Salsco 8625 Product manual

O:\Manuals\8625 CHIPPER\8625 Chipper Manual P.W. 10.30.2017.doc - 1 -

O:\Manuals\8625 CHIPPER\8625 Chipper Manual P.W. 10.30.2017.doc - 2 -
TABLE OF CONTENTS
MODEL 8625 WOOD BRUSH/CHIPPER
COVER & TABLE OF CONTENTS……………………………...........…...…..Pages 1 – 2
STATEMENT OF FACT …………………………………..…..….…….….......…… Page 3
SPECIFICATIONS & FEATURES ……………………..……………….. ... ……….Page 4
MACHINE REGISTRATION ……………………………… …..…….......….…….Page 5
SAFETY & OPERATING INSTRUCTIONS ……………………... ….....…..….Pages 6 - 9
SERVICE & MAINTENANCE INSTRUCTIONS …………..…...……....……….…Page 10
PARTS DIAGRAMS ……………………………………………….…...………Pages 11 - 15
...
TORQUE CHARTS ……………………………………… ………………...………Page 16
WARRANTY POLICY AND PROCEDURE ..……………………. ……….…….....Page 17
COPY OF WARRANTY CLAIM FORM….……………………..………....………...Page 18
COPY OF DEALERY DELIVERY REPORT AND WARRANTY CARD………….Page 19
SERVICE SCHEDULE LOG ………………………………………………….……...Page 20
SALSCO, INC.
105 School House Road
Cheshire, CT 06410
800-872-5726, 203-271-1682
203-271-2596 (Fax)
www.salsco.com, [email protected]m

O:\Manuals\8625 CHIPPER\8625 Chipper Manual P.W. 10.30.2017.doc - 3 -
STATEMENT OF FACT
You have just purchased the highest quality, most dependable, Chipper on the market
today. This unit has the ability to meet exact standards and perform for years with
minimum downtime. HOWEVER, it cannot read nor will it understand this manual no
matter how long you leave it on top of the machine.
It is your responsibility to read and understand this manual; it is also your
responsibility to be certain this information is passed along to anyone who is expected to
operate this equipment. Should you choose not to read, understand and pass along the
information provided you, please expect equipment failure and possible injuries to
persons around this equipment.
For the safety of the operator, it is imperative that this manual is carefully read and
understood.
Once you have read this manual, it is your responsibility to be sure that all new operators
read and understand this manual, especially all cautions stated.
As a manufacturer of equipment, we have a responsibility to design a safe piece of
equipment. NOTE: The important safeguards and instructions in this manual are not
meant to cover all possible conditions and situations that may occur. It must be
understood that common sense, caution, and care are factors, which cannot be built into
any product. These factors must be supplied by the person(s) caring for and operating
this equipment.
ONLY YOU CAN PREVENT ACCIDENTS!

O:\Manuals\8625 CHIPPER\8625 Chipper Manual P.W. 10.30.2017.doc - 4 -
SPECIFICATIONS & FEATURES
The Salsco Model 8625 Chipper, like all Salsco products, is ruggedly built to withstand high
volume usage by the rental; commercial lawn care and tree care industries. Standard
equipment includes heavy-duty diamond plate fenders with safety light guards, stop,
directional and safety lights, large 26" diameter high-speed tires, lockable tool box, lockable
battery box, lockable gas and hydraulic fuel tanks. Orange polyester power coated paint
offers protection against ultra violet discoloration, outdoor weatherability and resists most
chemicals.
The trailer frame, constructed of 3" x 2" x 1/4" wall rectangular steel tube, continuous
welded for strength and gusseted where needed, provides years of towing ease. The 2,400
lb. Torflex Axle features an independent suspension, cushioned with rubber, providing a
smooth, quiet ride with no transfer of road shock from one wheel to the other.
Model 8625 has an in feed opening of 6" x 12" to eliminate most pruning of limbs. It will
handle Christmas trees, palm fronds, vines and leafy material with ease. There are two bed
knives, one horizontal and one vertical to prevent material such as fronds and vines from
wrapping around the feed roll. Our feed roll has alternating blades of teeth and cutter
blades; teeth for hard wood and cutter blades for softwood and it measure 7" in diameter by
12" long. Speed of the hydraulic feed is easily adjusted at the hydraulic pump and can be
controlled by the control bar positioned at the top of the chipper infeed chute to
forward/neutral/reverse. The chipper disc is 1" thick by 26" diameter and mounted on a
2" diameter steel shaft with six exhaust blades.
Safety is always our number one concern at Salsco. With the infeed pan down, the feed roll
is 61" from the edge of the pan. The operator would have to work very hard to get a leg or
arm caught in the feed roll. Also provided on each machine is a full set of safety decals.
Simple and safe operation, easy to maintain, and built to last!
Salsco, Model 8625, 6" x 12" Chipper!

O:\Manuals\8625 CHIPPER\8625 Chipper Manual P.W. 10.30.2017.doc - 5 -
MACHINE REGISTRATION
MANUFACTURED BY: SALSCO, INC.
105 School House Rd., Cheshire, CT 06410
800-872-5726, 203-271-1682, 203-271-2596 (Fax)
[email protected]m www.salsco.com
THIS MANUAL COVERS MODEL (s): 8625, 25 HP Kohler, 6” x 12” Chipper
This company reserves the right to discontinue, add improvements to, or change the design of any
model or product at any time without obligation to improve existing machines, either by changing the
design or adding new parts.
It has been and will continue to be the policy of SALSCO to update existing machines at its own
discretion. Whenever possible, new designs will be made in such a way that they can be "Retro Fit" if
so desired.
Record in the space provided below the model and serial number of this unit. Please retain these
numbers for future reference.
No parts orders will be accepted WITHOUT MODEL NUMBERS OR PART NUMBERS. All
part numbers are listed in this manual.
________________________________________ ___________________
Serial Number Model Number
NOTE: Be sure to complete your warranty card. This will insure immediate processing of any
warranty claims.
READ AND UNDERSTAND THIS MANUAL
BEFORE STARTING THE MACHINE
1/06

O:\Manuals\8625 CHIPPER\8625 Chipper Manual P.W. 10.30.2017.doc - 6 -
CAUTIONS
READ THOROUGHLY THE OPERATOR SAFETY INSTRUCTIONS ON THE FOLLOWING
THREE PAGES, WHICH ARE THE AMERICAN NATIONAL STANDARD OF POWERED
SHREDDERS/GRINDERS, SAFETY SPECIFICATIONS PROVIDED BY ANSI AND THE
O.P.E.I.
THE FOLLOWING CAUTIONS ARE PROVIDED BY SALSCO AS A QUICK REFERENCE
ONLY AND ARE NOT MEANT TO REPLACE THE PRECAUTIONS ON THE FOLLOWING
PAGES.
1. ALWAYS use protective eyewear when machine is in operation.
2. ALWAYS use gloves and wear ear protection when machine is in operation.
3. NEVER put hands, legs or any part of your body into or near Chipper intake or discharge
openings.
4. NEVER run with guards removed.
5. ALWAYS allow machine to cool off, remove key and put engine in neutral before attempting
any maintenance or repair.
6. BE SURE machine has stopped completely, engine is off, key is removed and spark plug is
disconnected before attempting any service or maintenance.
7. NEVER stand in front of chipper infeed hopper. It is possible for a chip or piece of wood to be
thrown out.
8. BE SURE the machine is parked on a dry level surface before starting operation.
9. DO NOT operate with loose clothing or long unrestrained hair. Be sure vines and branches are
not wrapped around your body parts.
10. DO NOT operate on ice or any other slippery surface. Be sure area around machine is clear and
clean. You do not want to trip into the machine.
11. NEVER leave machine running unattended, especially around youngsters or persons not
instructed in the safe operation of this machine.
12. READ and understand federal guidelines provided with this manual.

O:\Manuals\8625 CHIPPER\8625 Chipper Manual P.W. 10.30.2017.doc - 7 -
BRUSH CHIPPERS
ANSI Z133.1-2006
American National Standard for Arboricultural Operations
Safety Requirements

O:\Manuals\8625 CHIPPER\8625 Chipper Manual P.W. 10.30.2017.doc - 8 -
BRUSH REMOVAL AND CHIPPING
ANSI Z133.1-2006
American National Standard for Arboricultural Operations
Safety Requirements

O:\Manuals\8625 CHIPPER\8625 Chipper Manual P.W. 10.30.2017.doc - 9 -
OPERATING INSTRUCTIONS
1. Be sure all guards are in place.
2. Check all chambers to be sure they are free and clear of debris.
3. Set direction of discharge chute.
4. Set feed handle in reverse position.
5. Check engine oil and fuel levels, as per engine manufacturer specifications.
6. Set engine throttle just above idle, and set choke.
7. Start engine and let idle for a few minutes to warm up. Open chipper feed tray at this
time.
HINTS
1. When operating machine, stand off to the side of the feed hopper when feeding wood into
the machine. NEVER STAND DIRECTLY IN FRONT OF THE HOPPER WHEN
FEEDING WOOD INTO THE MACHINE.
2. When using the chipper and you have a short piece of wood bouncing around and not
being grabbed by the feed roll, LEAVE IT! DO NOT TRY TO PUSH IT THROUGH
WITH ARMS OR LEGS! The next limb will push it through.
3. When through with the job let the engine run at full RPM, making sure all material is run
through the machine before shutting it down. This will prevent any injuries from flying
debris when the machine is started up at the next job.
WHILE PERFORMING MAINTENANCE OR REPAIR, ALWAYS REMOVE
KEY FROM ENGINE AND REMOVE SPARK PLUG WIRE

O:\Manuals\8625 CHIPPER\8625 Chipper Manual P.W. 10.30.2017.doc - 10 -
SERVICE SCHEDULE
1. Engine - follow service maintenance schedule set forth by the manufacturer in the engine manual.
2. Grease all main bearings once a day. DO NOT OVER GREASE. Wipe extra grease off bearings.
3. Be sure to clean entire machine, especially around engine after using. Should it become necessary
to remove the exhaust chute, either to sharpen the blades or to clean out the machine, REMOVE
SPARK PLUG WIRES AND KEY FROM ENGINE. NEVER TURN ENGINE OVER WHILE
EXHAUST CHUTE IS REMOVED.
4. Sharpen/change chipper blades: REMOVE KEY FROM ENGINE. REMOVE SPARK PLUG
WIRE. Pull pin on impeller housing, open clamshell. Rotate until chip blades are in line with the
opening. DO NOT reach in and hold impeller with your hand, instead use a piece of 2" x 4" wood
to push impeller to desired position. Clean any debris from chip blade pockets to insure proper
seating when replacing blades. When you replace blades, be sure to use Locktite. We use Locktite,
Blue 242, removable at the factory. It is also advisable to discard bolts and use new ones. Sharpen
blades as you would sharpen a lawn mower blade, under angle edge only. Sharpen blades as evenly
as possible. CALL SALSCO ABOUT OUR SHARPENING SERVICE. 800-872-5726
5. Bed knife adjustment on hydraulic feed machines is .070, and should be checked every time blades
are installed or replaced. NOTE: Check distance from each blade.
HINT: It is strongly recommended to have a set of blades and screws on the shelf, to prevent
downtime while blades are being sharpened.
HINT: Blades need sharpening after approximately 8 - 15 hours of use.
6. Check belt for wear and or adjustment: Belt needs adjustment when belt is loose. Adjust belt as
follows: Remove key from engine and spark plug wire, remove inspection door and check belt
tension.
SERVICE SCHEDULE
AS
NEEDED
DAILY
WEEKLY
MONTHLY
CHECK WHEEL BEARINGS
CHECK LUG NUTS
CHECK LIGHTS
CHECK ENGINE OIL
CLEAN MACHINE
GREASE INFEED ROLL BEARING
GREASE DISC SHAFT BEARING
SHARPEN CHIPPER BLADES
CHECK & ADJUST BED KNIFE
CHECK TIRE AIR PRESSURE
CHECK ALL NUTS & BOLTS
CHECK ENGINE BELT TENSION
CHECK HYDRAULIC OIL
CHECK HYDRAULIC HOSES
X
X
X
X
X
X
X
X OR
X OR
X
X
X
X
X
-
-
X
X
X
X
X
-
-
-
X
-
-
-
-
-
-
-
-
-
-
X
X
-
-
X
-
-
-
-
-
-
-
-
-
-
-
X
-
-
X
X
NEVER, UNDER ANY CIRCUMSTANCES START THE ENGINE WHEN UNIT
IS OPEN OR AT ANY TIME DURING SERVICE OR ROUTINE
MAINTENANCE

O:\Manuals\8625 CHIPPER\8625 Chipper Manual P.W. 10.30.2017.doc - 11 -
ITEM #
DESCRIPTION
PART #
QTY.
9
Impeller, Assembly
0105040
1
9-2
Blade, Chipper ¼”
0405016
4
9-3
Screws (3) per Blade
0346150
3
13
Plate, Bearing Mtg.
0241643
2
59
Bearing, Pillow Block
0303032
2
UNITS WITH ACCESS DOOR ON HOUSING USE THE
ABOVE LISTED PARTS WHEN REPLACING BLADES
UNITS WITH FLIP OVER HOUSING USE THE
FOLLOWING PARTS WHEN REPLACING BLADES
DESCRIPTION
PART #
QTY.
Blade, Chipper 3/8”
0305057
4
Bolts
0346152
12
Washer, Lock
0353012
12
Nuts, Lock
0338151
12
NOTE: AFTER S/N 0931, ALL UNITS WILL HAVE ½” x
4” CHIPPER BLADES INSTALLED.
ITEM #
DESCRIPTION
PART #
QTY.
9-2
Chipper Blade, ½”
0305090
4
Bolt
0346487
12
Washer
0353012
12
Nut
0338154
12
ITEM #
DESCRIPTION
PART #
QTY
14
Frame, Power Feed
0219069
1
15
Power Feed Roll
0254028
1
43
Guard, Upper Rubber
Flap
0421073
1
44
Guard, Feed Roll Debris
0221136
1
45
Guard, Feed Roll
Rubber Flap
0421088
1
60
Bearing
0303031
4
67
Hub, 1” I.D.
F185
1
80
Spring, Extension
0350018
2
85
Motor, Hydraulic Drive
0330058
1
88
Collar, Set
0311002
2
89
Eye Bolt
0346860
2
40
Washer, Flat
0353120
2

O:\Manuals\8625 CHIPPER\8625 Chipper Manual P.W. 10.30.2017.doc - 12 -
ANVIL/BED KNIVES
ITEM #
DESCRIPTION
PART #
QTY
10
Housing, Lower Assy.
0228101
1
16
Bed Knife, Horizontal
0441581
1
17
Bed Knife, Vertical
0441582
1
HARDWARE FOR BED KNIVES
Washers, Lock
0353005
7
Washers, Flat
0353129
7
Bolt, Hex Head
0346403
7
ADJUSTMENT BOLT FOR HORIZONTAL BED KNIFE
Bolt
0346414
1
Nut, Hex
0338005
1
ITEM #
DESCRIPTION
PART #
QTY
46
Guard, Assembly
0221089
1
47
Guard, Plate
0471023
1
48
Guard, Lower
0221092
1
49
Cable, Push/Pull,
72”
0308022
1
53
Engine, 25 HP
Kohler
0337048
1
55
Sheave
0342043
1
56
Bushing, SK
0342029
1
57
Sheave
0342026
1
58
Bushing, SD
0342034
1
61
Belt, Model 8625
0304038
1
78
Nipple, 3/8 NPT
0317099
1
79
Elbow, 3/8 HPT 90
0317100
1
91
Muffler
0337032
1
92
Plug, 3/8 NPT
0317101
1

O:\Manuals\8625 CHIPPER\8625 Chipper Manual P.W. 10.30.2017.doc - 13 -
ITEM #
DESCRIPTION
PART #
QTY
1
TOW BAR ASSEMBLY
0225012
1
2
COUPLER, 2" BALL
0325007
1
ITEM # 3 –JACK –TWO STYLES USED: EITHER
BRACKET MOUNTED (SHOWN) OR TOP WIND
(NOT SHOWN)
3
Jack, Swivel
0369001
1
Jack, Top Wind
0369006
1
4
Jack Mount Bracket
0369002
1
5
Tow Frame Assembly
0219070
1
6
Axle Spacer
0449067
4
7
Left Fender
0216011
1
8
Right Fender
0216012
1
50
Axle Assembly
0302075
1
51
Lug Nuts
0338306
10
52
Tire/Wheel Assembly
0354025
2
54
Trailer Light Kit
0361006
1
84
Safety Chain
0309018
1
ITEM#
DESCRIPTION
PART #
QTY
32
Tank, Gas (Steel)
0252011
1
32
Tank, Fuel (Poly-Marine)
S/N 3160 and Up
(Not Retro-Fit)
0352102
1
32
Tank, Fuel (Poly-Marine)
Before S/N 3160
0352006
1
33
Cap, Gas/Oil
0318004
2
34
Cap, Locking Gas/Oil
0271024
2
37
Box, Battery
0280001
1
38
Cover, Battery Box
0271020
1
39
Box, Tool
0280002
1
40
Cover, Tool Box
0271021
1
62
Cable, Battery
0315057
2
63
Top Post Terminal
0315058
2
64
Eyelet Cable
0315059
2
65
Barb
0317097
1
66
Battery
0315060
1
83
Grease Gun
0369004
1
(Optional)

O:\Manuals\8625 CHIPPER\8625 Chipper Manual P.W. 10.30.2017.doc - 14 -
HYDRAULIC COMPONENTS
ITEM #
DESCRIPTION
PART #
QTY
27
Tank, Hydraulic Oil
0252012
1
ITEM #
DESCRIPTION
PART #
QTY
ITEM #
DESCRIPTION
PART #
QTY
28
Hydraulic Filter
0318002
1
72
Adapter
0317058
1
31
Bracket, Hydraulic Pump
0406289
1
73
Adapter
0317069
1
33
Cap, Gas/Oil
0318004
2
74
Adapter
0317064
4
34
Cap, Locking Gas/Oil
0271024
2
75
Adapter, 90 Degree
0317053
2
35
Lever, Hydraulic Pump
0433042
1
76
Adapter, 45 Degree
0317098
2
36
Bracket, Guard Mtg.
0476054
1
77
Hose, Hydraulic 31”
0327028
1
68
Hose, Hydraulic 42”
0327070
2
81
Key, Woodruff
0331502
1
69
Adapter, 90 Degree
0317040
2
82
Set Screw
0346276
2
70
Hose, Hydraulic 18”
0327036
2
85
Motor, Hydraulic
0330058
1
71
Adapter
0317030
2
86
Pump, Hydraulic
0330021
1
87
Plug, ¼ NPT
0317070
2

O:\Manuals\8625 CHIPPER\8625 Chipper Manual P.W. 10.30.2017.doc - 15 -
UPPER EXHAUST ASSEMBLY
ITEM#
DESCRIPTION
PART #
QTY
1
Discharge Chute
0226031
1
2
Chute Deflector
0426028
1
3
Wing Nut
0238500
1
4
Clamp, Front Half
0210067
1
5
Wing Nut, Chute
Clamp
0238501
2
6
Housing, Impeller,
Lower
0228128
1
7
Housing, Impeller,
Upper (Fixed)
0228129
1
8
Housing, Impeller,
Upper (Movable)
0228130
1
9
Hinge Pin, Lower
Hsg.
0440050
1
10
Pin, Locking
0240051
1
11
Clamp, Rear Half
0210168
1
LOWER HOUSING ASSEMBLY
ITEM #
DESCRIPTION
PART #
QTY
10
Housing Lower
Assembly
0228101
1
18
Lid Assembly
0271018
1
19
Power Feed Handle
Assembly
0223031
1
24
Yoke, Detent
Bracket
0274004
1
25
Bearing, Ball
0303034
1
29
Mount, Engine
0276014
1
30
Mount, Engine &
Muffler
0276020
1
41
Guard, Right Wing
0221070
1
42
Guard, Left Wing
0421072
1

O:\Manuals\8625 CHIPPER\8625 Chipper Manual P.W. 10.30.2017.doc - 16 -
BOLT SIZE
Thds Per Inch
SAE Grade 5
SAE Grade 8
¼
20
28
10
---
14
---
5/16
18
24
19
---
29
---
3/8
16
24
33
---
47
---
7/16
14
20
54
---
78
---
½
13
20
78
---
119
---
9/16
12
18
114
---
169
---
5/8
11
11
154
---
230
---
¾
10
10
257
---
380
---
7/8
9
9
382
---
600
---
1
8
8
587
---
700
---
Below is a quick reference chart for various “Flat Head
Cap Screws” and the torque recommendations.
VALUES ARE STATED IN FOOT POUNDS

O:\Manuals\8625 CHIPPER\8625 Chipper Manual P.W. 10.30.2017.doc - 17 -
WARRANTY POLICY
Please remember to complete and return your Warranty Card and Dealer Delivery Report. Warranty
Claims will not be considered if the Warranty Card and Dealer Delivery Report have not been
returned to Salsco.
Your Salsco Commercial or Turf Equipment product is a commercial type product and is normally manufactured and sold for commercial or
industrial use. Salsco will, for the original purchaser, for one (1) year from the date of purchase (90 days if used for rental purposes) repair or
replace, free of charge, any SALSCO part or parts found to be defective in material, workmanship or both. Any transportation or shipping
charges will be borne by the purchaser. If, during the warranty period stated above, the product does not function properly due to defect, simply
contact Salsco and follow the Warranty Procedures included in this manual.
This warranty does not include:
•Incidental or consequential damages and is exclusive of any implied warranties.
•Normal maintenance parts, including, but not limited to hoses, chains, belts, filters, lubricants, etc.
•Parts or components, which are covered under the original manufacturer warranty, including, but not limited to engines, pumps, and
motors.
WARRANTY PROCEDURE
In order for Salsco to consider your warranty claims in a timely manner you must follow the simple procedures listed below:
MACHINE OR PART FAILURE
a) Call our service department for helpful instruction on how to correct or repair the problem. Preventive maintenance will also be suggested.
b) When ordering parts for Warranty issues, you MUST retain possession of the old parts in question until notified with respect to returning the
parts to Salsco or other disposition.
c) Warranty Claims MUST be filed within 30-days from completion of the work performed. Contact our office for an electronic warranty claim
form.
d) Fill in all information requested on warranty claim form, a copy of which is included in this manual, (date of purchase, company name, address,
etc.). List all parts used. Make sure part numbers are correct. You can obtain these from your manual. (include good description of problem;
i.e. “leaking from spool” rather than “leaking”).
e) It is our goal to consider and reach a disposition on each Warranty Claim within 30-days from the date that it is received. Therefore it is
important that you respond promptly to any request for further information. Claims with no response to inquiries will be closed as “denied for
lack of response” 90-days from the date of request.
f) Email, Fax or Send Warranty Claim form to our Warranty Department. –Warranty on parts most often requires return of the parts that
were replaced. DO NOT DISCARD OLD PARTS UNTIL YOU HAVE RECEIVED A DETERMINATION AS TO WHETHER THESE
PARTS MUST BE RETURNED.
g) Our Warranty Department will contact and instruct you on how to return the Parts to Salsco on an RA #. Returns MUST be made within 30-
Days from issuance of RA #. FREIGHT CHARGES ON RETURN OF PARTS IS THE RESPONSIBILITY OF THE CUSTOMER.
Normal pre-delivery adjustments are not covered under warranty. Labor Warranties are based on reasonable time allowances as determined by
Salsco, Inc. and paid at 75% of posted labor rate. TRAVEL TIME IS NOT REIMBURSED UNDER THE WARRANTY POLICY.
h) Be sure to put the RA form inside the box that you are shipping back, also be sure to put on the outside of the box “Return of Goods” and the
RA #.
i) Ship returns via a traceable method such as UPS Ground Service. Be sure that the shipment is insured for the appropriate value. If uninsured
parts are lost, we cannot issue a credit.
PLEASE NOTE: Warranty forms should be filled out completely.
PREVENTIVE MAINTENANCE IS YOUR BEST INSURANCE AGAINST EQUIPMENT FAILURE. BE SURE TO READ THIS
MANUAL, ESPECIALLY THE MAINTENANCE, OPERATING AND CAUTION SECTIONS.
SALSCO, INC., 105 School House Rd.
Cheshire, CT 06410
800-872-5726, 203-271-1682
203-271-2596 (Fax)
[email protected], www.salsco.com

O:\Manuals\8625 CHIPPER\8625 Chipper Manual P.W. 10.30.2017.doc - 18 -

O:\Manuals\8625 CHIPPER\8625 Chipper Manual P.W. 10.30.2017.doc - 19 -

O:\Manuals\8625 CHIPPER\8625 Chipper Manual P.W. 10.30.2017.doc - 20 -