Samson XP 106 User manual

Owner's Manual
E PEDITION
XP106
PORTABLE PA WITH

2
Copyright 2013
v2
Samson Technologies Corp.
45 Gilpin Avenue
Hauppauge, New York 11788-8816
Phone: 1-800-3-SAMSON (1-800-372-6766)
Fax: [phone]
www.samsontech.com
The Bluetooth® word mark and logos are registered trademarks owned by
Bluetooth SIG, Inc. and any use of such marks by Samson Technologies is
under license. Other trademarks and trade names are those of their respective
owners.”

3
XP106 • Portable PA System
Important Safety Information
WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK) AS THERE ARE NO
USER-SERVICEABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
This lightning flash with arrowhead symbol within an equilateral triangle
is intended to alert the user to the presence of non-insulated “danger-
ous voltage” within the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance in-
structions in the literature accompanying the appliance.
AVIS
RISQUE DE CHOC ÉLECTRONIQUE -
NE PAS OUVRIR
If you want to dispose this product, do not mix it with general household waste. There is a
separate collection system for used electronic products in accordance with legislation that
requires proper treatment, recovery and recycling.
Private household in the 28 member states of the EU, in Switzerland and Norway may return their
used electronic products free of charge to designated collection facilities or to a retailer (if you
purchase a similar new one).
For Countries not mentioned above, please contact your local authorities for a correct method of
disposal.
By doing so you will ensure that your disposed product undergoes the necessary treatment, recovery
and recycling and thus prevent potential negative effects on the environment and human health.
ENGLISH
FRANÇAISDEUTSCHEESPAÑOLITALIANO

4
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation open-
ings. Install in accordance with the
manufacturer’s instructions.
8. Do not install near any heat sources
such as radiators, heat registers,
stoves, or other apparatus (including
amplifiers) that produce heat.
9. Do not defeat the safety purpose of
the polarized or grounding type plug.
A polarized plug has two blades with
one wider than the other. A grounding
type plug has two blades and a third
grounding prong. The wide blade or
the third prong are provided for your
safety. If the provided plug does not
fit into your outlet, consult an electri-
cian for replacement of the obsolete
outlet.
10. Protect the power cord from being
walked on or pinched particularly at
the plugs, convenience receptacles,
and at the point where they exit from
the apparatus.
11. Only use attachments/accessories
specified by the manufacturer.
12. Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the ap-
paratus. When a cart is used, use
caution when moving the cart/appara-
tus combination to avoid injury from
tip-over.
13. Unplug the apparatus during lighten-
ing storms or when unused for long
periods of time.
14. Refer all servicing to qualified
personnel. Service is required when
the apparatus has been damaged in
any way, such as power supply cord
or plug is damaged, liquid has been
spilled or objects have fallen into the
apparatus has been exposed to rain or
moisture, does not operate normally,
or has been dropped.
15. This appliance shall not be exposed
to dripping or splashing water and
that no object filled with liquid such
as vases shall be placed on the ap-
paratus.
16. Caution-to prevent electrical shock,
match wide blade plug wide slot fully
insert.
17. Please keep a good ventilation envi-
ronment around the entire unit.
18. To prevent injury, this apparatus must
be securely attached to the stand
in accordance with the installation
instructions.
19. WARNING: The battery (battery or
batteries or battery pack) shall not
be exposed to excessive heat such as
sunshine, fire or the like.
20. CAUTION: Danger of explosion if bat-
tery is incorrectly replaced. Replace
only with the same or equivalent type.
Important Safety Information

5
XP106 • Portable PA System
Important Safety Information
FCC Notice
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the fol-
lowing two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may
cause undesired operation.
2. Changes or modifications not expressly approved by the party responsible for compli-
ance could void the user’s authority to operate the equipment.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digi-
tal device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
RF Warning Statement
The device has been evaluated to meet general RF exposure requirement. The device
can be used in portable exposure condition without restriction.
This device complies with RSS-310 of Industry Canada. Operation is subject to the
condition that this device does not cause harmful interference.
ENGLISH
FRANÇAISDEUTSCHEESPAÑOLITALIANO

6
Table of Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Control Panel Features . . . . . . . . . . . . . . . . . . . . . . 9
Quick Start . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Pairing with a Bluetooth® device . . . . . . . . . . . . . . . . .12
Charging the Battery . . . . . . . . . . . . . . . . . . . . . . .13
Speaker Placement . . . . . . . . . . . . . . . . . . . . . . . 14
Avoiding Feedback. . . . . . . . . . . . . . . . . . . . . . . .15
Quick Start - Stage XPD1 Wireless System . . . . . . . . . . . . 16
Stage HXD1 Handheld Transmitter Controls . . . . . . . . . . . . 18
Stage RXD1 Receiver Controls . . . . . . . . . . . . . . . . . . 19
Using the LINE IN/OUT Jack . . . . . . . . . . . . . . . . . . .20
Making Connections . . . . . . . . . . . . . . . . . . . . . . . 21
XP106 Specifications . . . . . . . . . . . . . . . . . . . . . . 22

7
XP106 • Portable PA System
Introduction
Thank you for purchasing the XP106 battery-powered portable sound system,
featuring wireless Bluetooth®connectivity, to stream audio from your smart
phone, tablet, or computer. The XP106 is a complete all-in-one solution provid-
ing the flexibility of a four-channel mixer (with inputs for a microphone and line
level devices), a line output for linking multiple speakers, and a Music/Speech
tone switch.
For added flexibility, the XP106 mixer has a USB jack for connecting the
Samson Stage XPD1 digital handheld wireless system, creating a completely
cordless performance.
Lightweight and compact, the XP106 features 100 watts of power weighing
less than 20lbs, makes it an excellent complement to any mobile speaker
application. The internal battery provides up to 20 hours of audio on a full
charge. The XP106 can also be powered by the included AC adaptor for
continuous audio.
Whether you are looking for a sound system for use outdoors, in the classroom,
for karaoke, for presentations, or performing live music, the XP106 provides
high quality, portable audio in a small self-powered package.
We recommend you keep the following records for reference, as well as a copy
of your sales receipt.
Serial number: ____________________________________________
Date of purchase: __________________________________________
Dealer name: _____________________________________________
With proper care and maintenance, your XP106 will operate trouble-free for
many years. Should your speaker ever require servicing, a Return Authorization
(RA) number must be obtained before shipping your unit to Samson. Without
this number, the unit will not be accepted. Please call Samson at 1-800-
3SAMSON (1-800-372-6766) for an RA number prior to shipping your unit.
Please retain the original packing materials and, if possible, return the unit in
its original carton. If your XP106 was purchased outside of the United States,
contact your local distributor for warranty details and service information.
ENGLISH
FRANÇAISDEUTSCHEESPAÑOLITALIANO

8
• Lightweight, 100 watt PA system that weighs under 20 pounds
• Bluetooth connectivity to connect wireless music sources
• 2-way speaker enclosure with 6-inch woofer and 1-inch high frequency
driver
• Four channel mixer with microphone, line level, and USB wireless receiver
inputs.
• Integrated 1 3/8-inch speaker stand mount
• Ergonomic top carry handle
• Internal rechargeable battery for up to 20 hours of continuous use
• System equalization contour switch for music and spoken word applica-
tions
• Link output for expanding your sound system
Accessories
• XP106 - Dynamic handheld microphone with XLR cable
• XP106w - Stage XPD1 digital handheld wireless system with USB receiver
and handheld transmitter
Features

9
XP106 • Portable PA System
Control Panel Features
1. MIC/INST Input - Use this
XLR/1⁄4" input for microphone,
instrument with and active
preamp or a line signal.
2. LEVEL (CHANNEL 1) - Used to
control the level of the CHAN-
NEL 1 Mic/Line input.
3. AUX IN - Connect a line level
device using a 3.5mm audio
cable.
4. LINE Input - ¼" input used to
connect instrument or line
level signals.
5. LEVEL (CHANNEL 2) - Used to
control the level of the MP3
IN and LINE inputs.
6. 2.4GHz WIRELESS Input* - Con-
nect the Samson Stage XPD1
digital wireless USB receiver
to this input. The wireless receiver gets its power from the XP106, so no
additional power supply is needed.
7. LEVEL (WIRELESS) - Used to control the level of the 2.4GHz WIRELESS
input.
8. LINE OUT - ¼" output connector to link multiple XP106 systems together
9. LEVEL (BLUETOOTH®) - Used to control the level of the Bluetooth input.
10. SPEECH/MUSIC Switch - This switch is used to change the overall fre-
quency response, or tone contour, for the XP106 sound system. If your
application is mainly for music, leave the switch up to select the MUSIC
response curve. If your application is mainly for spoken word, press the
switch down to select the SPEECH response curve.
11. Power - Switches on the main power.
12. PEAK LED - The Red LED illuminates at the level where distortion occurs.
13. Battery Indicator - Displays the status of the battery charge level.
14. DC IN - Connect the supplied power adapter here.
2
5
7
9
11
1
4
8
10
14
6
12
13
3
VOL
* The USB connector is for the Stage XPD1 receiver only. The connector is
not designed to charge smartphones, tablets, or similar devices.
ENGLISH
FRANÇAISDEUTSCHEESPAÑOLITALIANO

10
15. Pairing Indicator - Displays the
Bluetooth status of the XP106
system.
16. Pairing Button - Press this but-
ton to enable pairing mode in
order to connect to a Blue-
tooth audio device.
Control Panel Features
15
16

11
XP106 • Portable PA System
Follow these steps below to
quickly get started using your
XP106 portable sound system.
• Set the XP106's power
switch to the OFF
position, and fully turn
all of the LEVEL controls
counterclockwise to 0.
• If an outlet is available,
connect the included power
adaptor to the DC IN of the
speaker, and plug it into an
AC socket.
• Connect a microphone
using a standard XLR cable,
line level equipment using
a 1⁄4" instrument cable, or
portable audio device using
a 1⁄8" cable.
• Switch on the XP106
power.
• While speaking into the microphone or playing music from a line level
audio source, slowly raise the channel LEVEL until you have reached the
desired level.
NOTE: If not using the channel 1 input, turn the LEVEL control all the way down to
keep out any unwanted noise.
Quick Start
Setting a Good Level
Use the Channel LEVEL controls to set the individual volume of your micro-
phone, line level and Bluetooth®devices.
The PEAK light illuminates when the signal sending to the internal amplifier
begins to reach a level where distortion occurs. If the PEAK lights stay on,
your mix is too hot and you need to lower the LEVEL controls. It is okay for the
PEAK light to occasionally light, however it should go off quickly and should
not constantly stay on.
ENGLISH
FRANÇAISDEUTSCHEESPAÑOLITALIANO

12
Bluetooth®is a wireless communication technology that allows for connectivity
between a wide range of devices. The XP106 uses Bluetooth to stream high quality
audio from your Bluetooth enabled device without the need for connecting any
cables. In order for your device to work with the XP106 it must first be paired.
1. Turn all channel VOL controls down counterclockwise to 0.
2. With the XP106 and your Bluetooth device powered on; press the PAIR
button on the top panel of the XP106 speaker to make the speaker discov-
erable. The Bluetooth indicator will slowly flash blue.
3. In the settings of your Bluetooth device, set it to “discover” available
devices.
4. From the Bluetooth device list, select the
"Samson XP106" device.
5. If your device asks for a passkey, enter
digits 0000 (four zeros) and press OK.
Some devices may also ask you to accept
the connection.
6. As the XP106 is connecting to your device,
the Bluetooth indicator will quickly flash
blue.
7. The XP106 speaker indicates that pairing
is complete when the indicator turns steady
blue. You can now stream audio from your
device to the XP106 speakers.
8. With the volume control on your Bluetooth
device turned up, play some music, and
slowly raise the XP106 BLUETOOTH chan-
nel VOL control until you have reached the
desired level.
Pairing with a Bluetooth® device

13
XP106 • Portable PA System
The XP106 has an internal, rechargeable battery capable of up to 20 hours
of continuous audio on a full charge. Even though the system may have some
charge when first taken out of the box, we recommend fully charging your
XP106 before first using the system.
To charge the battery:
• Set the power switch to the
“OFF” position.
• Connect the XP106 to an
AC power outlet using the
included power adapter.
• Keep the system plugged in
until the Battery indicator
changes to green, indicating
the battery is fully charged.
The XP106 utilizes a sealed lead-acid gel cell battery. When not in use, the
battery will slowly self-discharge. If you are planning not to use the XP106
for a long period of time, it is advised to fully charge the unit before storing.
It is also important to charge the unit every six months when not used. This
will ensure a healthy battery and extend its life. If the battery is left with a
very low charge for an extended period of time, it is possible to recharge the
battery to working condition, but the charge time can take over 24 hours.
If you find that the operation time of the XP106 becomes noticeably
decreased, even after fully charging, the battery should be replaced. Contact
Samson customer service or your local distributor for a replacement battery.
Charging the Battery
ENGLISH
FRANÇAISDEUTSCHEESPAÑOLITALIANO

14
The XP106 provides three different placement options for your specific
situation.
For maximum sound coverage the XP106
can be used with a standard 13⁄8” speaker
stand. The speaker should be raised above
the heads of the listening audience. Take
care when placing the speaker on a stand,
to ensure that it is on a level, steady surface
and will not tip over.
Take care when placing the XP106 in direct sunlight for long periods of time,
as this may discolor or damage the unit.
Do not place the speaker on wet surfaces, as it can cause malfunction. If you
notice condensation on the unit, dry the speaker before using or storing.
Speaker Placement

15
XP106 • Portable PA System
Feedback is the annoying howling and squealing that can heard when the
microphone picks up sound from the speaker. The sound is then re-amplified
back through the speaker again, creating a feedback loop. Follow these steps to
minimize the likelihood of feedback:
• Avoid pointing the microphone directly at the speaker. In general it is
recommended that the microphone be positioned behind the speaker
enclosure. This uses the directional characteristics of the speaker and
microphone to your advantage.
• Keep the microphone as far from the speaker as possible. This will help
achieve isolation between the speaker and the microphone, and allow you
to increase the output of the XP106.
• Position the microphone as close to the sound source as possible. This
will enable the microphone to pick up more direct sound, and allow you to
reduce the microphone input gain control.
• Reduce the overall level of the speaker.
Avoiding Feedback
ENGLISH
FRANÇAISDEUTSCHEESPAÑOLITALIANO

16
Quick Start - Stage XPD1 Wireless System
Plug the RXD1 USB receiver into the
USB jack labeled 2.4GHz WIRELESS.
On the wireless handheld transmitter,
unscrew the bottom section of
the microphone by turning it
counterclockwise and then slide it off.
Place a fresh set of AA (LR6) batteries
in the transmitter battery holder,
taking care to observe the polarity
markings, then replace the cover.
Turn the WIRELESS LEVEL
knob on the XP106 completely
counterclockwise to 0, then turn the
POWER siwtch on the XP106 to the
ON position.
Turn on the power to the transmitter
by pressing and holding Power switch;
the indicator LED will light amber.

17
XP106 • Portable PA System
Quick Start - Stage XPD1 Wireless System
If the handheld transmitter and
receiver have not been previously
paired, press and hold the button on
the RXD1 receiver for >5 seconds,
until it begins to flash.
Press and hold the Power button on
the handheld transmitter >5 seconds.
This will put both components into
pairing modes. Once the receiver and
transmitter communicate and sync,
the LEDs on both units will light
steady and will be ready for operation.
Speak or sing into the mic at a normal
performance level and raise the
WIRELESS LEVEL control until the
desired level is reached.
If you hear distortion check the rear
panel PEAK LED. If it is lit red, turn down
the WIRELESS LEVEL on the XP106
until it lights only occasionally during
loud sounds. If you still hear distortion,
unscrew the microphone body and use
the supplied plastic screwdriver to turn
the Gain control in the HXD1 transmitter
slowly counterclockwise until the
distortion disappears.
Conversely, if you hear a weak, noisy
signal at the desired volume level (and
with the WIRELESS control of the XP106
turned fully clockwise), use the supplied
plastic screwdriver to turn the Gain
control in the HXD1 transmitter slowly
clockwise until the signal reaches an
acceptable level.
ENGLISH
FRANÇAISDEUTSCHEESPAÑOLITALIANO

18
1. Status Indicator - This LED displays the opera-
tion mode:
Amber Normal Operation
Flashing Amber Pairing/Low Battery
2. Power/Pair Switch - Press <5 seconds to
turn the unit on or off. Press >5 seconds
to enter pairing mode.
3. Battery Cover - Unscrew the battery cover
and slide down to open the HXD1 battery
compartment.
4. Battery Holder - Open the battery holder
by pressing the tab and lifting the cover.
Insert two standard AA (LR6) batteries
here, being sure to observe the plus and
minus polarity markings shown. Although
rechargeable Ni-Cad batteries can be
used, they do not supply adequate current
for more than four hours. WARNING: Do
not insert the batteries backwards; doing
so can cause severe damage to the HXD1
and will void your warranty.
5. Input GAIN Control - This control adjusts the transmitter input sensitivity.
This input sensitivity control has been factory preset to provide optimum level for
the particular microphone capsule provided with the Stage XPD1 system and so we
recommend that this not be adjusted manually. If necessary, however, you can use
the supplied plastic screwdriver to raise or lower the input level.
Stage HXD1 Handheld Transmitter Controls

19
XP106 • Portable PA System
Stage RXD1 Receiver Controls
1. USB Connector - Plugs into the USB 2.4GHz Wireless jack on
the rear panel of the XP106. The receiver can also plug directly
into a computer USB port and will be recognized as a USB
audio device. The unit passes audio to the device and receives
power from the device through this connector.
2. PAIR Switch - Press >5 seconds to enter pairing mode.
3. STATUS Indicator - This LED displays the operation mode:
Amber Normal Operation
Flashing Amber Pairing
No Light Not Paired; Transmitter Out Of Range;
No Power
1
2
3
ENGLISH
FRANÇAISDEUTSCHEESPAÑOLITALIANO

20
The XP106 LINE OUT jack allows you to connect the XP106 with any powered
speaker to expand your system or link two XP106 systems together and share
all inputs between the two units. You can also use the jack to receive audio
from another speaker without using an input channel.
Daisy Chain Speaker
Using a standard shielded ¼ instrument cable, connect the LINE OUT on the
XP106 to a line level input of second powered speaker. The XP106 will send a
mix of all inputs, including Bluetooth® audio. Each channel LEVEL will control
corresponding output level to the LINE OUT jack.
Linking Two XP106 Systems
To use two XP106’s as one system is simple. Just connect each side using a
standard ¼" Shielded instrument cable to the LINE OUT jack located on each
XP106 rear panel. Both mixers and the microphones or instruments connected
to each of the individual XP106 systems will be heard in both speakers.
Auxiliary Line Input
The LINE OUT jack can be used to accept any line level input source. This
input does not have a level control, so you must utilize the output level of the
connected device to control the level of the audio in the XP106.
Using the LINE OUT Jack