Samil Power UL3-10K WIFI User manual

User Manual for UL3-10K WIFI
User Manual for UL3-10K WIFI
Table of Contents
1. Initialize WIFI Module .......................................................................................................2
2. WIFI Parameters Setting....................................................................................................3
3. Get IP Address of WIFI ...................................................................................................... 7
4. Problems & Solutions ........................................................................................................ 8

User Manual for UL3-10K WIFI
1. Initialize WIFI Module
It’s necessary to initialize WIFI module before WIFI settings. The method is showed as below:
Press these 3 buttons at the same time
ESC
▲
▼
Initialize
WiFi Parameters
？
OK
E
WiFi
Reset
WiFi
Initialize OK

User Manual for UL3-10K WIFI
2. WIFI Parameters Setting
2.1 After initializing WIFI module, you can search a wireless network named HF-LPB100 or HF-LPB
with a laptop. This network can be connected directly without any password, and connect it
please.
2.2 Input the IP address 10.10.100.254 in your browser, and a login window will appear after
pressing the “Enter” key. The user name is admin, and the password is admin too. Please
input the login messages and click “OK”

User Manual for UL3-10K WIFI
2.3 Click “STA Setting” and set as follow:
(a) Input the network name and password of your Router.
(b) Make it enable to obtain an IP address automatically.
(c) Click “Save” to save the settings.
(Note: Don’t restart after saving successfully, please click “Back” to do following settings.)

User Manual for UL3-10K WIFI
2.4 Click “Other Setting” and set network parameters base on the monitor you choose.
(1) If you choose to use local monitor, please set as follow:
Protocol：TCP-Server
Port ID: 60000
TCP Time Out Setting：300
Click “Save” below the page to save settings.
(Note: Don’t restart after saving successfully, please click “Back” to do following settings.)
(2) If you choose to use remote monitor which is named V-Iplant, please set as follow:
Protocol：UDP
Port ID: 1400
Server Address：210.75.240.157
Click “Save” below the page to save settings.
(Note: Don’t restart after saving successfully, please click “Back” to do following settings.)

User Manual for UL3-10K WIFI
2.5 Click “Work Mode”, select “STA mode”, and then click “Save”.
(Note: Don’t restart after saving successfully, please click “Back” to do following settings.)

User Manual for UL3-10K WIFI
2.6 Go to the “Restart” page and click “OK” to restart. So far, settings of WIFI parameters are
finished.
3. Get IP Address of WIFI
After having finished setting WIFI parameters, user can get current IP address of WIFI through
the LCD of inverter. It means that the connection between WIFI module and Router haven’t been
established if the IP address is 0.0.0.0 . The method to read the IP address is showed as bellow:
P-out
：
1200W
E-day
：
3KW OK ▲
Events
Service →
OK
▲
S/N: SU312345678
Get WiFi IP……
OK S/N: SU312345678
55.41.31.178

User Manual for UL3-10K WIFI
4. Problems & Solutions
4.1 Failed to establish connection between WIFI module and Router.
Solution: When the IP address you get from LCD is 0.0.0.0, please restart the power of inverter
and try to read IP address again. If it still doesn’t work, maybe the SSID or password of Router
have been incorrectly input when setting the WIFI parameters. Please initialize the WIFI module
and reset the WIFI parameters. It is important to make sure the SSID and password of Router are
correct.
4.2 It can’t connect to the local or remote monitor.
Solution: Login the setting pages of WIFI with the IP address you get from LCD. Check if the
network parameters on the “Other Setting” page have been set correctly.
4.3 No response from WIFI setting pages.
Solution: Maybe your browser is not compatible with the WIFI module. Please change a browser
to login and the IE browser is recommended.