Salamander EZ1/MS50/ML095 User manual

Salamander EZ-Touch Manual Lift Wall Mounts - EZ1/MS50/ML095 501-765 [12.22] page 1 of 10
EZ1/MS50/ML095
Consists of:
EZ1/MB16/095
EZ1/MA5
Mount Body
VESA Bracket
EZ1_MS50_ML095
USER MANUAL
EZ-Touch Manual Li Wall Mounts
EZ1/MS50/ML095

Salamander EZ-Touch Manual Lift Wall Mounts - EZ1/MS50/ML095 501-765 [12.22] page 2 of 10
PARTS - EZ1/MS50/ML095
Bracket
for ML095
2x
ML095
EZ1_MS50_ML095 Instructions - Hardware 12-19-22
M6 X 12mm (16x) MS50 Mounting Screws
M8 X 20mm (4x)
M10 X 20mm (4x)
M6 X 12mm (16x) MS50 Mounting Screws
EZ1_MS50_ML095 Instructions - Hardware 12-19-22
M6 X 12mm (16x) MS50 Mounting Screws
M8 X 20mm (4x)
M10 X 20mm (4x)
M8 X 20mm (4x)
EZ1_MS50_ML095 Instructions - Hardware 12-19-22
M6 X 12mm (16x) MS50 Mounting Screws
M8 X 20mm (4x)
M10 X 20mm (4x)
M10 X 20mm (4x)
A
B
2x

Salamander EZ-Touch Manual Lift Wall Mounts - EZ1/MS50/ML095 501-765 [12.22] page 3 of 10
How to use this manual
1 Read manual carefully before you install the mount
2 Carry out the actions fully and in the given sequence
3 The mount guarantee is voided if the product is not correctly installed
 ormodiedinanyway
Warning symbols used
A Sharp edges
B Wear glove
C Physical load
D Twopeoplerequired
E Entanglement hazard
F Warning: Can cause personal
injury or equipment damage
Intended use
The EZ-Touch Mount is a system that compensates the mass of vertically moving displays to
ease vertical movement of the display.
General warning
ThedisplaymayonlybeattachedtoorremovedfromtheEZ-Touchwhenthe
EZ-Touch is in closed position. The EZ-Touch is under strong spring force. Only operate
theEZ-Touchwithanadequatelybalanceddisplayattachedtothedisplayframe.
DonotremoveanypartsoftheEZ-Touch.Onlythenishingcovercanberemoved.
Mounting fasteners
Mountingfastenersarenotincludedwiththeproduct.Obtainadvicefromaspecialist.
Setting the springs
Adjust only the outer springs:
• Adjusttheheightoftheouterspringsequally
• Makesurethattheheightofthedisplayisbalanced
• Increasethespringtensionasmuchaspossible
• Makesurethatthedisplaydoesnotmoveup
Never adjust the inner springs
Disposal of the EZ-Touch
Springs should be unattached before disposal of the EZ-Touch. Sort the EZ-Touch,
the accessories and the packaging for the environmentally friendly recycling.
A
D E F
B C
Never adjust the inner springs!

Salamander EZ-Touch Manual Lift Wall Mounts - EZ1/MS50/ML095 501-765 [12.22] page 4 of 10
Mounting EZ-Touch Mount Body to Wall
UnpacktheEZ-Touchandremovetheplasticcoverandtwofoamblocks.
Locating your mount
WOOD CONSTRUCTION:
locatetwoframingstuds(minimumof16”(405mm)apart)atthedesiredlocationusingastud
nderdevice.
MASONRY:
aminimumwidthof16”(405mm)isrequiredbetweenfasteners.
Packing Foam
Block (2x)
Plastic Cover
Plastic Cover
Packing Foam
Block (2x)
Remove Plastic Cover and Foam Blocks
Installation of EZ1/MS50/ML095 Mount Body
Prepare Mounting Site
TheEZ-Touchwasdesignedtobeinstalledona16”oncenter2”x4”woodstud,ormetalstuds,using
high-qualityhollowwallanchorinstalledinthecenterofthestud
orasolidconcretewall.
WARNING:INSTALLINGTHEMOUNTINUNDERRATEDORDAMAGEDCONCRETECANLEADTO
SERIOUSINJURYORDAMAGETOPRODUCT!Wheninstallingintoconcreteonlyinstallthemountina
solidconcretewallmadeof2500PSI(17.3MPa)
orstrongerconcrete.Neverinstallthemountintocracked,chippedorakingconcrete.
WARNING:IMPROPERINSTALLATIONCANLEADTOMOUNTFALLINGCAUSINGSERIOUS
PERSONALINJURYORDAMAGETOEQUIPMENT!Itistheinstallersresponsibilitytomakesurethe
structuretowhichtheEZ-Touchisbeinginstallediscapableofsupportingthreetimesthecombined
weightoftheEZ-Touchandall
attachedequipmentisnottoexceedthefollowingweightcapacities:
EZ1/MB16/152: 90-152lbs / 40-69kg

Salamander EZ-Touch Manual Lift Wall Mounts - EZ1/MS50/ML095 501-765 [12.22] page 5 of 10
406
16”
300
11.8"
LOCK SCREW HOLE
19
3/4"
Determine mounting height
Seebelowforrecommendedmountingheightfor55”Display.Otherdisplayscanbecalculatedbyadding
halftheheightdierencetothetopandhalftheheightdierencetothebottomoftheexampleshown.
25.7in
653mm
79.5in
2019mm
16in
406mm
41.2in
1046mm
82.88in
2105mm
Mounting
Bracket
Hole Position
Adjustable Range
Approx. Lowest
Screen Position
Determine Mounting Height
Mounting bracket level to wall
UnpacktheEZ-TouchTakethewallbracketout(A)ofthebox.Notetheslotted/slantedholes
forlevelwallmounting.

Salamander EZ-Touch Manual Lift Wall Mounts - EZ1/MS50/ML095 501-765 [12.22] page 6 of 10
Make sure screws are unlocked
Safety warnings, contents of the box, tools needed

16”
12”
1x
2x
MOUNT WALL COVER ATTACH THE SIDE COVERS TO THE
BALANCEBOX®400 USING THE VESA
BRACKET INSTALLATION POINTS AS SHOWN
4x M8
Max 10 mm
Vesa Bracket
EZ1/MA1
1/2”
13mm
Lift the mount onto bracket
Safety warnings, contents of the box, tools needed

16”
12”
1x
2x
MOUNT WALL COVER ATTACH THE SIDE COVERS TO THE
BALANCEBOX®400 USING THE VESA
BRACKET INSTALLATION POINTS AS SHOWN
4x M8
Max 10 mm
Vesa Bracket
EZ1/MA1
1/2”
13mm
Safety warnings, contents of the box, tools needed

16”
12”
1x
2x
MOUNT WALL COVER ATTACH THE SIDE COVERS TO THE
BALANCEBOX®400 USING THE VESA
BRACKET INSTALLATION POINTS AS SHOWN
4x M8
Max 10 mm
Vesa Bracket
EZ1/MA1
1/2”
13mm

Salamander EZ-Touch Manual Lift Wall Mounts - EZ1/MS50/ML095 501-765 [12.22] page 7 of 10
Lock mount with screws
Safety warnings, contents of the box, tools needed

16”
12”
1x
2x
MOUNT WALL COVER ATTACH THE SIDE COVERS TO THE
BALANCEBOX®400 USING THE VESA
BRACKET INSTALLATION POINTS AS SHOWN
4x M8
Max 10 mm
Vesa Bracket
EZ1/MA1
1/2”
13mm
Safety warnings, contents of the box, tools needed

16”
12”
1x
2x
MOUNT WALL COVER ATTACH THE SIDE COVERS TO THE
BALANCEBOX®400 USING THE VESA
BRACKET INSTALLATION POINTS AS SHOWN
4x M8
Max 10 mm
Vesa Bracket
EZ1/MA1
1/2”
13mm
Safety warnings, contents of the box, tools needed

16”
12”
1x
2x
MOUNT WALL COVER ATTACH THE SIDE COVERS TO THE
BALANCEBOX®400 USING THE VESA
BRACKET INSTALLATION POINTS AS SHOWN
4x M8
Max 10 mm
Vesa Bracket
EZ1/MA1
1/2”
13mm
Safety warnings, contents of the box, tools needed

16”
12”
1x
2x
MOUNT WALL COVER ATTACH THE SIDE COVERS TO THE
BALANCEBOX®400 USING THE VESA
BRACKET INSTALLATION POINTS AS SHOWN
4x M8
Max 10 mm
Vesa Bracket
EZ1/MA1
1/2”
13mm
Safety warnings, contents of the box, tools needed

16”
12”
1x
2x
MOUNT WALL COVER ATTACH THE SIDE COVERS TO THE
BALANCEBOX®400 USING THE VESA
BRACKET INSTALLATION POINTS AS SHOWN
4x M8
Max 10 mm
Vesa Bracket
EZ1/MA1
1/2”
13mm
Safety warnings, contents of the box, tools needed

16”
12”
1x
2x
MOUNT WALL COVER ATTACH THE SIDE COVERS TO THE
BALANCEBOX®400 USING THE VESA
BRACKET INSTALLATION POINTS AS SHOWN
4x M8
Max 10 mm
Vesa Bracket
EZ1/MA1
1/2”
13mm
Safety warnings, contents of the box, tools needed

16”
12”
1x
2x
MOUNT WALL COVER ATTACH THE SIDE COVERS TO THE
BALANCEBOX®400 USING THE VESA
BRACKET INSTALLATION POINTS AS SHOWN
4x M8
Max 10 mm
Vesa Bracket
EZ1/MA1
1/2”
13mm
Level vertically with feet at the bottom

Salamander EZ-Touch Manual Lift Wall Mounts - EZ1/MS50/ML095 501-765 [12.22] page 8 of 10
Insert plastic cover
Insert Plastic Cover

Salamander EZ-Touch Manual Lift Wall Mounts - EZ1/MS50/ML095 501-765 [12.22] page 9 of 10
Attach brackets to mount and display
Hang display onto horizontal bracket and level
M8 x 10mm (4x)
M4 x 12mm (10x) or
M6 x 12mm (10x) or
M8 x 12mm (10x)
M6 x 12mm (4x)
Attach Brackets to Display
M6 x 12mm (4X)

Salamander EZ-Touch Manual Lift Wall Mounts - EZ1/MS50/ML095 501-765 [12.22] page 10 of 10
Safety warnings, contents of the box, tools needed

16”
12”
1x
2x
MOUNT WALL COVER ATTACH THE SIDE COVERS TO THE
BALANCEBOX®400 USING THE VESA
BRACKET INSTALLATION POINTS AS SHOWN
4x M8
Max 10 mm
Vesa Bracket
EZ1/MA1
1/2”
13mm
Set balance
Never adjust the inner springs!
Balancing:Springsarealwaysfullytightenedforsafety.Useadrilldriverand10mmsocket,
rotatecounterclockwise(loosen)evenly.Dothreesecondsleftandthreesecondsrightuntilthemount
isevenlybalancedtosupportdisplayweightlessly.
Itmaybenecessarytotightenifbalanced
pointisexceeded.
SALAMANDER WARRANTY
LIMITEDWARRANTYFORCOMMERCIALVIDEODISPLAYSTANDSANDMOUNTS
Salamanderwarrantsagainstmanufacturingdefectsfortwo(2)yearsfromthedateofpurchase.Salamanderwillrepairorreplace,atouroption,any
productdefectiveinmaterialsorcraftsmanship.Batteriesarenotcoveredbythewarranty.
Fullwarrantyincludinglimitationsandwarrantyclaiminformationmaybefoundatwww.salamandercommercial.com
Subject to printing errors and technical amendments.
Lock display with safety lock screws from the bottom
M8 x 10mm (4x)
M4 x 12mm (10x) or
M6 x 12mm (10x) or
M8 x 12mm (10x)
10mm