall Mounts 501-517 [02.21] page 6 of 12
Mount Wall Bracket
 Mountthewallbrackettothewall.Fastenersnotincluded,selectbased
 ontypeofwall.Besurewallstructureissucienttohandleload.
 Accommodates3/8inch(10mm)fasteners.
Lift the EZ-Lift in place. Hold it there. WARNING - VERY HEAVY

Salamander Interactive Wall Mounts 501-517 [02.21] page 7 of 12
 MarkthemountingholesatthetopoftheEZ-LiftTaketheEZ-Liftdown
and put it aside, drill the holes
 LifttheEZ-Liftinplace.Tightenscrewsatthetop.

SalamanderInteractiveWallMounts 501-517[02.21]page8of12
 Putthesecurityscrewsbacksecuringthewallbrackettothe
 EZ-Lift.Donottightenthescrewsyet
 AlwaysleveltheEZ-Liftvertically!Avoiditcrashingintothewall
during use and noise from misalignment. Level the EZ-Lift at the bottom.
 Tightenthesecurityscrews(1)onbothsides.
1

Salamander Interactive Wall Mounts 501-517 [02.21] page 9 of 12
 Mountthewallframecovers(3):Slidetheminfromthetop,makesure
 thetabsatthebottom(5)slideintotheslots.Tightenthescrewsfront
(1) and side (2)
1
23
5
 Mounttheapplicationframecover(optional),tightenthe2screws
on either side at the indicated positions.

Salamander Interactive Wall Mounts 501-517 [02.21] page 10 of 12
1321
52"
100 - 650 4"- 25.6"
770 30.3"
400 - 600
15.75"- 23.6"
32
1.22"
Mounting VESA Bracket to EZ-Lift # EZ1/MA3
 MountthehorizontalprolestotheEZ-Lift.
 NOTE:topandbottomprolesaredierent
Top: Short tab
Bottom: longer tab
M6 x 12mm
(8x)

Salamander Interactive Wall Mounts 501-517 [02.21] page 11 of 12
 Mounttheverticalprolestothetouchpanel.Metrichardware
 6,8and10mmincludedNOTE:holesatthetop
Lift the panel on to the EZ- Lift. NOTE: Flat against the brackets,
 thenloweritHEAVY:TWOPERSONJOB

Salamander Interactive Wall Mounts 501-517 [02.21] page 12 of 12
Center the touch panel on the EZ-Lift
 Nowsecuretheassemblybyinsertingthesecurityscrewsfromthebottom
and tightening them. Use a 4 mm alan key.
M 6 x 1 2 mm ( 2 x )
[13mm]
1/2”
Balancing the EZ-Lift
 BalancetheweightontheEZ-Liftbyloosening(rotatecounterclockwise)
 the4outermostbolts.Useadrilldriveranda1/2”or13mmsocket.Undo
each bolt 5 seconds in turn until the panel is balancing. Fine-tune the balance.
Never adjust inner springs!
LIMITED WARRANTY FOR COMMERCIAL VIDEO DISPLAY STANDS AND MOUNTS
Salamanderwarrantsagainstmanufacturingdefectsfortwo(2)yearsfromthedateofpurchase.Salamanderwillrepairorreplace,atouroption,
anyproductdefectiveinmaterialsorcraftsmanship.Batteriesarenotcoveredbythewarranty.
Fullwarrantyincludinglimitationsandwarrantyclaiminformationmaybefoundatwww.salamandercommercial.com
Subject to printing errors and technical amendments.